HP Officejet Pro 8600 Premium User Manual

							Tray TypeWeightCapacity
(25 mm or 1.0 inch
stacked)
Duplexer Plain and brochure 60 to 105 g/m
2
(16 to 28 lb bond)Not applicable
Output tray All supported media   Up to 150 sheets of plain paper (text
printing)
Automatic
Document
Feeder All supported media except
photo paper
60 to 90 g/m
2
(16 to 24 lb bond)
long grain media onlyHP Officejet Pro 8600:
Up to 35 sheets of plain
paper (5 mm or 0.19
inches stacked)
HP Officejet Pro 8600
Plus and HP Officejet
Pro 8600 Premium: Up
to 50 sheets of plain
paper (11 mm or 0.43
inches stacked)
Set minimum margins
The document margins must match (or exceed) these margin settings in portrait orientation.
122
3
4
1
3
4
Media
(1) Left
margin (2) Right
margin(3) Top
margin (4) Bottom
margin
U.S. Letter
U.S. Legal
A4 3.3 mm (0.13
inch)
3.3 mm (0.13
inch)3.3 mm (0.13
inch) 3.3 mm (0.13
inch)
Windows and
12mm (0.47
(continued)
Printer specifications 167
 
						

							Media(1) Left
margin (2) Right
margin(3) Top
margin (4) Bottom
margin
U.S. Executive
U.S. Statement
8.5 x 13 inch
B5
A5
Cards
Custom-sized media
Photo media inch)
Macintosh
and Linux
Envelopes 3.3 mm (0.13
inch) 3.3 mm (0.13
inch)16.5 mm
(0.65 inch) 16.5 mm
(0.65 inch)
Guidelines for printing on both sides of a page
• Always use media that conforms to the printer specifications. For more information, see
Media specifications.
• Specify two-sided printing options in your application or in the printer driver.
• Do not print on both sides of envelopes, photo paper, glossy media, or paper lighter than 16 lb bond (60 g/m
2) or heavier than 28 lb bond (105 g/m2). Jams might occur with these media
types.
• Several kinds of media require a specific orientation when you print on both sides of a page. These include letterhead, preprinted paper, and paper with watermarks and prepunched
holes. When you print from a computer running Windows, the printer prints the first side of the
media first. Load the media with the print side facing down.
• For auto-duplexing, when printing finishes on one side of the media, the printer holds the media and pauses while the ink dries. Once the ink dries, the media is pulled back into the
printer and the second side is printed. When printing is complete, the media is dropped onto
the output tray. Do not grab it before printing is complete.
• You can print on both sides of supported custom-sized media by turning the media over and feeding it into the printer again. For more information, see 
Media specifications.
Print specifications
Black print resolution
600 x 600 dpi with pigmented black ink
Color print resolution
Up to 4800 x 1200 dpi Optimized on HP Advanced Photo Paper with 1200 x 1200 input dpi
Copy specifications
• Digital image processing
• Up to 99 copies from original (varies by model)
• Digital zoom: from 25 to 400% (varies by model)
• Fit to page, copy preview
Fax specifications
• Walk-up black-and-white and color fax capability.
• Up to 110 speed dials (varies by model).
Appendix A
(continued)
168 Technical information
 
						

							• Up to 120-page memory (varies by model, based on ITU-T Test Image #1 at standardresolution). More complicated pages or higher resolution takes longer and uses more
memory.
• Manual fax send and receive.
• Automatic busy redial up to five times (varies by model).
• Automatic no-answer redial one time (varies by model).
• Confirmation and activity reports.
• CCITT/ITU Group 3 fax with Error Correction Mode.
• 33.6 Kbps transmission.
• 3 seconds per page speed at 33.6 Kbps (based on ITU-T Test Image #1 at standard resolution). More complicated pages or higher resolution takes longer and uses more
memory.
• Ring detect with automatic fax/answering machine switching.
  Photo (dpi) Very Fine (dpi) Fine (dpi) Standard (dpi)
Black 196 x 203 (8-bit grayscale) 300 x 300 196 x 203 196 x 98
Color 200 x 200 200 x 200 200 x 200 200 x 200
Fax to PC Specifications
• Supported file type: Uncompressed TIFF
• Supported fax types: black-and-white faxes
Scan specifications
• Integrated OCR software automatically converts scanned text to editable text
• Twain-compliant interface (Windows only)
• Resolution: 4800 x 4800 ppi optical
• Color: 24-bit color, 8-bit grayscale (256 levels of gray)
• Maximum scan size from glass:
HP Officejet Pro 8600: 216 x 297 mm (8.5 x 11.7 inches)
HP Officejet Pro 8600 Plus and HP Officejet Pro 8600 Premium: 216 x 356 mm (8.5 x 14
inches)
• Maximum scan size from ADF: 216 x 356 mm (8.5 x 14 inches)
Web Services and HP website specifications
Web Services specifications
An Internet connection using either a wired (Ethernet) or wireless connection.
HP ePrint
• Maximum size of email and attachments: 5 MB
• Maximum number of attachments: 10
NOTE: The printer’s email address must be the only address listed in the “To” line of the
email message.
Supported file types:
 PDF
HTML
 Standard text file formats
Printer specifications 169
 
						

							 Microsoft Word, PowerPoint
 Image files, such as PNG, JPEG, TIFF, GIF, BMP
NOTE:You might be able to use other types of files with HP ePrint. However, HP cannot
guarantee that they correct functionality with the printer because they have not been fully
tested.
Printer Apps
To use certain Printer Apps, you might need to set up an account with a partner website. For more
information, visit 
www.eprintcenter.com.
HP website specifications
• A web browser (either Microsoft Internet Explorer 6.0 or higher, Mozilla Firefox 2.0 or higher, Safari 3.2.3 or higher, or Google Chrome 3.0) with the Adobe Flash plug-in (version 10 or
higher).
• An Internet connection
Environmental specifications
Operating environment
Operating temperature: 5° to 40° C (41° to 104° F)
Operating humidity: 15 to 80% RH non-condensing
Recommended operating conditions: 15° to 32° C (59° to 90° F)
Recommended relative humidity: 20 to 80 % RH non-condensing
Shipping environment
Maximum shipping temperature: -40° to 60° C (-40° to 140° F)
Maximum shipping humidity: 5 to 90% RH non-condensing
Electrical specifications
Power supply
Universal power adapter (internal)
Power requirements
Input voltage: 100 to 240 VAC, 50/60 Hz
Output voltage: +32V/+12V at 1095 mA/170 mA
Power consumption
34 watts printing (Fast Draft Mode); 36 watts copying (Fast Draft Mode)
Acoustic emission specifications
Print in Draft mode, noise levels per ISO 7779
HP Officejet Pro 8600
• Sound pressure (bystander position) LpAm 57 (dBA) (mono Draft print)
• Sound power LwAd 7.1 (BA)
HP Officejet Pro 8600 Plus and HP Officejet Pro 8600 Premium
• Sound pressure (bystander position) LpAm 56 (dBA) (mono Draft print)
• Sound power LwAd 7.0 (BA)
Appendix A
170 Technical information
 
						

							Memory device specifications
This section contains the following topics:
•
Memory card specifications
•
USB flash drives
Memory card specifications
Specifications
• Maximum recommended number of files on a memory card: 2,000
• Maximum recommended individual file size: 12 megapixel maximum, 8 MB maximum (TIFF files, 50 MB maximum)
• Maximum recommended memory card size: 64 GB (solid state only)
NOTE: Approaching any of the recommended maximums on a memory card might
cause the performance of the printer to be slower than expected.
Supported memory card types
• Secure Digital (SD), Mini SD, Micro SD
• High Capacity Secure Digital
• Memory Stick Pro Duo
• Memory Stick Pro Duo
• MultiMediaCard (MMC), MMC Plus, MMC (RS-MMC)
USB flash drives
HP has fully tested the following USB flash drives with the printer:
• Kingston:  Data Traveler 100 USB 2.0 flash drive (4 GB, 8 GB, and 16 GB)
• Lexar JumpDrive Traveller:  1 GB
• Imation:  1 GB USB Swivel
• Sandisk:  Ultra Titanium plus USB Flash Drive 4 GB
• HP: 8 GB HI.SPEED USB flash drive v100w
NOTE: You might be able to use other USB flash drives with the printer. However, HP
cannot guarantee that they correct functionality with the printer because they have not been
fully tested.
Printer specifications 171
 
						

							Regulatory information
The printer meets product requirements from regulatory agencies in your country/region.
This section contains the following topics:
•
FCC statement
•
Notice to users in Korea
•
VCCI (Class B) compliance statement for users in Japan
•
Notice to users in Japan about the power cord
•
Noise emission statement for Germany
•
European Union Regulatory Notice
•
LED indicator statement
•
Gloss of housing of peripheral devices for Germany
•
Notice to users of the U.S. telephone network: FCC requirements
•
Notice to users of the Canadian telephone network
•
Notice to users of the German telephone network
•
Australia wired fax statement
•
Regulatory information for wireless products
•
Regulatory model number
Appendix A
172 Technical information
 
						

							FCC statement
FCC statement
The United States Federal Communications Commission (in 47 CFR 15.105) has specified 
that the following notice be brought to the attention of users of this product. 
This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reason-
able protection against harmful interference in a residential installation.  This equipment 
generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or television reception, which can 
be determined by turning the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures:
•  Reorient the receiving antenna.
•  Increase the separation between the equipment and the receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the  receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.
For further information, contact: Manager of Corporate Product Regulations
Hewlett-Packard Company
3000 Hanover Street
Palo Alto, Ca 94304
(650) 857-1501
Modifications (part 15.21)
The FCC requires the user to be notified that any changes or modifications made to this 
device that are not expressly approved by HP may void the user's authority to operate the 
equipment.
This device complies with Part 15 of the FCC Rules.  Operation is subject to the following 
two conditions:  (1) this device may not cause harmful interference, and (2) this device must 
accept any interference received, including interference that may cause undesired 
operation.
Notice to users in Korea
Regulatory information 173
 
						

							VCCI (Class B) compliance statement for users in Japan
Notice to users in Japan about the power cord
Noise emission statement for Germany
Geräuschemission
LpA < 70 dB am Arbeitsplatz im Normalbetrieb nach DIN 45635 T. 19
European Union Regulatory Notice
Products bearing the CE marking comply with the following EU Directives:
• Low Voltage Directive 2006/95/EC
• EMC Directive 2004/108/EC
• Ecodesign Directive 2009/125/EC, where applicable
CE compliance of this product is valid only if powered with the correct CE-marked AC adapter
provided by HP.
If this product has telecommunications functionality, it also complies with the essential
requirements of the following EU Directive:
R&TTE Directive 1999/5/EC
Compliance with these directives implies conformity to applicable harmonized European
standards (European Norms) that are listed in the EU Declaration of Conformity issued by HP for
this product or product family and available (in English only) either within the product
documentation or at the following website: 
www.hp.com/go/certificates (type the product number
in the search field).
Appendix A
174 Technical information
 
						

							The compliance is indicated by one of the following conformity markings placed on the product:
For non-telecommunications
products and for EU harmonized
telecommunications products, such
as Bluetooth® within power class
below 10mW.
For EU non-harmonized
telecommunications products (If
applicable, a 4-digit notified body
number is inserted between CE
and !).
Please refer to the regulatory label provided on the product.
The telecommunications functionality of this product may be used in the following EU and EFTA
countries: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia,
Spain, Sweden, Switzerland, and United Kingdom.
The telephone connector (not available for all products) is intended for connection to analogue
telephone networks.
Products with wireless LAN devices
Some countries may have specific obligations or special requirements about the operation of
Wireless LAN networks such as indoor use only or restrictions of the channels available. Please
make sure that the country settings of the wireless network are correct.
France
For 2.4-GHz Wireless LAN operation of this product, certain restrictions apply: This product may
be used indoors for the entire 2400-MHz to 2483.5-MHz frequency band (channels 1 to 13). For
outdoor use, only the 2400-MHz to 2454-MHz frequency band (channels 1 to 7) may be used. For
the latest requirements, see 
www.arcep.fr.
The point of contact for regulatory matters is:
Hewlett-Packard GmbH, Dept./MS: HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen,
GERMANY
LED indicator statement
Gloss of housing of peripheral devices for Germany
Regulatory information 175
 
						

							Notice to users of the U.S. telephone network: FCC requirements
Notice to users of the U.S. telephone network: FCC requirements
This equipment complies with FCC rules, Part 68. On this equipment is a label that 
contains, among other information, the FCC Registration Number and Ringer Equivalent 
Number (REN) for this equipment. If requested, provide this information to your telephone 
company.
An FCC compliant telephone cord and modular plug is provided with this equipment. This 
equipment is designed to be connected to the telephone network or premises wiring using 
a compatible modular jack which is Part 68 compliant. This equipment connects to the 
telephone network through the following standard network interface jack: USOC 
RJ-11C.
The REN is useful to determine the quantity of devices you may connect to your telephone 
line and still have all of those devices ring when your number is called. Too many devices 
on one line might result in failure to ring in response to an incoming call. In most, but not 
all, areas the sum of the RENs of all devices should not exceed five (5). To be certain of the 
number of devices you may connect to your line, as determined by the REN, you should call 
your local telephone company to determine the maximum REN for your calling area.
If this equipment causes harm to the telephone network, your telephone company might 
discontinue your service temporarily. If possible, they will notify you in advance. If advance 
notice is not practical, you will be notified as soon as possible. You will also be advised of 
your right to file a complaint with the FCC. Your telephone company might make changes 
in its facilities, equipment, operations, or procedures that could affect the proper operation 
of your equipment. If they do, you will be given advance notice so you will have the 
opportunity to maintain uninterrupted service. If you experience trouble with this equipment, 
please contact the manufacturer, or look elsewhere in this manual, for warranty or repair 
information. Your telephone company might ask you to disconnect this equipment from the 
network until the problem has been corrected or until you are sure that the equipment is not 
malfunctioning.
This equipment may not be used on coin service provided by the telephone company.
Connection to party lines is subject to state tariffs. Contact your state public utility commis-
sion, public service commission, or corporation commission for more information.
This equipment includes automatic dialing capability. When programming and/or making 
test calls to emergency numbers:
• Remain on the line and explain to the dispatcher the reason for the call.
•  Perform such activities in the off-peak hours, such as early morning or late evening .
  Note   The FCC hearing aid compatibility rules for telephones are not applicable 
to this equipment.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a 
computer or other electronic device, including fax machines, to send any message unless 
such message clearly contains in a margin at the top or bottom of each transmitted page 
or on the first page of transmission, the date and time it is sent and an identification of the 
business, other entity, or other individual sending the message and the telephone number 
of the sending machine or such business, other entity, or individual. (The telephone number 
provided might not be a 900 number or any other number for which charges exceed local 
or long-distance transmission charges.) In order to program this information into your fax 
machine, you should complete the steps described in the software.
Appendix A
176 Technical information