Konica Minolta bizhub 420 User Manual

Application Functions6
bizhub 500/420/360 (Phase 3) 6-109
2
Note 
To release the selected application function, touch [OFF].
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the 
Application Screen or Basic Screen.
Downloaded From...

6Application Functions
6-110 bizhub 500/420/360 (Phase 3)Printing Page Number (Page #)
0Specify the start number. Use a minus value, if required.
For example, enter –1 to set the third page as page 1. Available range for 
this setting is –99999 ~ 99999.
0When Chapters is used in combination, the start number for the first page 
of each chapter can also be specified. Available range for this setting is 
–999 ~ 999.
0Select one from the five types of page number format.
0When Cover Mode is used in...

Application Functions6
bizhub 500/420/360 (Phase 3) 6-111
4Touch [Stamp/Overlay], then touch [Page #].
The Page # Screen will be displayed.
5Specify the start number and page number type.
– Touch [Page #] under Start No., then enter the desired start number 
from the control panel keypad.
Press [1] on the control panel to switch the value from plus to minus 
and vice versa.
– To start the page number from the first page of each chapter, touch 
Chapter to highlight it, then enter the desired start number...

6Application Functions
6-112 bizhub 500/420/360 (Phase 3)– Touch one of the five keys under Page No. Type to highlight it.
– To make settings for printing page number onto covers, proceed to 
the next step.
To change or make fine adjustment on the print position currently 
specified as indicated on the Print Position key, proceed to step 7.
To complete this setting, proceed to step 9.
?Do you want to change the currently entered value using control 
panel keypad?
%Press [C] (Clear) on the control panel,...

Application Functions6
bizhub 500/420/360 (Phase 3) 6-113– Touch [OK] to complete the setting.
7Touch [Print Position] to display the Print Position Screen.
– Touch one of the nine Print Position keys to highlight it.
– If fine adjustment is not required, proceed to step 9.
8Touch [Change Adjustment] to display the Fine-Tune Screen.
– Touch [Left] or [Right] under Left & Right Adjustment to highlight it. 
Use [+] and [–] to enter a fraction in 0.1 mm increments. Touch the 
bidirectional arrow key to move...

6Application Functions
6-114 bizhub 500/420/360 (Phase 3)
?What if the value just entered is out of available range?
%The Input Error message will be displayed. Press [C] (Clear) on the 
control panel, then reenter the correct value.
9Touch [OK] to return to the Application Screen.
– Touch [Cancel] on the Page # Screen, Insert Sheet Setting Screen, 
Print Position Screen, or Fine-Tune Screen to cancel the setting 
change.
10Select additional copy conditions, as desired.
11Press [Start] on the control...

Application Functions6
bizhub 500/420/360 (Phase 3) 6-115Printing Distribution Number (Set Numbering)
0Specify the start number. Available range for this setting is 0 ~ 9999.
The distribution number is normally printed as a four-digit number.
0Select the desired density level from the four options.
0Select whether to print the distribution number on the cover only or on all 
pages.
0Select the character size from 20pt or 36pt.
1Position the original.
2Enter the desired print quantity from the control...

6Application Functions
6-116 bizhub 500/420/360 (Phase 3)
4Touch [Stamp/Overlay], then touch [Set Numbering].
The Set Numbering Screen will be displayed.
5Specify the start number, text density, and pages to print.
– Enter the desired start number from the control panel keypad to 
display it under Start Number.
– Touch one of the four keys under Text Density to highlight it.
– Touch either of the two keys under Pages to highlight it.
– Touch [Character Size] to select 20 point or 36 point.
Downloaded...

Application Functions6
bizhub 500/420/360 (Phase 3) 6-117
?Do you want to change the currently entered value using control 
panel keypad?
%Press [C] (Clear) on the control panel, then enter the correct value.
?What if the value just entered is out of available range?
%The Input Error message will be displayed. Press [C] (Clear) on the 
control panel, then reenter the correct value.
6Touch [OK] to return to the Application Screen.
– Touch [Cancel] on the Set Numbering Screen to cancel the setting...

6Application Functions
6-118 bizhub 500/420/360 (Phase 3)Printing Stamp onto Copies (Built-in Stamp)
0Select one from the eight stamp types provided on the screen.
0The desired print position can be selected from nine areas. If required, 
make fine adjustment of the selected position both in lengthwise and 
widthwise directions by entering a value from 0.1 mm to 50.0 mm in 0.1 
mm increments.
0Select to print the stamp either on the cover or on all pages.
0Select the character size from large size or...