HP Color LaserJet CM4730 User Manual

2.Adjust the rear media-length guide by squeezing the guide adjustment latch and sliding the back
of the tray to the length of the media you are using.
3.Slide the media-width guides open to the size for the media you are using.
ENWW Load paper and print media 95
 

4.Load media into the tray face up.
NOTE For best performance, fill the  tray completely without splitting the ream of paper.
Splitting the ream can cause a multifeed proble m. The capacity of the paper tray can vary.
For example, if you are using 75 g/m
2 (20 lb) paper, the tray holds a full ream of 500 sheets.
If the media is heavier, the tray will not  hold a full ream. Do not overfill the tray.
NOTEIf the tray is not adjusted correctly, an  error message might appear or the media
might jam.
5. Slide...

CAUTIONDo not print cardstock, enve lopes, heavy or extra heavy paper, or unsupported sizes
of media from the 500-sheet trays. Print on these ty pes of media only from tray 1. Do not overfill
the input tray or open it while it is  in use. Doing so can cause paper jams.
Load custom-size media into tray 2
To use custom media, change the size setting on the control panel to  Custom and set the unit of
measure, X dimension, and Y dimension. See 
Configure a tray to match print job settings  for more...

Configure trays
The MFP automatically prompts you to configure a tray for type and size in the following situations:
●When you load paper into the tray
●When you specify a particular tray or media type for a print job through the printer driver or a
software program and the tray is not configured to match the print-job’s settings
The following message appears on the control panel:Tray  [type] [size] To change size or type,
touch “Modify”. To accept, touch “OK”..
NOTEThe prompt does not appear if you are...

Configure a tray by using the Supplies Status menu
You can also configure the trays for type and size without a prompt from the MFP.
1.Scroll to and touch Supplies Status.
2.Touch the desired tray.
3.Touch Modify.
4.Select the size and type. If you select a custom type, use the numeric keypad to set the X dimension
and the Y dimension, and then touch OK.
5.Touch OK.
6.Touch OK again.
Automatic media type sensing (auto sense mode)
The automatic media type sensor functions only when that tray is configured...

Transparency
●The printer does not stop any pages for sensing but distinguishes between transparencies
(Transparency mode) and paper (Normal mode).
●This is the fastest mode and is useful for high-volume printing in Normal mode.
Tray 2–4 sensing
Expanded sensing
●The printer stops the first five pages fed from each paper tray to sense the type and averages the
five results.
●The printer assumes that the sixth and all subsequent pages are of the same media type, until the
printer is turned off or goes...

Select the output bin
Standard output bins
The MFP has an ADF output bin and the standard output bin for printed pages. 
1Standard output bin
2ADF output bin (for copy originals)
When you scan or copy documents by using the ADF, the originals are automatically delivered to the
ADF output bin. Copies made from the scanner gla ss are delivered to the standard output bin or the
output bin(s) on the stapler/ stacker or the 3-bin mailbox.
When you send print jobs to the MFP from a computer, the output is to...

13–bin mailbox output bins
2ADF output bin (for copy originals)
The top two bins each hold up to 100 sheets of paper. A sensor stops the MFP when a bin is full. MFP
operation continues when you empty or reduce the amount of media in the bin.
The lower bin holds up to 500 sheets of paper.
Select an output location
If possible, select an output location (bin) thr ough your program or driver. Where and how you make
selections depends on your program or driver. If you  cannot select an output location from...

4.Select the Device Settings tab.
5.Use either of the following methods to select the stapler/stacker.
●Scroll down to Automatic Configuration, select Update Now, and click Apply.
●Scroll down to Accessory Output Bin, select HP 500 sheet stapler/stacker or HP 700 Sheet
3-bin Mailbox, and click Apply.
Configure the printer driver to recognize the 3-bin mailbox in Macintosh
1.Open the Printer Center utility.
2.Select HP Color LaserJet CM4730.
3.On the File menu, click on Show Info (command, i).
4.Select...

Select the operating mode in the printer driver (Mac OS X)
1.In the Apple menu, click System Preferences.
2.In the System Preferences box, click Print and Fax.
3.Click Set Up Printers. A Printer List displays.
4.Select the HP product, and then click Show Info on the Printers menu.
5.Select the Installable Options panel.
6.In the Accessory Output Bins list, select HP 3-Bin Mailbox.
7.In the Mailbox Mode list, select the appropriate operational mode, and then click Apply
Changes.
104 Chapter 7   Paper and...