HP LaserJet 3055 User Manual

							5.To connect an internal or external modem on a computer, plug one end of a telephone cord into
the all-in-one “telephone” port (the port that is marked with a telephone icon). Plug the other end
of the cord into the modem “line” port.
NOTE Some modems have a second “line” port to connect to a dedicated voice line. If
you have two “line” ports, see your modem documentation to make sure that you connect
to the correct “line” port.
6. To connect a caller-ID box, plug a telephone cord into the previous device’s “telephone” port.
Plug the other end of the telephone cord into the caller-D box “line” port.
7.To connect an answering machine, plug a  telephone cord into the previous device’s “telephone”
port. Plug the other end of the telephone  cord into the answering machine “line” port.
ENWW Connecting additional devices 113
 
						

							8.To connect a telephone, plug a telephone cord into the previous device’s “telephone” port. Plug
the other end of the telephone cord into the telephone “line” port.
9.After you have finished connecting additional devices, plug all of the devices into their power
sources.
114 Chapter 6   Fax ENWW
 
						

							To connect additional devices to the HP LaserJet 3390/3392 all-in-
one
Connect additional devices in the order that is described in the following steps. The output port for
each device is connected to the input port of the next, forming a chain. If you do not want to
connect a specific device, skip the step that explains it and continue to the next device.
NOTE Do not connect more than three devices to the telephone line.
1.Unplug the power cords for all of the devices that you want to connect.
2. If you have not yet connected your all-in-one to a telephone line, see 
Connecting the all-in-one
to a phone line (HP LaserJet 3390/3392 all-in-one)  before proceeding. The all-in-one should
already be connected to a telephone jack.
3. Remove the plastic insert from the telephone port (the port that is marked with the telephone
icon).
ENWW Connecting additional devices 115
 
						

							4.To connect an internal or external modem on a computer, plug one end of a telephone cord into
the all-in-one “telephone” port. Plug the other end of the telephone cord into the modem “line”
port.
NOTE Some modems have a second “line” port to connect to a dedicated voice line. If
you have two “line” ports, see your modem documentation to make sure that you connect
to the correct “line” port.
5. To connect a caller-ID box, plug a telephone cord into the previous devi\
ce’s “telephone” port.
Plug the other end of the telephone cord into the caller-ID box “line” port.
6.To connect an answering machine, plug a  telephone cord into the previous device’s “telephone”
port. Plug the other end of the telephone  cord into the answering machine “line” port.
116 Chapter 6   Fax ENWW
 
						

							7.To connect a telephone, plug a telephone cord into the previous device’s “telephone” port. Plug
the other end of the telephone cord into the telephone “line” port.
8.After you have finished connecting additional devices, plug all of the devices into their power
sources.
9. Close the left side panel, and then close the print-cartridge door. When closing the left side
panel, make sure that the fax cords are routed through the upper notch in the panel.
ENWW Connecting additional devices 117
 
						

							118 Chapter 6   FaxENWW
 
						

							7 Copy
●Starting a copy job
●
Canceling a copy job
●
Adjusting the copy quality
●
Adjusting the lighter/darker (contrast) setting
●
Reducing or enlarging copies
●
Changing the number of copies
●
Changing the copy-collation setting
●
Copying onto media of different types and sizes
●
Copying two-sided documents (HP LaserJet 3050 all-in-one)
●
Copying two-sided documents (HP LaserJet 3052/3055 all-in-one)
●
Using automatic two-sided printing (duplexing) to copy documents (HP LaserJet 3390/3392 all-
in-one)
●
Changing tray selection (HP LaserJet 3390/3392 all-in-one)
●
Copying photos and books (HP LaserJet 3052/3055/3390/3392 all-in-one only)
●
Viewing copy settings (HP LaserJet 3390/3392 all-in-one only)
NOTE Instructions for using the flatbed scanner glass  do not apply to the HP LaserJet 3050
all-in-one. For the HP LaserJet 3050 all-in-one, use the automatic document feeder (ADF).
ENWW 119
 
						

							Starting a copy job
NOTEThere are no fax buttons on the  HP LaserJet 3052 all-in-one. The control panel
shown is the control panel on the HP LaserJet 3055 all-in-one.
120 Chapter 7   Copy ENWW
 
						

							To make copies with the all-in-one, use the following instructions.
1.Load your document into the automatic document feeder (ADF) input tray. Load documents
face-down into the HP LaserJet 3050 all-in-one ADF input tray, or face-up into the HP LaserJet
3052/3055/3390/3392 all-in-one ADF input tray. The ADF is recommended for copying multiple-
page documents.
HP LaserJet 3052/3055
HP LaserJet 3390/3392
HP LaserJet 3050
-or-
Load your document onto the flatbed scanner (HP LaserJet 3052/3055/3390/3392 all-in-one
only). Load documents face-down (one page at a time) with the upper-left corner of the
document located in the lower-right
 corner of the glass.
HP LaserJet
HP LaserJet 3390/33923052/3055
2.
Press  Start Copy on the all-in-one control panel to start copying.
3. Repeat the process for each copy.
For more detailed instructions about loading documents onto the flatbed scanner or into the ADF
input tray, see 
Loading documents to fax, copy, or scan .
NOTE If a document is loaded in the ADF input tray and a document is also on the flatbed
scanner, the all-in-one automatically scans from the ADF.
Canceling a copy job
To cancel a copy job, press Cancel on the all-in-one control panel. If more than one process is
running, pressing  Cancel clears the process that currently appears on the all-in-one control-panel
display.
NOTE If you cancel a copy job, clear the document from the flatbed scanner or from the
automatic document feeder.
ENWW Canceling a copy job 121
 
						

							Adjusting the copy quality
Five copy-quality settings are available: Draft,Text , Mixed , Film photo, and  Picture.
The factory-set default for copy quality is  Text. This setting is the best for items that contain mostly
text.
When making a copy of a photo or graphic, you can select the  Film photo setting for photos or the
Picture  setting for other graphics to increase the  quality of your copy. Select the Mixed setting for
documents that include both text and graphics.
If you want to conserve toner, and the copy quality is not as important, select  Draft.
To adjust the copy quality for the current job
1. On the all-in-one control panel, press  Quality to see the current quality setting for the copy.
2. Use the  < or the  > button to scroll through the quality setting options.
3. Select a setting, and then press  Start Copy to save the selection and immediately start the copy
job, or press 
 to save the selection without starting the job.
NOTE The change in the setting remains active for about two minutes after the copy job
has been completed. During this time,  Settings=Custom appears on the all-in-one
control-panel display.
To adjust the default copy quality
1. On the all-in-one control panel, press  Menu.
2. Use the  < or the  > button to select  Copy setup, and then press 
.
3. Press 
 to select  Default Quality .
4. Use the  < or the  > button to scroll through the choices.
5. Press 
 to save the selection.
122 Chapter 7   Copy ENWW