Kyocera FS 2020D User Manual

COMMAND CENTER Pages
Operation Guide 37
If nothing is specified on this page, access from all hosts is allowed.
Advanced > Protocols > TCP/IP > Logical Printers
This page allows you to configure the Logica l Printers. This machine can be used as a 
virtual printer for converting ASCII print data  to PostScript data or for adding and/or 
replacing a character strings (commands) at th e beginning or end of job data. Up to four 
logical printers can be set. Item
Description
IP Filter (IPv4)
IP Address...

COMMAND CENTER Pages
38KYOCERA COMMAND CENTER
Each logical printer can be used with either the FTP, LPR, IPP, NetBEUI, or Raw Port 
protocol. All printout to a non-existent port will be accomplished to Logical Printer1.
Advanced > Protocols > Netware
This printing system supports both NDS and bindery printing in either print server mode 
or remote printer mode.
NetWare setup requires installation of t he following client software and logon with 
Administrator Privileges. If you are unsure,  please...

COMMAND CENTER Pages
Operation Guide 39
Advanced > Protocols > IPP
Using IPP (Internet Printing Protocol) or IPP over SSL, you can output to the printing 
system over the Internet or an intranet.
Advanced > Protocols > AppleTalk
You can print from Macintosh comput ers using the AppleTalk protocol.
The printing system network component  supports Mac OS of various versions (System 
Requirements  on page 1) and is compatible with LaserWriter driver version 8.x. 
NDS Context
Enter the NDS Context.
Print...

COMMAND CENTER Pages
40KYOCERA COMMAND CENTER
To set up the Ethernet interface to communicate via AppleTalk, enables AppleTalk 
protocol operation on the printing system.
Advanced > Protocols > NetBEUI
Peer-to-peer printing is available using Net BEUI protocol. With this method, the printing 
system is located in Windows Network Neighborhood.
Advanced > E-mail > SMTP > General
This machine can send Low Toner and other  information via E-mail to the specified mail 
address. To use the mail function,...

COMMAND CENTER Pages
Operation Guide 41
Advanced > E-mail > SMTP > E-mail Recipient #
This page allows you to set the address fo r receiving E-mail and contents of event 
reports. Up to three re cipients can be set.
Authentication 
Protocol
Enables or disables the SMTP authentication protocol or 
sets 
POP before SMTP  as the protocol. The SMTP 
authentication supports Microsoft Exchange 2000.
Authenticate as Specifies the user to be authenticated in SMTP 
authentication. When POP3 User 
1 to  3 (refer...

COMMAND CENTER Pages
42KYOCERA COMMAND CENTER
Advanced > E-mail > POP3 > General
To use the E-mail function, you need to connect the printing system to an E-mail server 
using the POP3 protocol.Subject
Specifies the information to be displayed at Subject. When 
the following variable starting 
with % is entered, it is 
converted to values for information set on this machine and 
displayed at Subject. - %printer = Model 
- %serial = Serial Number 
- %etheraddr = MAC Address
- %host = Host Name 
- %ip = IP...

COMMAND CENTER Pages
Operation Guide 43
Advanced > E-mail > POP3 > User # 
This page allows you to set the POP3 user account and information on the POP3 server. 
Up to three users can be set.
Advanced > Management > SNMP > SNMPv1/v2c
The SNMP protocol is used for providing and transferring management information 
within the network environment. Should an error occur such as  Add Paper, the printing 
system automatically generates a  trap, an error message sent to up to two pre-
determined trap...

COMMAND CENTER Pages
44KYOCERA COMMAND CENTER
Advanced > Management > SNMP > SNMPv3
The table below provides a summary of the items displayed on the SNMPv3 page.After you 
have changed this setting, you must restart th is machine. For the restarting procedure, 
refer to  Basic > Defaults > Reset  on page 9.
Read 
CommunityThe read community can be used like a password. The 
default read community name is 
public. After you have 
changed this setting, you must restart this machine. When a 
management...

COMMAND CENTER Pages
Operation Guide 45
Advanced > Management > LDAP
The FAX System can refer to the address book which is on the LDAP server as an 
external address book and assign a FAX numb er and E-mail address to the destination.
Hash
Selects the hash algorithm. This
 item is displayed when the 
Authentication  is On.
Privacy Sets whether to encrypt the communicated data in SNMP 
communication. This becomes available when 
Authentication
 is enabled.
Encryption Selects the encryption algorithm....

COMMAND CENTER Pages
46KYOCERA COMMAND CENTER
Advanced > Management > Authentication
Setting Authentication  allows only the predefined users to access pages. In addition, 
you can discriminate user s by giving either the General User or Administrator  privilege 
to each user. Before using t he authentication function, you ha ve to define those users. 
For how to define users, refer to  Basic > Security > User Login on page 13.
NOTE: If the server type is [Kerberos (Win2000/2003)], only domain names...