Konica Minolta magicolor 5670EN User Manual

Status, Error, and Service Messages 237
Status, Error, and Service Messages
Status, error, and service messages are displayed in the control panel mes-
sage window. They provide information about your printer and help you locate 
many problems. When the condition associated with a displayed message 
has changed, the message is cleared from the window.
Standard Status Messages
This message... means... do this...
CALIBRATINGAfter replacing a toner car-
tridge or a print unit, or after 
rebooting your...

Status, Error, and Service Messages 238
Error Messages (Warning: )
“I-UNIT” in a message refers to the print unit.
REBOOTINGThe printer is being 
restarted.No action needed.
WARMING UPThe printer is warming up.
OFFLINEThe printer is offline. To print on a 
network, change 
the TELNET 
setting so it is 
online.
This message... means... do this...
FUSER UNIT
END OF LIFEThe fuser unit has 
reached the end of its 
life.Contact Technical Sup-
port with the error infor-
mation.
HDD 
NEAR FULLThe hard disk is...

Status, Error, and Service Messages 239
INCORRECT
TONER XThe X toner cartridge 
is an unapproved 
type.Install a 
KONICA MINOLTA toner 
cartridge of the appropri-
ate type (AM, EU, AP or 
GC). See page 155.
MEMORY CARD
NEAR FULLThe memory card is 
nearly full.Delete resources (fonts, 
forms, etc.) which saved 
on the memory card by 
using Download Man-
ager or PSWC.
NON SUPPORT
CARDSince incompatible 
CompactFlash card 
was inserted into the 
memory slot, the 
CompactFlash card 
could not be used.Use...

Status, Error, and Service Messages 240
I-UNIT LOW
XThe X print unit is low 
and should be 
replaced within 2,000 
pages at 5% cover-
age of letter/A4 
pages. 
(Appears when 
SYS 
DEFAULT MENU/
ENABLE WARN-
ING/I-UNIT LOW
 
is set to 
ON.)Prepare the specified 
color print unit.
I-UNIT LIFE
XThe X print unit has 
reached the end of its 
life.Replace the print unit.
STAPLER EMPTYThe staple finisher 
has run out of staples. 
Otherwise, the 
staples are almost 
empty.Replace the staple 
cartridge.
TONER...

Status, Error, and Service Messages 241
TRANS. BELT
END OF LIFEThe transfer belt unit 
has reached the end 
of its life.Replace the transfer belt 
unit and reset the 
counter in the 
MAINTE-
NANCE MENU/SUP-
PLIES/REPLACE/
TRANS. BELT
 menu.
TRANS.ROLLER 
END OF LIFEThe transfer roller has 
reached the end of its 
life.Replace the transfer 
roller and reset the 
counter in the 
MAINTE-
NANCE MENU/SUP-
PLIES/REPLACE/
TRANS. ROLLER
 
menu.
UNABLE TO 
COLLATE JOBThe hard disk is full. 
Print jobs over 10,000...

Status, Error, and Service Messages 242
Error Messages (Operator Call: )
This message... means... do this...
ADJUST TRAY1Tray 1 is removed 
from the printer.Install Tray 1
COVER OPEN 
DUPLEX COVERThe duplex cover is 
open.Close the duplex cover.
COVER OPEN 
FINISHER COVERThe finisher cover is 
open.Close the finisher cover.
COVER OPEN 
FRONT COVERThe printer’s front 
cover is open.Close the front cover.
COVER OPEN 
SIDE COVERThe printer’s right 
side cover is open.Close the right side 
cover.
COVER OPEN...

Status, Error, and Service Messages 243
MANUAL FEED
“SIZE”
“MEDIA”The Paper Source in 
the printer driver is 
set to Tray 1 (Manual 
Feed), but there is 
already media in the 
tray when printing 
begins.Press the   key to 
print, or remove and 
reload the media in Tray 
1.
MEMORY FULL
PRESS CANCELThe printer has 
received more data 
than can be pro-
cessed with its inter-
nal memory.Press the Cancel key to 
cancel the print job.
Decrease the amount of 
data to be printed (for 
example, by decreasing 
the...

Status, Error, and Service Messages 244
PAPER JAM
DUPLEX1Media has misfed in 
the duplex option.Press the   key to dis-
play the help screen. 
Follow the instructions in 
the help screen to 
remove the misfed 
media.
PAPER JAM
DUPLEX2Media has misfed in 
the duplex option.
PAPER JAM
FINISHERMedia has misfed in 
the transport section 
of the staple finisher.
PAPER JAM
FUSER/EXITMedia has misfed 
leaving the fuser 
area.
PAPER JAM
MAIN EXITMedia has misfed in 
the feed section of the 
main output tray....

Status, Error, and Service Messages 245
I-UNIT END
REPLACE
XThe X Print unit has 
completely reached 
the end of its life.Replace the Print unit.
I-UNIT MISSING
CHECK XThe X print unit is not 
installed, or an unap-
proved print unit is 
installed.Install a correct KONICA 
MINOLTA print unit.
STAPLER EMPTY
REPLACE STAPLE
CARTRIDGEThe staples are 
empty when an 
attempt was made to 
print a staple job.Replace the staple car-
tridge.
TONER OUT 
REPLACE XThe X toner cartridge 
is completely empty.Replace...

Status, Error, and Service Messages 246
TRAYX SIZE ERR
ADD
“SIZE”The media size set in 
the printer driver is 
different from the size 
of media loaded.Load the correct media 
size into the specified 
tray.
TRAYX TYPE ERR
ADD
“MEDIA”The media type set in 
the printer driver is 
different from the type 
of media loaded.Load the correct media 
type into the specified 
tray.
WASTE TONER FULL
REPLACE BOTTLEThe waste toner 
bottle is full.Install a new waste toner 
bottle.
CONFIGURATION ERRThe printer...