Konica Minolta bizhub 420 User Manual

Utility 16
bizhub 500/420/360 (Phase 3) 16-69
3Touch the desired item to highlight it, then select [Allow] or [Restrict] in 
the right side area of the screen.
4If further changes are required, touch the desired key.
Downloaded From ManualsPrinter.com Manuals 

16Utility 
16-70 bizhub 500/420/360 (Phase 3)7 Expert Adjustment>1 Original Image Density
Shift the nine density levels that can be selected manually on the Basic 
Screen to three levels lighter or three levels darker.
This function can be applied to each of three original image types (Photo, 
Text, Dot Matrix) in addition to the regular setting (Text/Photo).
1Follow the procedure described in How to access the Administrator 
Setting Screen on page 16-3 to display the Administrator Setting 
Screen....

Utility 16
bizhub 500/420/360 (Phase 3) 16-71The Original Image Density Screen will be displayed.
3Touch either [Copy] or [Fax] under Function in the left side area of the 
screen.
4Select the original type to be adjusted in the center of the screen, then 
touch [Light] or [Dark] in the right side area of the screen to specify the 
desired adjustment level.
– Repeat this step to make an adjustment for each original type.
5Touch [OK] to complete the setting.
– To cancel the change, touch [Cancel].
In...

16Utility 
16-72 bizhub 500/420/360 (Phase 3)7 Expert Adjustment>2 Erase Adjustment
Specify the conditions in operating the Non Image Area Erase function, and 
also specify the erase amount of the ADF Frame Erase function.
1Follow the procedure described in How to access the Administrator 
Setting Screen on page 16-3 to display the Administrator Setting 
Screen.
2Touch [1 System Setting], [7 Expert Adjustment], and then [2 Erase 
Adjustment].
The Erase Adjustment Screen will be displayed.
Downloaded From...

Utility 16
bizhub 500/420/360 (Phase 3) 16-73
3Select the condition to operate the Non Image Area Erase function.
– Touch [Non Image Area Erase] to display the Non Image Area Erase 
Screen.
– Select the desired condition to operate this function.
[Always]: No condition is specified.
[Only when Auto Size or ×1.0 is selected]: Operates only when Auto 
Size or e1.0 magnification ratio is selected.
[Do Not Erase when ×1.0 is selected]: Operates when any 
magnification ratio except e1.0 is specified.
– Touch...

16Utility 
16-74 bizhub 500/420/360 (Phase 3)
4Select the desired operation of Non Image Area Erase function.
– Touch [Non Image Area Erase Setting] to display the Non Image 
Area Erase Setting Screen.
– Select the desired machine operation of this function.
[Auto]: Erases automatically.
[Specify]: Erase type and original density specified on this screen 
will be applied. Five levels are provided to adjust the original 
density.
– Specify the erase type and original density.
Touch either [Diagonal Erase]...

Utility 16
bizhub 500/420/360 (Phase 3) 16-75
5Select the condition to operate the ADF Frame Erase function.
Select whether or not to operate this function whenever using ADF, and 
also specify the erase amount.
– Touch [ADF Frame Erase] to highlight it, then specify the desired 
erase amount using [+] and [–] under Job Setting in the right side 
area of the screen.
Available range is 1 to 5 mm. Over 5 mm of the erase amount 
cannot be specified.
– To disable this function, specify 0 mm as erasure...

16Utility 
16-76 bizhub 500/420/360 (Phase 3)7 Expert Adjustment>3 Finisher Adjustment
Use this function to make the following adjustments for finisher options.
Adjustment menu items may differ depending upon the configuration of the 
machine options being installed.
0Perform Center Staple Position and Half-Fold Position for the machine 
with Finisher FS-510 and Saddle stitcher SD-502 installed.
0Perform Punch Horizontal Position and Punch Resist Loop Size for the 
machine with Finisher FS-510 and Punch...

Utility 16
bizhub 500/420/360 (Phase 3) 16-77
1Follow the procedure described in How to access the Administrator 
Setting Screen on page 16-3 to display the Administrator Setting 
Screen.
2Touch [1 System Setting], [7 Expert Adjustment], and then [3 Finisher 
Adjustment].
The Finisher Adjustment Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 

16Utility 
16-78 bizhub 500/420/360 (Phase 3)
3Adjust the dislocation of staple position on each paper size, referring to 
a sample copy made by using Fold & Staple mode.
– Touch [1 Center Staple Position] to display the Center Staple 
Position Screen.
– Select the paper size to be adjusted, then touch [Test Copy].
The Test Copy Screen will be displayed.
– Press [Start] to make a sample copy. When completed, touch 
[Close] to return to the Center Staple Position Screen.
– Compare the page widths of left...