Konica Minolta magicolor 5670EN User Manual
Here you can view all the pages of manual Konica Minolta magicolor 5670EN User Manual. The Konica manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 271
CompactFlash card 257 CompactFlash card If a CompactFlash card is installed, resources such as fonts, macros and pro- files can be downloaded, and image files can be printed directly. Only CompactFlash cards with a capacity of 512 MB, 1 GB or 4 GB can be used. The Hold Job function is not available with a CompactFlash card. These functions require that an optional hard disk kit be installed. Installing the CompactFlash card Note If the installed CompactFlash card was used with a device other than...
Page 272
CompactFlash card 258 2Using a screwdriver, remove the screw. Then, slide the rear cover to the right and remove it. 3Using a screwdriver, loosen the seven screws. (Do not remove them from the printer.) 4Slide the panel slightly to the right and lift it off the printer. Downloaded From ManualsPrinter.com Manuals
Page 273
CompactFlash card 259 5Fully insert the CompactFlash card into the appropriate slot. When the CompactFlash card is correctly inserted, the button on the top side of the slot (circled in the illustration) slightly pops out. Before removing the CompactFlash card, press in this button. 6Reinstall the panel and tighten the seven screws. 7Attach the rear cover. 8Reconnect all interface cables. 9Reconnect the power cord, and turn on the printer. 10Declare the Memory card in the Windows printer driver...
Page 274
Duplex Option 260 Duplex Option Duplex (double-sided) printing can be performed automatically with the duplex option and enough memory installed. See “Duplexing” on page 147. Installing the Duplex Option 1Turn off the printer. 2Remove the cover on the right side cover. Downloaded From ManualsPrinter.com Manuals
Page 275
Duplex Option 261 3Remove the door at the side of the right side cover. 4Prepare the duplex option. Before installing the duplex option, open the duplex cover, and then check that the knob is positioned as shown in the illustration. Then, close the duplex cover. 5Attach the duplex option, as shown in the illustration. Downloaded From ManualsPrinter.com Manuals
Page 276
Duplex Option 262 6Open the duplex cover, and then turn both knobs counterclock- wise until they are horizontal to secure the duplex option to the right side cover. 7Then, close the duplex cover. 8Declare the Duplex Unit in the Windows printer driver (Properties/Config- ure tab). Downloaded From ManualsPrinter.com Manuals
Page 277
Lower Feeder Unit 263 Lower Feeder Unit You can install up to two optional lower feeder units (Trays 3 and 4). Each lower feeder unit increases your printer’s media feed capacity by 500 sheets. Kit Contents „Lower feeder unit with a tray (500-sheet capacity) „Four metal brackets –Two front brackets –Two rear brackets „Four securing screws „Transport guide (used only for Tray 3) Downloaded From ManualsPrinter.com Manuals
Page 278
Lower Feeder Unit 264 Installing a Lower Feeder Unit Note Since consumables are installed in the printer, be sure to keep the printer level when moving it in order to prevent accidental spills. 1Turn off the printer and discon- nect the power cord and inter- face cables. 2Prepare the lower feeder unit. Be sure to place the lower feeder unit on a level surface. 3Open the right side cover of the lower feeder unit. The right side cover of the lower feeder must be opened before the feeder can be...
Page 279
Lower Feeder Unit 265 4With another person’s help, place the printer on top of the lower feeder unit, making sure that the positioning pins on the lower feeder unit correctly fit into the holes on the bottom of the printer. If two lower feeder units are to be installed, stack the two lower feeder units and secure them together before installing them to the printer. WARNING! This printer weighs approximately 44 kg (97.0 lb) when it is fully loaded with consumables. The printer must be lifted by...
Page 280
Lower Feeder Unit 266 6Pull out the trays. 7Install the two securing brackets at the front of the printer. 8Close the trays. 9Attach the transport guide to the right door of Tray 3. It is not necessary to attach the transport guide to the right door of Tray 4. Downloaded From ManualsPrinter.com Manuals