Honeywell 20205 Manual

6 - 21
UPC E0 and UPC E1
Most U.P.C. bar codes lead with the 0 number system.  For these codes, use the 
UPC E0 selection.  If you need to read codes that lead with the 1 number sys-
tem, use the UPC E1 selection.  
Default = On (UPC E0) and Off (UPC E1).
UPC E0 and UPC E1 Expand
UPC E Expand expands the UPC E code to the 12 digit, UPC A format.  Default = Off.
UPC E0 and UPC E1 Addenda Required
When Addenda Required is set to on, the image scanner will only read UPC E 
bar codes that have addenda....

6 - 22
UPC E0 and UPC E1 Addenda Separator
When this feature is on, there is a space between the data from the bar code 
and the data from the addenda.  When turned off, there is no space.  
Default = On.
UPC E0 Check Digit
Check Digit specifies whether the check digit should be transmitted at the end 
of the scanned data or not.  Default = On.
UPC E0 Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the 
beginning of the scanned data, but the unit can be programmed so...

6 - 23
UPC E0 Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC E data.Default = Off for both 2 Digit and 5 Digit Addenda.
EAN/JAN 13

EAN/JAN 13
EAN/JAN 13 Check Digit
This selection allows you to specify whether the check digit should be transmit-
ted at the end of the scanned data or not.  Default = On.
* 5 Digit Addenda Off 5 Digit Addenda On* 2 Digit Addenda Off 2 Digit Addenda On
*  On
Off
Off *  On 

6 - 24
EAN/JAN 13 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 13 data.Default = Off for both 2 Digit and 5 Digit Addenda.
EAN/JAN 13 Addenda Required
When Addenda Required is set to on, the image scanner will only read EAN/
JAN 13 bar codes that have addenda.  Default = Not Required.
EAN/JAN 13 Addenda Separator
When this feature is on, there is a space between the data from the bar code 
and the data from the addenda.  When turned off, there is no space.  
Default = On....

6 - 25
ISBN Translate
This selection causes EAN-13 Bookland symbols to be translated into their 
equivalent ISBN number format. Default = Off.
EAN/JAN 8

EAN/JAN 8
EAN/JAN 8 Check Digit
This selection allows you to specify whether the check digit should be transmit-
ted at the end of the scanned data or not.  Default = On.
*  Off On
*  On
Off
Off *  On 

6 - 26
EAN/JAN 8 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 8 data.Default = Off for both 2 Digit and 5 Digit Addenda.
EAN/JAN 8 Addenda Required
When Addenda Required is set to on, the image scanner will only read EAN/
JAN 8 bar codes that have addenda.  Default = Not Required.
EAN/JAN 8 Addenda Separator
When this feature is on, there is a space between the data from the bar code 
and the data from the addenda.  When turned off, there is no space.  
Default = On.
* 5...

6 - 27
MSI

MSI
MSI Check Character
Different types of check characters are used with MSI bar codes.  You can 
program the image scanner to read  MSI bar codes with Type 10 check 
characters. 
 Default = Validate Type 10, but Don’t Transmit.
When Check Character is set to Validate and Transmit, the image scanner will 
only read MSI bar codes printed with the specified type check character, and will 
transmit this character at the end of the scanned data.
When Check Character is set to 
Validate, but...

6 - 28
Plessey Code

Plessey Code
Plessey Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 4-48.   Minimum Default = 4, Maximum Default = 48.
GS1 DataBar Omnidirectional
< Default All GS1 DataBar Omnidirectional Settings >
On
* Off
Minimum Message Length
Maximum Message Length 

6 - 29
GS1 DataBar Omnidirectional
GS1 DataBar Limited
< Default All GS1 DataBar Limited Settings >
GS1 DataBar Limited
GS1 DataBar Expanded
< Default All GS1 DataBar Expanded Settings >
* On
Off
* On
Off 

6 - 30
GS1 DataBar Expanded
GS1 DataBar Expanded Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 4-74.   Minimum Default = 4, Maximum Default = 74.
GS1 Emulation
The imager can automatically format the output from any GS1 data carrier to 
emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar  
symbol.  GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, 
ITF-14,...