Kyocera KM 8030 User Manual

Preparing to Copy
2-5
5Insert the appropriate paper size card in the slot to 
indicate the size of the paper inside.
6Gently push the cassette back in.
Loading Paper in the MP Tray
The MP tray supports special paper (45 to 200 g/m²) in addition to standard and recycled paper. Up 
to 100 sheets of standard paper (80 g/m²) may be loaded in the MP tray. 
The MP tray accepts paper sizes from 5 
1/2×8 1/2 to 11 × 17 and from 16K, 8K, Folio, A6R, and 
B6R to A3.
The capacity of the MP tray is as follows....

Preparing to Copy
2-6
2Adjust the paper width guides to fit the width of the 
paper.
3Insert the paper along the paper width guides into the 
tray until it stops.
Ensure that the paper width guides are flush against 
the edges of the paper.
IMPORTANT: Before loading postcards and other 
types of thick paper that may be curled, straighten out 
the paper. The paper may not be fed depending on the 
paper quality.
Only load the MP tray when you are using. Avoid 
leaving paper in the MP tray.
Ensure that the...

Preparing to Copy2-7
2Open the right cover.
NOTE: When the right cover is open, the paper lifter 
will not descend if you press the switch for the paper 
lifter.
It is easier to load new paper with the top cover open.
3Align the paper flush against the left side in the back of 
the feeder as you load it.
IMPORTANT:  Before loading the paper, be sure that it 
is not curled or folded. Paper that is curled or folded 
may cause paper jams.
Ensure that the loaded paper does not exceed the 
level indicated....

Preparing to Copy
2-8
Specifying Paper Type and Size to the Cassettes and MP Tray
After loading paper in the cassettes 1 or 2 or the optional side feeder (cassette 5), specify the paper 
type. Refer to Specifying the Paper Type on page2-9 for details.
After loading paper in the cassettes 3 or 4, specify both the paper type and size. Refer to Specifying 
the Paper Size below and Specifying the Paper Type on page2-9.
After loading paper in the MP tray, specify both the paper type and size. Refer to...

Preparing to Copy
2-9
4Press [S] or [T] to choose Paper size 
[3rd drawer] (Paper size [3rd cassette]) 
or Paper size [4th drawer] (Paper size 
[4th cassette]). Press [Change #] to 
begin changing settings.
5When [Auto Detection] is selected, 
choose the unit of measurement. When 
[Standard sizes] is selected, choose the 
paper size. 
Press [Close].
[Close]: Returns to the previous page by 
holding the settings.
[Back]: Returns to the previous page by 
canceling the settings.
6Press [Close].
7Press...

Preparing to Copy
2-10
3Use the numeric keys to enter the 
four-digit management code. By default, 
the management code is 6000 for 60 
cpm model and 8000 for 80 cpm model.
4Press [S] or [T] to choose from Paper 
type (1st drawer) (Paper type [1st 
cassette]) through Paper type (5th 
drawer) (Paper type [5th cassette]). 
Press [Change #] to begin changing 
settings.
NOTE: Paper type (5th drawer) (Paper 
type [5th cassette]) is displayed when 
installing the optional side feeder.
5Select the paper type...

Preparing to Copy
2-11
Specifying the Paper Size to the MP Tray
Specify the paper size when using the MP tray. 
Select the paper size from the followings. 
Auto Detect
The paper size is automatically detected. Specify [Centimeter] or [Inch].
1Press the System Menu/Counter key.
2Press [MP tray Setting].
3Press [Auto Detection].
4Press [Centimeter] or [Inch].
5Press [Close]. The touch panel will return to the [Basic] screen. Setting Method Unit Paper Sizes
Auto Detect Inch 11 × 17, 8 
1/2×14, 11×81/2,...

Preparing to Copy
2-12
Other Standard Sizes
Specify special standard sizes.
1Press the System Menu/Counter key.
2Press [MP tray Setting].
3Press [Others Standard] and then 
[Select size].
4Select the paper size.
5Press [Close].
6Press [Close]. The touch panel will return to the [Basic] screen.
System Menu / Counter
Job Sy stem Menu
Management BOX
Re p o r t Pri nt L anguage
MP  tr a y
Or i g. Si ze Re g i s te r
Management Document
Defaul t Ma ch i n e Defaul t Co p y
Setti ngAccounti ng
MP tr a y  Se...

Preparing to Copy
2-13
Input Size
Specify the required paper size.
1Press the System Menu/Counter key.
2Press [MP tray Setting].
3Press [Input size].
4Press [+] or [-] to specify the vertical 
size. With the metric models, you may 
enter the size directly using the numeric 
keys by pressing [#-Keys].
The setting range is as follows.
System Menu / Counter
Job Sy stem Menu
Management BOX
Re p o r t Pr i nt Language
MP  tr a y
Or i g. Si ze Re g i ste r
Management Document
Defaul t Ma ch i n e Defaul t Co p...

Preparing to Copy
2-14
5Press [+] or [-] to specify the horizontal 
size. With the metric models, you may 
enter the size directly using the numeric 
keys by pressing [#-Keys].
The setting range is as follows.
6Press [Close]. The touch panel will return to the [Basic] screen.
Specifying the Paper Type to the MP Tray
Specify the paper type when using the MP tray. 
The following paper types are available. 
Plain, Transparency, Rough, Vellum, Labels, Recycled, Preprinted, Bond, Cardstock, Color 
(Colour),...