Kyocera KM 1650 User Manual

Printer Settings 
ADVANCED OPERATION GUIDE 2-3
e-MPS Function
The following settings are available:
• Quick Copy/Proof-and-Hold
• Private Print/Stored Job
• Virtual Mailbox
• Virtual Mailbox List
• Code Job List
• e-MPS Detail Settings
NOTE: To use the e-MPS functions, the optional Hard Disk must be 
installed. For details on e-MPS, refer to the KX Printer Driver Operation 
Guide.
NOTE: If the RAM Disk Operation (refer to page 2-41) is switched On, 
the e-MPS function can still be used for Proof-and-hold...

Printer Settings 
2-4 ADVANCED OPERATION GUIDE
Quick Copy/Proof-and-Hold
Quick Copy and Proof-and-hold are selected from the printer driver.
When a Quick Copy job is received, the machine stores it in memory until 
the user enters the number of copies required and prints the job.
When a Proof-and-hold job is received, the machine prints one set and 
then stores the job in memory. The user can check the proof, change the 
number of copies if required and print the remaining sets.
NOTE: For information...

Printer Settings 
ADVANCED OPERATION GUIDE 2-5
Private Print/Stored Job
If Private is selected on the printer driver, the user enters a 4-digit access 
code prior to sending the job. The job is then held in memory until the user 
enters the same 4-digit access code to enable the job to print. The data is 
cleared after printing.
If Stored job is selected, there is no restriction on access. The job is printed 
and then stored in memory.
NOTE: For information about the printer driver options, refer to the...

Printer Settings 
2-6 ADVANCED OPERATION GUIDE
Deleting Private Print/Stored Job
Each stored job can be deleted manually as shown below:
1Select the job to delete, refer to Private Print/Stored Job, on page 2-5.
2Press S or T to select Delete and 
press [Enter].
Virtual Mailbox
Virtual Mailbox is selected from the printer driver and is used to store jobs 
on the machine. A job will remain in a Virtual Mailbox until the 5-digit 
access code (set using KM-NET Printer Disk Manager) is entered to 
enable the...

Printer Settings 
ADVANCED OPERATION GUIDE 2-7
Virtual Mailbox List
A list can be printed which shows the current Virtual Mailbox numbers, the 
data stored in a mailbox, the size of data stored and other information.
1Display the e-MPS screen, refer to Access e-MPS, on page 2-3.
2Press S or T to select List of 
VMB and press [Enter].
3Press S or T to select Print and 
press [Enter].
The virtual mailbox list is printed.
P ri vate/ S to red
Print VMB Data
e-MP S
List of VMB
No
Print
List of VMB
VIRTUAL...

Printer Settings 
2-8 ADVANCED OPERATION GUIDE
Code Job List
Permanent code jobs in the hard disk can be printed.
1Display the e-MPS screen, refer to Access e-MPS, on page 2-3.
2Press S or T to select List of 
code JOB and press [Enter].
3Press S or T to select Print and 
press [Enter].
The code job list is printed.
Print VMB Data
List of VMB
e-MP S
List of Code JOB
No
Print
List of Code JOB
PERMANENT CODE JOB LIST
Downloaded From ManualsPrinter.com Manuals 

Printer Settings 
ADVANCED OPERATION GUIDE 2-9
e-MPS Detail Settings
The e-MPS settings such as the maximum number of documents that can 
be stored on the hard disk and the capacity assigned to each function, can 
be changed.
Maximum Number - Quick Copy Jobs
1Display the e-MPS screen, refer to Access e-MPS, on page 2-3.
2Press S or T to select e-MPS 
Configuration and press [Enter].
3Press S or T to select Quick 
Copy and press [Enter].
4Press < or > to select the 
maximum number of jobs that can 
be...

Printer Settings 
2-10 ADVANCED OPERATION GUIDE
Total Capacity - Permanent Code Jobs
Use to set the total capacity for storage of permanent code jobs on the hard 
disk. 
1Display the e-MPS screen, refer to Access e-MPS, on page 2-3.
2Press S or T to select e-MPS 
Configuration and press [Enter].
3Press S or T to select Perm 
Code Job Size and press [Enter].
4Press < or > to select the total 
capacity for storage of permanent 
code jobs, 0 to 9999 MB can be 
selected. Press [Enter].
NOTE: The actual...

Printer Settings 
ADVANCED OPERATION GUIDE 2-11
Interface
This machine is equipped with a parallel, USB and network interface as 
standard.
The following settings are available:
• Parallel Interface
• Network Setting
• IP Address Setting
• Subnet Mask Setting
• Default Gateway
• Network Status Page Printing
Access the Interface Screen
1Press [Printer].
2Press S or T to select MENU 
and press [Enter].
3Press S or T to select Interface 
and press [Enter].
Setup the options required.
Parallel Interface
The...

Printer Settings 
2-12 ADVANCED OPERATION GUIDE
NOTE: Use a parallel interface cable that complies with the IEEE 1284 
standard.
1Display the Interface screen, refer to Access the Interface Screen, on page 
2-11.
2Press S or T to select Parallel 
and press [Enter].
3Press S or T to select the 
transmission/reception mode 
required and press [Enter].
4Press [Reset]. The Printer Basic screen displays.
Network Setting
To perform network printing, network setup is required. This section 
describes the tasks...