Konica Minolta magicolor 5670EN User Manual

Lower Feeder Unit 267
10Close the right side cover of the 
lower feeder unit.
11Declare Paper Source Unit 3/4 in the Windows printer driver (Properties/
Configure tab).
Downloaded From ManualsPrinter.com Manuals 

Staple Finisher 268
Staple Finisher
When the staple finisher is installed, job separation, offset and staple printing 
can be performed.
Accessories
1
6
2
5
4
3
71
3
4
5
2
67
1 Staple Finisher
2 Relay Unit
3 Main output tray
4 Sub output tray
5 Hooks (For securing the 
relay unit)
6 Hooks (For installing the 
staple finisher)
7 Mounting clips for the main 
output tray
Downloaded From ManualsPrinter.com Manuals 

Staple Finisher 269 Unpacking and installing the Staple Finisher
1Open the box for the optional finisher.
2Unpack the relay unit, and then 
open the relay unit cover
3Remove all packing tape.
4Close the relay unit cover.
Downloaded From ManualsPrinter.com Manuals 

Staple Finisher 270
5Remove the two mounting hooks 
in the bag taped to the back of 
the relay unit.
Since the gears (1) are 
exposed, be careful not 
to grab them or hit them.
Since the performance of 
the transport roller and 
springs (2) may be 
greatly reduced if they 
are firmly grabbed, treat 
them with special care.
6Turn off the machine and discon-
nect the power cord and inter-
face cables.
2
1
Downloaded From ManualsPrinter.com Manuals 

Staple Finisher 271
7Remove the output tray from the 
machine.
While lightly bending the 
output tray as much as 
possible, remove the out-
put tray.
8Remove the inside cover (three 
locations) at the top of the 
machine.
9Use a coin to remove the front 
cover (two locations) at the top 
of the machine.
Downloaded From ManualsPrinter.com Manuals 

Staple Finisher 272
10Install the relay unit on the 
machine.
11Open the relay unit cover.
Downloaded From ManualsPrinter.com Manuals 

Staple Finisher 273
12With your fingers, press the left 
and right pins. Make sure that 
the pins are pushed in.
13Secure the relay unit on the 
machine with the two mounting 
hooks.
14Lock the relay unit lever.
Downloaded From ManualsPrinter.com Manuals 

Staple Finisher 274
15Close the relay unit cover.
16Remove the two finisher-mount-
ing hooks from the box.
17Remove the main output tray 
and the sub output tray, and then 
unpack them.
18Hold the left and right sides of 
the staple finisher and lift it out of 
the box.
When grabbing the staple 
finisher, be sure to grab 
the areas indicated in the 
illustration.
19Remove the sheet from the sta-
ple finisher.
Downloaded From ManualsPrinter.com Manuals 

Staple Finisher 275
20Remove the packing tape and 
packing materials from the con-
nectors and the outside of the 
staple finisher.
21Open the stapler cover, and then 
remove the tape securing the 
staple cartridge.
22Use a coin to remove the cover 
(two locations) on the left side of 
the machine.
Downloaded From ManualsPrinter.com Manuals 

Staple Finisher 276
23Secure the two mounting hooks 
on the staple finisher to the left 
side of the machine.
24Align the side of the relay unit 
with that of the staple finisher, 
and then hook them onto the fin-
isher to install them.
When grabbing the staple 
finisher, be sure to grab 
the areas indicated in the 
illustration.
Downloaded From ManualsPrinter.com Manuals