Kyocera KM 1650 User Manual

Printer Settings 
ADVANCED OPERATION GUIDE 2-13
4Press S or T to select On or Off 
and press [Enter]. If On is 
selected, Change # displays.
5Press S or T to select Change # 
and press [Enter].
6Press S or T to select the frame 
mode and press [Enter].
7Press [Reset]. The Printer Basic screen displays.
EtherTalk
Set this option to On if connecting to an Apple Macintosh computer.
1Display the Interface screen, refer to Access the Interface Screen, on page 
2-11.
2Press S or T to select Network 
and press...

Printer Settings 
2-14 ADVANCED OPERATION GUIDE
TCP/IP
Set this option to On if connecting to a Windows network via TCP/IP.
1Display the Interface screen, refer to Access the Interface Screen, on page 
2-11.
2Press S or T to select Network 
and press [Enter].
3Press S or T to select TCP/IP 
and press [Enter].
4Press S or T to select On and 
press [Enter].
DHCP
Set this option to On if using DHCP (Dynamic Host Configuration Protocol).
1Display the TCP/IP screen, refer to TCP/IP, on page 2-14.
2Press S or...

Printer Settings 
ADVANCED OPERATION GUIDE 2-15
IP Address Setting
Use the following procedure to register an IP Address to the machine. 
Check with your network administrator before performing this procedure.
If you use the following procedure to register the IP Address manually, 
ensure DHCP is Off and TCP/IP is On. 
NOTE: Any changes made to network settings become valid after you 
power the machine off and on again.
1Display the TCP/IP screen, refer to TCP/IP, on page 2-14.
2Press S or T to select...

Printer Settings 
2-16 ADVANCED OPERATION GUIDE
Subnet Mask Setting
Continue from the previous Step 6 to register the Subnet Mask address.
NOTE: If you are not sure of the appropriate Subnet Mask address, 
contact your Network Administrator.
1Display the TCP/IP Setting screen.
2Press S or T to select Subnet 
Mask and press [Enter].
3Enter the Subnet Mask address 
using the same procedure used 
for the IP Address in steps 8 - 9 of 
IP Address Setting.
Press [Enter] when the entire address has been...

Printer Settings 
ADVANCED OPERATION GUIDE 2-17
Network Status Page Printing
When printing the Status Page, you can also print the network status page 
in succession.
1Display the Interface screen, refer to Access the Interface Screen, on page 
2-11.
2Press S or T to select Network 
press [Enter].
3Press S or T to select Network 
Status Page and press [Enter].
4Press S or T to select On or Off 
and press [Enter]. 
5Press [Reset]. The Printer Basic screen displays.
Back
Parallel
In terf ac e
Network...

Printer Settings 
2-18 ADVANCED OPERATION GUIDE
Emulation
The following settings are available:
• Emulation Mode Selection
• KC-GL Pen Thickness
• KPDL Error Printing
• KPDL (AUTO) Alternative Emulation Selection
NOTE: You can set the emulation for each interface.
Emulation Mode Selection
Emulation modes that can be used with this machine: PCL6, KC-GL, 
KDPL, KDPL (AUTO), Line Printer, IBM Proprinter, Diablo 630, EPSON 
LQ-850 
If you set KC-GL, you can set the thickness of the pen and page size.
If you...

Printer Settings 
ADVANCED OPERATION GUIDE 2-19If you have selected KC-GL, refer to KC-GL Pen Thickness, on page 2-19.
If you have selected KPDL or KPDL (AUTO), refer to KPDL Error Printing, 
on page 2-20.
If you have selected KPDL (AUTO), refer to KPDL (AUTO) Alternative 
Emulation Selection, on page 2-20.
KC-GL Pen Thickness
If you have selected KC-GL emulation, you can set the thicknesses of the 
eight pens and the page size. Continue the procedure from step 5 of 
Emulation Mode Selection to setup....

Printer Settings 
2-20 ADVANCED OPERATION GUIDE
KPDL Error Printing
The details of any error that occurs during printing in the KPDL emulation 
mode can be printed. Continue the procedure from step 5 of Emulation 
Mode Selection to set up.
1Press S or T to select Print 
KPDL Errs and press [Enter].
If On is selected, the details of any 
error will be printed.
2Press [Reset]. The Printer Basic screen displays.
KPDL (AUTO) Alternative Emulation Selection
If you set KPDL (AUTO), switching between KPDL and...

Printer Settings 
ADVANCED OPERATION GUIDE 2-21
Font
You can select the default Font for the current interface. The default Font 
can be one of the internal fonts or a font stored in the optional Memory 
Card.
The following settings are available:
• Font Selection
•Font Size
• Courier/Letter Gothic Font Character Pitch
• Courier/Letter Gothic Thickness
• Code Set
• Printing a Font List
NOTE: You can set the font for each interface.
 Access the Font Screen
1Press [Printer].
2Press S or T to select MENU...

Printer Settings 
2-22 ADVANCED OPERATION GUIDE
Font Selection
NOTE: If optional fonts as well as internal fonts are stored on the 
machine, a screen for selecting Internal font or Option font displays. Press 
S or T to select the font to set.
1Display the Font screen, refer to Access the Font Screen, on page 2-21.
2Press S or T to select Select 
Font and press [Enter].
3Press S or T to select the Font 
ID and press [Enter].
The font number displays.
Characters displayed before font 
numbers indicate the...