Inter-Tel Imx/Gmx 256 Installation And Field Maintenance Manual

PROGRAMMINGIssue 1, November 1994INTER-TELPRACTICESIMX/GMX 256 INS~TION & MAINTENANCE
FIGURE 5-31. SMDR (SMDR)
.. ‘>‘:j
htput port:ISerial 1 or Serial2
k Output Active?Yes or No
hlls to be recorded in reports:Select all that apply:
All IncomiIlg callsYes or No
All Local callsYes or No
All Toll CallsYes or No
All DISA Calls -Yes or No
All Conference CallsYes or No
All DID CallsYes or No
All Ring-In Diagnostics Yes or No
Suppress 
all absorbed digits?Yes or No
iuppress all but the first toll digit?Yes or...

INTER-TELPRACTICESIMX/GMX 256 DEXALLATlON & MATYTENANCEPROGRAMMINGIssue 1, November 1994
FIGURE 5-32.ERROR REPORTS (ERR)
outpat port:IS&al 1 or Serial21Is output active?
Report all alarms 
[+++I ?Y or N
Y or N
Report all field service diagnostics 
[***I ?
Report 
alI engineering diagnostics [--I?
Lag all SEND messages to history queue?Y or N
Y or N
Y or N
FIGURE 5-33. PASSWORDS (PASS)
Applications Restricted Password:
Applications Unrestricted Password:
Monitor Restricted Password:
Monitor Unrestricted...

PROGRAMMINGlNTER-TELPRACTxcEsIssue 1, November 1994IMX/GMX 256 INS-TION 8z MAINTENANCE
FIGURE 5-34.SERIAL PORT CONFIGURATION (PORT)
serial Port 1:
Enable 
DSR Handshaking:
Enable 
CTS Handshaking:
Baud
Rate(circleone):Yes or No
Yes or No
110300600120024004800960019200
Serial Port 2:
1 Enable DSR Handshaking:1 Yes or NoEnable 
Cl% Handshaking:Yes or NoBaud
Rate(circleone):110300600120024004800960019200
Page 5-234 

INI-ER-TELPRACTICESIMXlGMX 2% INSTALLATION & MAINTENANCEPROGRAMMING
Issue 1, November 1994
FIGURE 5-35.SYSTEM CONFIGURATION (CONF)
Home Area Code:Time Adjustment:
Local Area Codes: 2
-3, -4
1 SLOT 1BOARD TYPE
I 1 I
2I 
4 I
I 5 I
I 11 I
I 
12 I
13
14I 
15 I
I 
l6 I
Page 5-235 

PROGRAMMING
Issue 1, November 1994INTER-TELPRACTICESIMWGMX 256 INSTALLATION & MAINTENANCE
FIGURE 5-35.SYSTEM CONFIGURATION (Continued)
KSC, IDC, and TlC Ciiuits: Fill in the following charts for KSC, DID, and TlC circuit Programming.
K!K Circuits: Indicate whether the circuits in each board are single or dual.
IDC Circuits: Indicate whether the circuits in each board are DID or OPX.
IDC SLOTClRCUlT 1
CIRCUIT 2CIRCUIT sCIRCUIT 4ClRCUlT 5ClRCUlT 6CIRCUK 7ClRCUlT 8
Page 5-236 

PROGRAMMINGIssue 1, November 1994
FIGURE 5-35.SYSTEM CONFIGURATION (Continued)
TlC Circuits: Indicate whether the circuits in each board are loop start, ground start, DID, E&M, or OPX.
9
10
11
12
13
14
15
Page 5-237 

INTER-TELPRACTICESIMX/GMX 256 INSTALLATION & MAINTENANCETROUBLESHOOTINGIssue 1, November 1994
CONTENTS
TROUBLESHOOTING
PAGE1. Introduction.........................................................
2. Troubleshooting 
Checkiist.............................................
3.Light-Emitting Diode (LED) Indications.................................
4.Aiarm Messages And Field Service Diagnostic............................
.
Minor Alarms That Are User Correctable............................
B.Minor Alarms...

~o~LE!3HOOTINGIssue 1, November 1994lNTER-TELPRAcTIcEsIMX/GMX 256 INSTALLATION & MAINTENANCE
(1)Turn OFF the AC power.CAUTION
Always turn OFF the AC POWER before remov-
ing or inserting the RCPU Card.
(6)
Remove the RCPU Card and check to make sure
that all of the components on the card are proper-
ly seated and that no pins are bent.
Wait 10 seconds and re-insert the card.
Turn ON the AC power.
If the CPU ACTIVE LED is still flashing (or if
the problem still persists), measure the following
system...

INTER-TELPRACTICESIMX/GMX 256 INSTALLATION % MAINTENANCETROUBLESHOOTINGIssue 1, November 1994
FIGURE 6-l.LIGHT-EMITTING DIODE (LED) INDICATIONS
LOCATIONILEDIDESCRIPTION
RCPU CardCPU ActiveLit green to show that the main processor is operating proper-
ly. If unlit, system needs repair.
Power AlarmLit red when the system power supply temperature is abnor-
mally high. Unlit when the temperature is normal.Major Alarm
Lit red when a major alarm has occurred. The light goes out
when the problem is corrected....

~OUBLESHOOTINGIssue 1, November 1994INTER-TELPRACTICESIMWGMX 256 IlSbCLATION & MAINTENANCE
FIGURE 6-l.
LIGHTEMITTING DIODE (LED) INDICATIONS (CONT’D)3LOCATION
Inward Dialing
CardLED
Card ActiveDESCRIPTIONLit green to show that the card is co~unicating properly
with the rest of the system. If flashing, record the flash rate
(l-7) and return the card for repair. If unlit, check for improp-
er connection; if still unlit, return the card for repair.Individual
Circuits (l-8)
Unlit when the associated station...