Konica Minolta bizhub 420 User Manual

7Finishing/Folding
Downloaded From ManualsPrinter.com Manuals 

Downloaded From ManualsPrinter.com Manuals 

Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-3
7 Finishing/Folding
7.1 Output for Machine without Finisher
The output tray OT-501 is installed in the 
main unit without a finisher as illustrated 
right. The machine is available to select the 
following four output modes. 
As the default setting, Sort is selected.
-Sort
Select this setting to separate each set of a multi-page original.
-Group
Select this setting to separate the copies of each page in a multi-page 
original.
-Sort and Offset
Select...

7Finishing/Folding
7-4 bizhub 500/420/360 (Phase 3)Function overview
ModeSample
Sort
Group
Sort and Offset
Group and Offset
Downloaded From ManualsPrinter.com Manuals 

Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-5To specify output mode
0As the default setting, Group is selected. When 2 sets or more are 
entered, automatically output in sort mode. 
0Some copy condition is incompatible with Group. For details, see Copy 
Conditions Incompatible with Finishing/Folding on page 7-32.
0If no finisher is installed and the following conditions are met, printed 
copies can be fed out and sorted in an alternating crisscross pattern.
A4- or B5-size paper is used.
Paper of...

7Finishing/Folding
7-6 bizhub 500/420/360 (Phase 3)
5Select Sort or Group, and set Offset to use offset output.
– To set sort, touch [Sort] to highlight it.
– To set group, touch [Group] to highlight it.
– To set sort in alternating crisscross pattern, touch [Sort] and [Offset] 
to highlight them.
– To set group in alternating crisscross pattern, touch [Group] and 
[Offset] to highlight them.
6Touch [OK].
The Basic Screen will be restored.
7Specify any necessary copy settings.
– Auto Paper Select may be...

Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-7
7.2 Output for Machine with Finisher
The machine with Finisher FS-510/FS-511 provides output modes as 
described below.
As factory default, Finisher FS-510 is set to output the printed sheets to tray 
1 in Group mode.
As factory default, Finisher FS-511 is set to output the printed sheets to 
primary tray (tray 2) in Group mode.
-Sort
Select this setting to separate each set of a multi-page original.
-Group
Select this setting to separate the copies of...

7Finishing/Folding
7-8 bizhub 500/420/360 (Phase 3)Function overview
ModeSample
Sort
Group
Sort + Offset
Group + Offset
Downloaded From ManualsPrinter.com Manuals 

Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-9To specify finisher output mode
0As the default setting, Sort is selected. No limit is established in Sort 
mode.
0Some copy conditions are incompatible with Group mode. For details, 
see Copy Conditions Incompatible with Finishing/Folding on 
page 7-32.
0When making copies using postcard, trace, or OHP transparencies on 
the machine with Finisher FS-511 installed, be sure that the Secondary 
(sub) tray is selected as an output tray.
0Each output tray of...

7Finishing/Folding
7-10 bizhub 500/420/360 (Phase 3)– To set Group in offset output, touch [Group] and [Offset] to highlight 
them.
– To cancel the setting, touch the key again to deselect it.
5Touch [OK].
The Basic Screen will be restored.
6Specify any necessary copy settings.
7Press [Start].
The scan/print job will start.
2
Reminder 
Finisher FS-510 trays gradually go up/down while printed materials 
output, depending on the tray selected.With Saddle Stitcher SD-502 or 
Mailbin Kit MT-501, the...