Hughes JVC Projector G1500m Unstructions Manual

							29
ENGLISH
OPERATE
VOL.
PAGE
BACK
PRESET
ZOOMFOCUS
COMPUTERVIDEO
QUICK
ALIGN.AV
MUTING
WT
MENU/ENTER
Basic Operations (Cont.)
¦ For Operating Other Functions
nTo turn off video image and audio sound temporarily
Press the AV MUTING button.
nPress once:
Video image and audio sound turn off (do not come out).
nPress again:
Video image and audio sound come out again.
nTo use the quick alignment function
The quick alignment function is used to automatically adjust (set)
the screen settings of ÒTRACKING, PHASE, H. POS. and V. POS.Ó
of computer system input video.
¥ Use either the remote controlÕs or projector Õs button.
nWhen using the remote control unit:
Press the QUICK ALIGN. button.
nWhen using the projector:
Clear the menu display, and press the projector Õs QUICK
ALIGN. Ò+ 3Ó and ÒÐ 2Ó buttons at the same time.
* During the automatic adjustment, ÒQUICK ALIGNMENTÓ appears
on the screen and disappears automatically after the adjustment
is completed.
Note
¥ This function works only for computer system inputs.
It does not work for AV inputs.
CAUTION
¥ When performing automatic adjustment using the quick
alignment function:
Use a bright, still-picture screen. It may not function correctly on a
dark or motion-picture screen.
If the condition adjusted by using the quick alignment function is not
good, manually adjust TRACKING, PHASE, H. POS. and V. POS.
(see pages 31, 37 and 38).
Remote control unit Projector
Screen display
nRemote control unit
AV MUTING button
QUICK ALIGN.  button
QUICK ALIGN.  buttons
STAND BY
LAMP
TEMP
EMERGENCY
VIDEO
COMPUTER
SETTING
QUICK
ALIGN.
-2
+3
nProjectorÕs button
Remote control unit
AV
MUTING
QUICK
ALIGN.QUICK
ALIGN.
-2
+3
QUICK ALIGNMENT
G1500M  p.26-3399.8.25, 5:10 PM 29 
						

							30
OPERATE
VOL.
PAGE
BACK
PRESET
ZOOMFOCUS
COMPUTERVIDEO
QUICK
ALIGN.AV
MUTING
WT
MENU/ENTER
Basic Operations (Cont.)
nTo display the MAIN menu
The main menu is used to adjust or set the projected video picture
and the projectorÕs condition, etc. (PIXEL CLOCK, POSITION,
PICTURE, SOUND, OPTIONS, SOURCE DECODER and
LANGUAGE). For operating the main menu, refer to pages 34 to
47.
¥ Press the remote controlÕs MENU/ENTER button.
The main menu appears on the screen.
Notes
¥ This button works only for numeric values. It does not work for switching
between ON and OFF.
¥ For items such as PIXEL CLOCK (TRACKING and PHASE), POSITION (H.
POS. and V. POS.), SOUND (TREBLE and BASS), both settings are reset
at the same time.
Remote control unit
Remote control unit
Projector
nRemote control unit
MENU/ENTER button SETTING button
STAND BY
LAMP
TEMP
EMERGENCY
VIDEO
COMPUTER
SETTING
QUICK
ALIGN.
-2
+3
nProjector button
PRESET button
nTo display the SETTING menu
The setting menu is used to make basic adjustments and settings
(TRACKING, PHASE, H. POS., V. POS., FOCUS, ZOOM and
AUDIO-VOL.) of the video picture being projected after installation
(connection) or after inputs are switched. For operating the setting
menu, refer to ÒMaking Basic SettingsÓ on page 31.
¥ Press the projectorÕs SETTING button.
The setting menu is displayed on the screen.
SETTING
MENU/ENTER
Note
¥ To change the menu language displayed
English is set when the projector is shipped from the factory. The language
displayed can be selected from the following six languages: 
(Japanese), ENGLISH, DEUTSCH (German), ESPA„OL (Spanish),
ITALIANO (Italian), and FRAN‚AIS (French). However, some words such
as ÒQUICK ALIGNMENTÒ are displayed only in English. Pronouns such as
line display and source display are similarly treated.
nTo use the remote controlÕs PRESET button
The PRESET button is used for adjustments made on the main
menu or setting menu.
¥ When resetting only the selected settings to the factory-set
values, press the remote controlÕs PRESET button.
Only the selected itemÕs setting is reset to the factory-set value.
PRESET
G1500M  p.26-3399.8.25, 5:10 PM 30 
						

							31
ENGLISH
        SETTING
TRACKING                   
PHASE                        
H.POS.                        
V.POS.                        
FOCUS                  –     
ZOOM                   W    
AUDIO -VOL.                
0
0
0
0
+
T
0
Operating the Setting Menu
Making Basic Settings
nProjectorÕs buttons
SETTING button
QUICK ALIGN.  buttons
nSetting menu
Description of adjustment and setting items
TRACKING :If wide vertical stripes appear on the screen,
adjust the lateral video size and display area
so that they disappear. (Ð255 « 0 « +255)
PHASE :If characters on the screen flicker or become
dim, adjust so they become clear.
(Ð127 « 0 « +127)
H. POS. :If the screen position is displaced to the right
or left, adjust the horizontal position of the
screen. (Ð255 « 0 « +255)
V. POS. :If the screen position is displaced upward or
downward, adjust the vertical position of the
screen. (Ð120 « 0 « +120)
FOCUS :Adjust the focus of video picture.
Ð: Focuses on near points.
+: Focuses on farther points.
ZOOM :Adjust the screen size (angle of view).
T : Becomes smaller. (Approx. Ð2%)
W : Becomes larger. (Approx. +2%)
AUDIO-VOL. :Adjust the sound level.
(0 « 50)
EMERGENCY
VIDEO
COMPUTER
SETTING
QUICK
ALIGN.
-2
+3
Here, we make basic video adjustment and sound volume
adjustment which are set up after installation (connection).
Notes
¥ This adjustment menu (setting menu) can be displayed with only the
projectorÕs button. After displaying the setting menu, you can select
or set (adjust) items with cursor buttons on the remote control unit.
¥ If settings and connections are changed, adjust and set those items
again.
¥ After this adjustment (setting menu), if video picture adjustment is
necessary by using the devices connected, perform the details setting
and adjustment on the main menu (pages 34 to 47).
¥ For computer-related inputs, use of the quick alignment function
allows automatic adjustment of TRACKING, PHASE, H. POS. and
V. POS. (See pages 31, 37 and 38).
1Press the SETTING button of the
projector.
¥ The setting menu is displayed on the screen.
2Press the SETTING button to
select the desired item.
¥ The selected item is shown in magenta color. Each time
you press the button, the selected item changes as
follows:
TRACKING
PHASE H. POS. V. POS.
Menu clearing AUDIO-VOL. ZOOM
FOCUS
Memo
To select items using the remote control unit:
Items can be selected using the cursor buttons 5 (backward) or
°(forward) on the remote control unit. In this case, menu clearing in
the above order is not available. The selection changes from AUDIO-
VOL to TRACKING directly.
3Adjust and set the selected item
using the QUICK ALIGN. buttons
+3or Ð2.
¥ To adjust and set multiple items, repeat steps 2 and 3.
¥ To reset the adjustment value of the selected item
(TRACKING, PHASE, H. POS. or V. POS.) to the
factory-set value, press the remote controlÕs PRESET
button. This button does not work for focus, zoom or
sound volume.
Memo
To adjust and set items using the remote control unit:
Items can be adjusted and set using the cursor buttons 2 or 3 on the
remote control unit.
4Clear the setting menu by
pressing the SETTING button
repeatedly.
Memo
To clear the setting menu using the remote control unit:
You can also clear the setting menu by pressing the PAGE BACK
button on the remote control unit.
Memo
Using the quick alignment function:
This function works only for computer-related signals inputted. Press
the remote controlÕs QUICK ALIGN. button, or after clearing the menu
displayed, press the projector Õs QUICK ALIGN. buttons Ò+3Ò and ÒÐ
2Ò at the same time. TRACKING, PHASE, H. POS. and V. POS. are
automatically adjusted.
During the adjustment, ÒQUICK ALIGNMENTÓ appears on the screen,
and disappears after the adjustment finishes. Adjustment ¥ setting level
G1500M  p.26-3399.8.25, 5:10 PM 31 
						

							32
Operating the Main Menu
Configuration the Main Menu (AV Input) For computer inputs, see the following page.
You can adjust video quality (PICTURE), audio quality (SOUND), etc. using the menus.
The menus are configured as follows:
Main menu (AV inputs : During AV IN input signal)
PIXEL CLOCK TRACKING : Normally, no adjustment is required. The lateral size and display area of video image are adjusted.
PHASE : Normally, no adjustment is required. Flickering or dim video image is adjusted.
POSITION V. POS. : The vertical position of the video image being projected is adjusted.
H. POS. : The horizontal position of the video image being projected is adjusted.
PICTURE BRIGHTNESS : The brightness of the video image being projected is adjusted.
CONTRAST : The contrast of the video image being projected is adjusted.
SHARPNESS : The sharpness of the video image being projected is adjusted.
COLOR : The color density of the video image being projected is adjusted.
TINT : The tint of the video image being projected is adjusted. (Displayed only for NTSC signal)
ALL RESET : All the items adjusted are reset.
SOUND TREBLE : The treble of the audio sound being input is adjusted.
BASS : The bass of the audio sound being input is adjusted.
OPTIONS MENU AUTO OFF : Sets whether to turn off menu display automatically (YES) or not (NO).
LINE DISPLAY : Sets whether to make the line display effective (ON) or not (OFF) for about 5 seconds after input
switching.
RIGHT LEFT REV. : Video image is reversed right-to-left (for upside-down hanging (ceiling)).
TOP BOTTOM INV.: Video image is inverted top-to-bottom (for upside-down hanging (ceiling)).
CLAMP : Sets the clamp pulseÕs position at the back porch (BP) or on the sink tip (ST). Normally, the clamp
pulse is used at BP. If, with some PCs or workstations, the screen becomes unstable such as
being too dark or too bright, try to switch to ST.
RESIZE : Does not work with AV (video) input. (RESIZE is shown in gray.)
BACK COLOR : Specifies the background color when there is no video signal. Background color can be selected
from BLUE, CYAN, BLACK, GREEN, MAGENTA, RED, and YELLOW.
COLOR TEMP. : Adjusts the color temperature of the image being projected. Make adjustment when the image
becomes reddish or bluish.
Color temperature can be set to LOW, MIDDLE, or HIGH.
ASPECT CHANGE: Selects the vertical-to-horizontal ratio of the image projected. The factory-set ratio is 4 : 3. When
projecting high-vision video image, a ratio of 16 : 9 can be selected.
SLEEP  TIME : Sets the length of sleep time. A set sleep time after input signal is depleted, the projector goes into
a stand-by state. Sleep time can be selected from 10 minutes, 20 minutes, 30 minutes, and 60
minutes.
LAMP TIME : Indicates the accumulated used hours of the light-source lamp.
SOURCE : Normally used in AUTO. If use in AUTO is unstable such as color not appearing, the screen being disturbed or the
screen being intermitted, set to the dedicated source (forced mode) in accordance with the input signal.
DECODER : Normally, set to AUTO. The color system of an input signal is automatically identified and shown in ( ). When use
in AUTO is unstable such as no color being shown, set the dedicated color system in accordance with the input
signal. You can select from AUTO, NTSC(480i), NTSC4.43, PAL, and SECAM.
LANGUAGE : Text on the screen can be changed to a language other than English. Languages that can be displayed are the
following six : 
 (Japanese), ENGLISH, DEUTSCH (German), ESPA„OL (Spanish), ITALIANO (Italian), and
FRAN‚AIS (French). However, some text such as ÒQUICK ALIGNMENTÓ, etc. are shown only in English.
G1500M  p.26-3399.8.25, 5:10 PM 32 
						

							33
ENGLISH
Operating the Main Menu (Cont.)
Configuration of the Main Menu (Computer-related input)
Main menu (Computer-related inputs : During COMPUTER IN-1 or -2 input signal)
PIXEL CLOCK TRACKING : The lateral size and display area of video image are adjusted.
PHASE : Flickering or dim video image is adjusted.
POSITION V. POS. : The vertical position of the video image being projected is adjusted.
H. POS. : The horizontal position of the video image being projected is adjusted.
PICTURE BRIGHTNESS : The brightness of the video image being projected is adjusted.
CONTRAST : The contrast of the video image being projected is adjusted.
R-GAIN : The gain in red signal of the video image being projected is adjusted.
G-GAIN : The gain in green signal of the video image being projected is adjusted.
B-GAIN : The gain in blue signal of the video image being projected is adjusted.
TEXT MODE : Adjust easiness for reading text during RESIZE.
ALL RESET : All the items adjusted are reset.
SOUND TREBLE : The treble of the audio sound being input is adjusted.
BASS : The bass of the audio sound being input is adjusted.
OPTIONS MENU AUTO OFF : Sets whether to turn off menu display automatically (YES) or not (NO).
LINE DISPLAY : Sets whether to make the line display effective (ON) or not (OFF) for about 5 seconds after input
switching.
RIGHT LEFT REV. : Image is reversed right-to-left (for upside-down hanging (ceiling)).
TOP BOTTOM INV. : Image is inverted top-to-bottom (for upside-down hanging (ceiling)).
CLAMP : Sets the clamp pulseÕs position at the back porch (BP) or on the sink tip (ST). Normally, the clamp
pulse is used at BP. If, with some PCs or workstations, the screen becomes unstable such as
being too dark or too bright, try to switch to ST.
RESIZE : When the number of pixels (resolution) sought by the video image input is smaller than that
(resolution) of D-ILA device, the video image is then enlarged to a virtually full screen size of D-ILA
device and projected. (Resizing indication)
BACK COLOR : Specifies the background color when there is no image signal. Background color can be selected
from BLUE, CYAN, BLACK, GREEN, MAGENTA, RED, and YELLOW.
COLOR TEMP. : Adjusts the color temperature of the video image being projected. Make adjustment when the
video image becomes reddish or bluish.
Color temperature can be set to LOW, MIDDLE, or HIGH.
ASPECT CHANGE : Selects the vertical-to-horizontal ratio of the video image projected. The factory-set ratio is 4 : 3.
When projecting high-vision image, a ratio of 16 : 9 can be selected.
SLEEP TIME : Sets the length of sleep time. A set sleep time after input signal is depleted, the projector goes into
a stand-by state. Sleep time can be selected from 10 minutes, 20 minutes, 30 minutes, and 60
minutes.
LAMP TIME : Indicates accumulated used hours of the light-source lamp.
SOURCE : Normally used in AUTO. If use in AUTO is unstable such as color not appearing, the screen being disturbed or the
screen being intermitted, set to the dedicated source (forced mode) in accordance with the input signal.
DECODER : Does not work with computer-related inputs. (The color system is indicated in gray.)
LANGUAGE : Text on the screen can be changed to a language other than English. Languages that can be displayed are the
following six : 
 (Japanese), ENGLISH, DEUTSCH (German), ESPA„OL (Spanish), ITALIANO (Italian), and
FRAN‚AIS (French). However, some text such as ÒQUICK ALIGNMENTÓ, etc. are shown only in English.
Normal
Text 1
Text 2: Normal
: Display the outline of small letters already.
: Makes the outline of large letters sharp.
G1500M  p.26-3399.8.25, 5:10 PM 33 
						

							34
VIDEO                   AUTO(NTSC(480i))
                 PIXEL CLOCK
                 POSITION
                 PICTURE
                 SOUND
                 OPTIONS
                 SOURCE
       DECODER
       LANGUAGE 
AUTO(NTSC(480i))
ENGLISH
OPERATE
VOL.
PAGE
BACK
PRESET
ZOOMFOCUS
COMPUTERVIDEO
QUICK
ALIGN.AV
MUTING
WT
MENU/ENTER
MENU/ENTER
button
Cursor buttons
PAGE BACK button
Operating the Main Menu (Cont.)
Operating the Main Menu (Basic Operation of the Main Menu)
Submenu items
Input line Source
Decoder (color system) Language
For projector Õs menus, the setting menu and the main menu are
available.
Here, we explain about the operation of the main menu. (see pages
34 to 47)
For the setting menu, refer to ÒMaking Basic SettingsÓ on page 31.
1Press the MENU/ENTER button.
¥ The main menu is displayed on the screen.
2Select an item with the cursor button
5 or °.
¥ The selected item (displayed text) is shown in magenta color
on the screen.
3Set (adjust) the item.
nWhen you have selected DECODER or LANGUAGE,
¥ Set it with the cursor button 2 or 3.
* To finish the main menu, press the PAGE BACK button.
nWhen you have selected an item on the submenu,
¥ Press the MENU/ENTER button to display the submenu, then
set (adjust) the item with the cursor buttons 2 / 3 or 5 / °.
* To return to the main menu, press PAGE BACK again. (To
finish the main menu from the submenu, press PAGE BACK
twice.)
nAbout main menu display:
Line display:The selected input-mode designation is
displayed. For input-mode designation, ÒY/
CÓ, ÒVIDEOÓ, ÒY, P
B/B-Y, PR/R-YÓ,
ÒCOMPUTER 1Ó and ÒCOMPUTER 2Ó are
available.
Source display:The type of signal being input is displayed.
With this projector, unique designations are
previously given to specific horizontal and
vertical frequencies. This allows the source
selected under SOURCE (submenu item) to
be indicated. The source setting can be
selected from AUTO mode and dedicated
(forced) modes. When AUTO is selected, the
horizontal and vertical frequencies of a
signal being input are detected and the
matched designation is displayed in (  ).
Display example: ÒAUTO (NTSC(480i))Ó
Therefore, be careful as the source display
does not always correspond to the indication
or type of the input signal.
For the unique designations for the specific
horizontal and vertical frequencies, see
pages 19 and 46.
Submenu item display:
PIXEL CLOCK : See page 37.
POSITION : See page 38.
PICTURE : See pages 39~41.
SOUND : See page 42.
OPTIONS : See pages 43~45.
SOURCE : See pages 46 and 47.
Decoder (Color system) display :See page 35.
Languag e display :See page 36.
nRemote control unit
nMain menu
(Example: During video signal input)
G1500M  p.34-4599.8.25, 1:13 PM 34 
						

							35
ENGLISH
OPERATE
VOL.
PAGE
BACK
PRESET
ZOOMFOCUS
COMPUTERVIDEO
QUICK
ALIGN.AV
MUTING
WT
MENU/ENTER
MENU/ENTER
button
Cursor buttons
PAGE BACK button
Operating the Main Menu (Cont.)
Changing the Color System
Color system (DECODER) display
AUTO is set for the color system when the projector is shipped from
the factory. Normally, use it in AUTO. If operation in AUTO is unstable
such as with color not being shown, set to a dedicated color system
in accordance with the color system of the signal being input.
1Press the MENU/ENTER button.
¥ The main menu is shown on the screen.
2Select ÒDECODERÓ with the cursor
button 5 or °.
¥ The selected item (displayed in text) is shown in magenta color
on the screen.
3Set the color system with the cursor
button 2 or 3.
¥ Each time you press the cursor button 2 or 3, the color system
changes as follows.
3 : Forward   /   2 : Backward
AUTO ...................Normally, set to AUTO. The color
system of a signal being input is
automatically identified.
NTSC(480i) .......... Dedicated to NTSC(480i).
NTSC4.43 ............ Dedicated to NTSC4.43.
PAL ...................... Dedicated to PAL.
SECAM ................ Dedicated to SECAM.
Memo
About automatic signal identification
¥ AUTO is selected when shipped from the factory. In AUTO, the color system
(DECODER) of the signal being input is automatically identified and indicated
in (  ). Refer to the main menu display.
¥ If operation in AUTO is unstable such as with color not being shown, set to a
dedicated color system in accordance with the color system of the signal
being input. When the dedicated color system is set, be careful as automatic
identification does not work.
¦To finish the main menu, press the PAGE BACK
button.
nRemote control unit
nMain menu
Note
¥ When computer-related signal is input, the display of the
color system is changed to gray color, making operation
impossible. When video signals from AV devices are input,
the item for the color system can be set.
VIDEO                             NTSC(480i)
                 PIXEL CLOCK
                 POSITION
                 PICTURE
                 SOUND
                 OPTIONS
                 SOURCE
       DECODER
       LANGUAGE 
AUTO(NTSC(480i))
ENGLISH
G1500M  p.34-4599.8.25, 1:13 PM 35 
						

							36
OPERATE
VOL.
PAGE
BACK
PRESET
ZOOMFOCUS
COMPUTERVIDEO
QUICK
ALIGN.AV
MUTING
WT
MENU/ENTER
MENU/ENTER
button
Cursor buttons
PAGE BACK button
Operating the Main Menu (Cont.)
Changing the Language Display
Language display
The language in the menu display is set to English when shipped
from the factory. When you want to change to another language, set
it as follows.
1Press the MENU/ENTER button.
¥ The main menu is shown on the screen.
2Select ÒLANGUAGEÓ with the cursor
button 5 or °.
¥ The selected item (displayed in text) is shown in magenta color
on the screen.
3Set the desired language with the
cursor button 2 or 3.
¥ Each time you press the cursor button 2 or 3, the selected
language changes as follows.
3 : Forward   /   2 : Backward
............ Japanese
............ English
............ German
............ Spanish
............ Italian
............ French
Memo
About language display
English is selected when the projector is shipped from the factory. The
languages in the menu display are the following six : 
 (Japanese),
ENGLISH, DEUTSCH (German), ESPA„OL (Spanish), and FRAN‚AIS
(French).
However, some text such as ÒQUICK ALIGNMENTÓ is displayed only in English.
Unique designations such as line display and source display are similarly
indicated.
¦To finish the main menu, press the PAGE BACK
button.
nRemote control unit
nMain menu
Note
¥ The selected item is shown in magenta color. Items shown
in gray cannot be operated or set in the current mode.
VIDEO                             NTSC(480i)
                 PIXEL CLOCK
                 POSITION
                 PICTURE
                 SOUND
                 OPTIONS
                 SOURCE
       DECODER
       LANGUAGE 
AUTO(NTSC(480i))
ENGLISH
G1500M  p.34-4599.8.25, 1:14 PM 36 
						

							37
ENGLISH
OPERATE
VOL.
PAGE
BACK
PRESET
ZOOMFOCUS
COMPUTERVIDEO
QUICK
ALIGN.AV
MUTING
WT
MENU/ENTER
MENU/ENTER
button
Cursor buttons
PAGE BACK button
Operating the Main Menu (Cont.)
Adjusting the Pixel Clock
Submenu item (PIXEL CLOCK)
The pixel clock should be adjusted mainly for computer-related inputs.
(Normally, it does not need to be adjusted for video inputs.) If a wide
stripe appears on the screen, adjust the lateral size of video image
and the display area (tracking adjustment) so the stripe disappears.
Also, if text on the video screen appears flickering or dim, make
adjustment so it becomes clear (phase adjustment).
1Press the MENU/ENTER button.
¥ The main menu appears on the screen.
2Select ÒPIXEL CLOCKÓ with the cursor
button 5 or °.
¥ The selected item (displayed in text) is shown in magenta color
on the screen.
3Press the MENU/ENTER button.
¥ The submenu items of the PIXEL CLOCK menu appears on the
screen.
(PIXEL CLOCK menu)
4Adjust ÒTRACKINGÓ and ÒPHASEÓ with
the cursor buttons.
¥ Adjust the tracking and phase of the video screen being
projected. To adjust the phase, first check for correct tracking
adjustment.
* To reset to the factory-set adjustment values, press the remote
controlÕs PRESET button.
Tracking and phase are reset to the factory-set adjustment values.
¦To return to the main menu, press the PAGE
BACK button. To finish the main menu, press
PAGE BACK again.
¥ To finish the menu display from the submenu display (PIXEL
CLOCK menu), press PAGE BACK twice.
The screen shrinks laterally (right-to-left). (Ð255 ¬ 0 ¬ +255)
The screen extends laterally
(right-to-left). (Ð255 ® 0 ® +255)
Set to a position where text
appears clear.
(Ð127 ® 0 ® +127)
(Ð127 ¬ 0 ¬ +127)
Adjustment item Button Adjustment content
TRACKING
PHASE2
3
5
°
nRemote control unit
nMain menu
Notes
¥ The selected item is shown in magenta color. Items shown
in gray color cannot be operated or set in the current mode.
¥ A dim screen could be caused by insufficient adjustment of
brightness and contrast. Before adjusting phase, make sure
that brightness and contrast are correctly adjusted.
           PIXEL CLOCK
TRACKING      PHASE
               0              0
          PIXEL CLOCK
          POSITION
          PICTURE
          SOUND
          OPTIONS
          SOURCE
DECODER AUTO(       )
LANGUAGE ENGLISH
 COMPUTER1                     SXGA2
G1500M  p.34-4599.8.25, 1:14 PM 37 
						

							38
OPERATE
VOL.
PAGE
BACK
PRESET
ZOOMFOCUS
COMPUTERVIDEO
QUICK
ALIGN.AV
MUTING
WT
MENU/ENTER
MENU/ENTER
button
Cursor buttons
PAGE BACK button
Adjusting the Screen Position
Submenu item (POSITION)
Adjust the position of the screen if it is displaced.
1Press the MENU/ENTER button.
¥ The main menu appears on the screen.
2Select ÒPOSITIONÓ with the cursor
button 5 or °.
¥ The selected item (displayed in text) is shown in magenta color
on the screen.
3Press the MENU/ENTER button.
¥ The submenu items of the POSITION menu appear on the
screen.
(POSITION menu)
4Adjust ÒH. POS.Ó and ÒV. POS.Ó with the
cursor buttons.
¥ Adjust the horizontal and vertical positions of the video picture
screen being projected.
* To reset to the factory-set adjustment values, press the remote
controlÕs PRESET button. H. POS. and V. POS. are reset to the
factory-set adjustment values.
¦To return to the main menu, press the PAGE
BACK button. To finish the main menu, press
PAGE BACK again.
¥ To finish the menu display from the submenu display (POSITION
menu), press PAGE BACK twice.
The screen moves to the left.(Ð255 ¬ 0 ¬ +255)
The screen moves to the right.
(Ð255 ® 0 ® +255)
The screen moves upwards.
(Ð120 ® 0 ® +120)
The screen moves downwards.
(Ð120 ¬ 0 ¬ +120)
Adjustment item Button Adjustment content
H. POS.
V. POS.2
3
5
°
Operating the Main Menu (Cont.)
nRemote control unit
nMain menu
Note
¥ The selected item is shown in magenta color. Items shown
in gray color cannot be operated or set in the current mode.
           POSITION
   H.POS.         H.POS.
             0                  0
  VIDEO                              NTSC(480i)
                   PIXEL CLOCK
                   POSITION
                   PICTURE
                   SOUND
                   OPTIONS
                   SOURCE
         DECODER
         LANGUAGE 
AUTO(NTSC(480i))
ENGLISH
G1500M  p.34-4599.8.25, 1:14 PM 38