Inter-Tel Glx Installation And Field Maintenance Manual

INTER-TEL PRACTICES 
GLX INSTALLATION & MAINTENANCE INSTALLATION 
Issue 1, 
November 1985 _. 
7. 
INSTALL THEEXPANSION PCB INTO THE KSU 
7.01 The Main Control PCB has circuitry for 3 C.O. lines and 8 
keysets. 
The Expansion PCB adds circuitry for 3 C.O. lines and 
4 keysets, completing the 6 X 12 configuration. 
NOTE: If you are adding the Expansion PCB after the system has 
been installed, turn off the KSU AC power switch (PWR), unplug 
the KSU AC power cord, and unplug the 25-pair station cable and...

INTER-TEL PRACTICES INSTALLATION 
GLX INSTALLATION & MAINTENANCE Issue 1, 
November 1985 
FIGURE 3-8. INSTALL THE EXPANSION PCB 
EXPANSION PCB 
3 CONTROL 
FIGURE 3-9. WALL MOUNT THE KSU 
PCE 
) ‘;..:. 
: ” 
Page 3-16  

INTER-TEL PRACTICES 
INSTALLATION 
GLX INSTALLATION b MAINTENANCE 
Issue 1, 
November 1985 
9. COMPLETE ALL CONNECTIONS FOR THE RSU 
(1) Attach the female connector that is on the 25-pair cable 
on the station block to the male connector on the left 
side of the KSU. 
This completes the keyset connections. 
(2) To complete C.O. line connections from the modular jack 
assemblies mounted next to the KSU, plug the loose end of 
each line cord into the corresponding C.O. jack on the 
KSU. 
Remember, the...

INTER-TEL PRACTICES INSTALLATION 
GLX INSTALLATION h MAINTENANCE Issue 1, 
November 1985 
10. INSTALL THE KEYSETS 
10.01 Ensure that the station loop resistance test has been per- 
formed before installing the keysets. 
(1) Unpack and inspect each keyset for damage. Along with 
the keyset, the box should contain a 6-foot line cord, a 
coiled handset cord, a handset, and a plastic bag of key 
designation tabs. If items are missing or damaged, con- 
tact Inter-Tels Order Processing Department. 
.:1. 
(2)...

INTER-TEL PRACTICES INSTALLATION 
GLX INSTALLATION & MAINTENANCE Issue 1, 
November 1985 
10.02 Optional, keyset equipment: Three optional items can be 
connected to keysets. For information about a headset, refer to 
page 2-12. A data device equipped with a direct-connection modem 
can be connected to an Executive Keyset; refer to page 7-13. 
Refer to page 3-20 for information about a handset amplifier. 
10.03 To wall mount the keysets: 
(1) 
(2) 
(3) 
(4) 
(5) 
(6) Remove the keyset baseplate by...

INTER-TEL PRACTICES INSTALLATION 
GLX INSTALLATION c MAINTENANCE 
Issue 1, 
November 1985 
11. INSTALL lj HANDSET AMPLIFIER 
11.01 
Users may request to have a handset amplifier installed to 
be able to adjust the volume of the receiver. Refer to page 2-12 
for specifications. Install the amplifier as follows: 
(1) Unplug the coiled handset cord from the keyset. 
(2) Plug the coiled handset cord into the amplifier jack 
labeled HANDSET. 
(3) Plug the amplifier line cord (coming from the jack 
labeled...

INTER-TEL PRACTICES 
INSTALLATION 
GLX INSTALLATION & MAINTENANCE 
Issue 1, 
November 1985 
FIGURE 3-12. 
CONNECT THE EXTERNAL EQUIPMENT 
/-KSU 
‘AGE, l/8 IN. PAGING 
f AMPLIFIER 
MUSIC, RCA-TYPE 
PHONO PLUG 
L MUSIC 
SOURCE 
13. CONNECT THE EXTERNAL PAGING EQUIPMENT 
13.01 
A jack on the right side of the KSU is the output for the 
optional external paging equipment. 
Refer to Figure 3-12 above. 
(1) 
(2) 
(3) 
(4) 
(5) 
(6) 
(7) Cut a length of coaxial cable to run from the amplifier 
to the KSU....

INTER-TEL PRACTICES 
GLX INSTALLATION C MAINTENANCE INSTALLATION 
Issue 1, 
November 1985 
14. 
INSTALL BATTERY BACK-UP EQUIPMENT 
14.01 There are three options for installing battery back-up on 
the GLX System, as described on page 2-13. 
14.02 BATTERIES MUST BE FULLY CHARGED AND OF TEE SAHE AMP-HOUR 
RATING AND AGE. 
Since batteries give off explosive and corrosive 
gases, place them in a well-ventilated room and coat the termi- 
nals with an anti-corrosive agent. Check with your back-up power 
~...

INTER-TEL PRACTICES 
GLX INSTALLATION & MAINTENANCE INSTALLATION 
Issue 1, 
November 1985 
B. INSTALL A 30V BATTERY PACK AND BATTERY CHARGER 
(1) Follow steps 1 through 5 on the previous page to form the 
battery pack and make the battery connector. 
(2) Connect a length of 18AWG wire 
1, + II 
terminal to the same s+a 
the +3OV contact. from the battery chargers 
battery terminal used for 
(3) Connect a length of wire from the chargers II-II terminal 
to the same ll- battery terminal used for the +3OV...

INTER-TEL PRACTICES INSTALLATION 
GLX INSTALLATION c MAINTENANCE Issue 1, 
November 1985 
C. INSTALL AN UNINTERRUPTED POWER SOURCE (UPS) UNIT 
(1) Turn the KSU AC power switch (PWR) to the OFF position 
and unplug,the AC power cord. 
(2) Plug the UPS unit into the KSU AC outlet. 
(3) Plug the surge/spike protector into the UPS unit. 
(4) Plug the KSU AC power cord into the surge/spike protec- 
tor. 
(5) Turn the KSU and UPS unit power switches to the ON posi- 
tions. 
::: 
: ‘.. 
; .:: 
Page 3-24 
,