HP Color LaserJet 2700 User Manual
Here you can view all the pages of manual HP Color LaserJet 2700 User Manual. The HP manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 111
6.Open the top cover. 7.If the jammed sheet is visible, remo ve it and then close the top cover. 8.If the sheet is not visible, use the power switch to turn off the printer. WARNING! The fuser will be hot. Wait 10 minutes before proceeding. ENWW Jams 101
Page 112
9.Place your thumbs on the fuser latches, squeeze the latches, and pull up on the fuser to remove it. 10. On the fuser, lift the shutter door. CAUTION Do not open the shutter door while the fuser is in the printer. 11.Remove any jammed sheets. NOTE If the sheet tears, make sure that all fragments are removed before you resume printing. 102 Chapter 8 Problem solving ENWW
Page 113
12.Hold the fuser with your thumbs on the latches, and then push both sides of the fuser into the printer. Press the fuser down until it clicks into place. 13.Close the top cover and then turn on the printer. Jam in output bin For this control-panel message, look in two places for jams. First, check the output bin area for a jam. Next, starting with step 3, check the top cover area. 1.Look for jammed paper in the output bin area. 2. Remove any visible media. NOTE If the sheet tears, make sure that all...
Page 114
3.Open the top cover. 4.If the jammed sheet is visible, remove it and then close the top cover. 5.If the sheet is not visible, use the power switch to turn off the printer. WARNING! The fuser will be hot. Wait 10 minutes before proceeding. 104 Chapter 8 Problem solving ENWW
Page 115
6.Place your thumbs on the fuser latches, squeez e the latches, and pull up on the fuser to remove it. 7. On the fuser, lift the shutter door. CAUTION Do not open the shutter door while the fuser is in the printer. 8.Remove any jammed sheets. NOTE If the sheet tears, make sure that all fragments are removed before you resume printing. ENWW Jams 105
Page 116
9.Hold the fuser with your thumbs on the latches, and then push both sides of the fuser into the printer. Press the fuser down until it clicks into place. 10.Close the top cover and then turn on the printer. 106 Chapter 8 Problem solving ENWW
Page 117
Paper-handling problems Use only media that meets the specifications outlined in the HP LaserJet Printer Family Print Media Specification Guide. For ordering information, see Supplies and accessories. For media specifications for this printer, see Print-media specifications. Printer feeds multiple sheets Cause Solution The paper exceeds the maximum stack-height indicator mark in the tray (trays 2 or 3).Open the tray and verify that the media stack is below the maximum stack-height mark. The paper is...
Page 118
Media does not feed automatically Cause Solution Manual feed is selected in the software program.Load a sheet of media into tray 1 and press OK. The tray is empty.Load media into the tray. Media from a previous jam has not been completely removed.Open the printer and remove any media that is in the paper path. Closely inspect the fuser area for jams. See Jams. The media size is not configured correctly for the tray.Print a configuration page or use the control panel to determine the size for which the...
Page 119
Transparencies or glossy paper will not feed Cause Solution Media in another tray is the same size as the transparencies or glossy paper, and the printer is defaulting to the other tray.Make sure that the tray that contains the transparencies or glossy paper is selected in the software program or printer driver. Use the printer control panel to configure the tray to the type that is loaded. See Configuring trays. The tray that contains the transparencies or glossy paper is not configured correctly for...
Page 120
Output is curled or wrinkled Cause Solution The media was used previously.Do not reuse media. Output is consistently curled. Use the control-panel Service menu to turn on the Less paper curl option. See Service menu. Printer will not perform manual duplexing (2-sided printing) or duplexes incorrectly Cause Solution The printer driver is not set up for 2-sided printing.Configure the printer driver for 2-sided printing. See Opening the printer drivers. The first page is printing on the back of preprinted...