Kyocera KM 2560 User Manual

Preparation before Use 
OPERATION GUIDE2-47
2
Loading Originals
Follow the steps below to load originals for copying, sending or storing.
Placing Originals on the Platen
You may place books or magazines on the platen in addition to ordinary 
sheet originals.
1Open the original cover.
NOTE: If the optional document processor is installed, open the 
document processor. Before opening the document processor, be sure 
that there are no originals left on the original table or on the original eject 
table....

Preparation before Use 
2-48OPERATION GUIDE ‹Original size indicator plates
(Inch models)
(Metric models)
3Close the original cover.
IMPORTANT: Do not push the original cover forcefully when you close it. 
Excessive pressure may crack the platen glass.
NOTE: Shadows may be produced around the edges and in the middle 
of open-faced originals.
CAUTION: Do not leave the document processor open as there is a 
danger of personal injury.
Downloaded From ManualsPrinter.com Manuals 

Preparation before Use 
OPERATION GUIDE2-49
2
Loading Originals in the Document Processor
The optional document processor automatically scans each sheet of 
multiple originals. Both sides of two-sided originals are scanned.
Part Names of the Document Processor
(1) Original placement indicator
(2) Top cover
(3) Original width guides
(4) Original table
(5) Original eject table
(6) Opening handle
Originals Supported by the Document Processor
The document processor supports the following types of originals....

Preparation before Use 
2-50OPERATION GUIDE • Originals with correction fluid which is not dried
• Irregularly shaped (non-rectangular) originals
• Originals with cut-out sections
• Crumpled paper
• Originals with folds (Straighten the folds before loading. Failure to do 
so may cause the originals to jam).
• Originals bound with clips or staples (Remove the clips or staples and 
straighten curls, wrinkles or creases before loading. Failure to do so 
may cause the originals to jam).
How to Load...

Preparation before Use 
OPERATION GUIDE2-51
2
Ensure that loaded originals do not exceed the level indicator. Exceeding 
the maximum level may cause the originals to jam (see the figure below).
Originals with punched holes or perforated lines should be placed in such 
a way that the holes or perforations will be scanned last (not first).
Original placement indicator
The original placement 
indicator is lit or unlit 
depending on how originals 
are placed.
Indications and their status are 
as follows.
•...

Preparation before Use 
2-52OPERATION GUIDE
Downloaded From ManualsPrinter.com Manuals 

OPERATION GUIDE3-1
3 Basic Operation
This chapter explains the following operations.
• Power On/Off................................................................ 3-2
• Low Power Mode and Auto Low Power Mode ............. 3-4
• Sleep and Auto Sleep................................................... 3-5
• Adjusting the Operation Panel Angle ........................... 3-6
• Touch Panel Display ..................................................... 3-7
• Copying...

Basic Operation 
3-2OPERATION GUIDE
Power On/Off
Power On
Open the main power switch cover and turn the main power switch on.
Blinking/Lighting of each Key/Indicator
When turning on the main power switch, Key/Indicators such as Copy or 
Send blink.
Blinking:  This function is in preparation. When each key is ready, the 
indicator lights out one by one.
Unlit: This function is ready.
Lit:  This function is selected. Copy is selected as the default so that 
the Copy key/indicator lights on first.
NOTE: A...

Basic Operation 
OPERATION GUIDE3-3
3
IMPORTANT: Do not turn the main power switch off when the optional fax 
kit is installed. If you  turn the main power switch off, you cannot receive fax 
messages.
In case of not using the machine for a extended period of time
CAUTION: If the machine will not be used fo r an extended period of time 
(vacations, etc.), remove the power plug  from the outlet for safety purposes 
and remove paper from the cassettes and seal it in the paper storage bag 
to protect it...

Basic Operation 
3-4OPERATION GUIDE
Low Power Mode and Auto Low Power Mode
Low Power Mode
To activate Low Power Mode, press the Energy Saver key. Touch panel 
and all indicators on the operation panel will go out to save power except 
the Energy Saver, Power, and main power indicators. This status is 
referred to as Low Power Mode.
If print data is received during Low Power Mode, the machine automatically 
wakes up and starts printing.
Also when fax data arrives while the machine is in Low Power Mode...