Konica Minolta magicolor 4690MF User Manual

About Duplex Printing 89
About Duplex Printing
Duplex (double-sided) printing can be done with magicolor 4690MF, which 
has the duplex unit built in as a standard. If the paper has low opacity (high 
translucency), then the printed data from one side of the page will show 
through to the other side. Check your application for margin information. For 
best results, print a small quantity to make sure the opacity is acceptable.
Note
Only plain paper, 60–90 g/m2 (16–24 lb bond) can be autoduplexed. See...

About Duplex Printing 90
In addition, if “Combination” has been set to “Booklet”, autoduplex printing is 
performed.
The following Order settings are available when “Booklet” is selected.
1Load plain paper into the tray.
2From the printer driver, specify duplex (double-sided) printing (Layout tab 
in Windows).
3Click OK.
With autoduplexing, the back side is printed first, and then the front 
side is printed.If “Left Binding” is selected, the pages can be folded as a 
left-bound booklet.
If “Right...

Output Tray 91
Output Tray
All media is fed out facing down into the output tray on the left side of the 
machine. This tray has a capacity of approximately 250 sheets (A4/Letter) of 
80 g/m
2 paper.
If the media is stacked too high in the output tray, your machine may 
experience media misfeeds, excessive media curl, or static buildup. 
Remove transparencies as soon as possible from the output tray to 
avoid static buildup
The output tray can be pulled out to 
be extended. Adjust the output tray...

Media Storage 92
Media Storage
„Keep media on a flat, level surface in its original wrapper until it is time to
load it.
Media that has been stored for a long time out of its packaging may dry up 
too much and cause misfeeding.
„If media has been removed from its wrapper, place it in its original pack-
aging and store in a cool, dark place on a level surface.
„Avoid moisture, excessive humidity, direct sunlight, excessive heat (above 
35°C [95°F]), and dust 
„Avoid leaning against other objects or...

Original Media 93
Original Media
Specifications
Documents that can be placed on the original glass
The following types of documents can be placed on the original glass.
Observe the following precautions when placing a document on the original 
glass.
„Do not place objects weighing more than 3 kg (6.6 lb) on the original 
glass; otherwise the glass may be damaged.
„Do not press down extremely hard on a book spread on the original glass; 
otherwise the original glass may be damaged.
Documents that can be...

Original Media 94
„Documents with pages that have had cutouts removed or are cutouts
„Label sheets
„Offset printing masters
„Documents with binder holes
Downloaded From ManualsPrinter.com Manuals 

Loading a Document to be Copied 95
Loading a Document to be Copied
Placing a document on the original glass
1Lift to open the ADF cover.
2Position the document on the 
original glass.
Align the document with 
the arrow on the left side 
toward the rear of the 
machine.
Document
Downloaded From ManualsPrinter.com Manuals 

Loading a Document to be Copied 96
3Gently close the ADF cover.
Loading a document into the ADF
1Put the document into the ADF 
document feed tray face up.
Before loading a docu-
ment into the ADF, check 
that no document pages 
remain on the original 
glass.
2Adjust the document guides to 
the document size.
Document
Downloaded From ManualsPrinter.com Manuals 

4Using the Printer
Driver
Downloaded From ManualsPrinter.com Manuals 

Selecting Printer Driver Options/Defaults (for Windows) 98
Selecting Printer Driver Options/Defaults 
(for Windows)
Before you start working with your machine, you are advised to verify and 
change the default printer driver settings if necessary. Also, in case you have 
options installed, you should “declare” the options in the printer driver.
1Choose the driver’s properties as follows:
– (Windows Vista)
From the Start menu, select Control Panel, and then click Hardware 
and Sound to select Printers....