Honeywell 20205 Manual

4 - 3
Step 3.Scan the 2 digit hex value from the Programming Chart inside the back 
cover of this manual or scan 9, 9 for all symbologies.
Your change is automatically saved.
To Add a Carriage Return Suffix to All Symbologies
Scan the following bar code if you wish to add a carriage return suffix to all sym-
bologies at once.  This action first clears all current suffixes, then programs a 
carriage return suffix for all symbologies.
Prefix Selections
Add CR Suffix
All Symbologies
Add Prefix
Clear One...

4 - 4
Suffix Selections
Function Code Transmit
When this selection is enabled and function codes are contained within the 
scanned data, the image scanner transmits the function code to the terminal.  
Charts of these function codes are provided in Supported Interface Keys start-
ing on page 7-3.  When the image scanner is in keyboard wedge mode, the 
scan code is converted to a key code before it is transmitted. 
Default = Enable.
Intercharacter, Interfunction, and Intermessage 
Delays
Some terminals...

4 - 5
Intercharacter Delay
An intercharacter delay of up to 495 milliseconds may be placed between the 
transmission of each character of scanned data.  Scan the Intercharacter 
Delay bar code below, then scan the number of milliseconds and the SAVE bar 
code using the Programming Chart inside the back cover of this manual.
To remove this delay, scan the Intercharacter Delay bar code, then set the 
number of steps to 0.  Scan the SAVE bar code using the Programming Chart 
inside the back cover of this...

4 - 6
Interfunction Delay
An interfunction delay of up to 495 milliseconds may be placed between the 
transmission of each segment of the message string.  Scan the Interfunction 
Delay bar code below, then scan the number of milliseconds and the SAVE bar 
code using the Programming Chart inside the back cover of this manual.
To remove this delay, scan the Interfunction Delay bar code, then set the num-
ber of steps to 0.  Scan the SAVE bar code using the Programming Chart inside 
the back cover of this...

5 - 1
5
Data Formatting
Data Format Editor Introduction
You may use the Data Format Editor to change the image scanner’s output.  For 
example, you can use the Data Format Editor to insert characters at certain 
points in bar code data as it is scanned.  The selections in the following pages 
are used only if you wish to alter the output.  
Default Data Format setting = 
None.
Normally, when you scan a bar code, it is output automatically; however when 
you do a format, you must use a “send” command (see...

5 - 2
Step 4. Code I.D.
In the  Appendix A, find the symbology to which you want to apply the 
data format.  Locate the Hex value for that symbology and scan the 2 
digit hex value from the Programming Chart inside the back cover of 
this manual.
Step 5. Length
Specify what length (up to 9999 characters) of data will be acceptable 
for this symbology.  Scan the four digit data length from the Program-
ming Chart inside the back cover of this manual.  (Note: 50 characters 
is entered as 0050.  9999 is a...

5 - 3
ASCII Conversion Chart (Code Page 1252)on page A-4, and nn is the 
numeric value (00-99) for the number of times it should be sent.)
E9 Send all but the last “nn” characters, starting from the current cursor posi-
tion.  
Syntax = E9nn (nn is the numeric value (00-99) for the number of 
characters that will not be sent at the end of the message.) 
Move Commands
F5 Move the cursor ahead “nn” characters from current cursor position.  Syntax = F5nn  (nn stands for the numeric value (00-99) for the...

5 - 4
ters to be replaced and xx2 defines replacement characters, continuing 
through zz
1 and zz2.
E5 Terminates character replacement.  
Syntax = E5.
FE Compare character in current cursor position to the character “xx.”  If char-
acters are equal, increment cursor.  If characters are not equal, no format 
match.  
Syntax = FExx  (xx stands for the hex value for an ASCII code, see 
ASCII Conversion Chart (Code Page 1252)on page A-4.)
EC Check to make sure there is an ASCII number at the current cursor...

5 - 5
When Data Formatter is required, all input data must conform to an edited for-
mat or the image scanner does not transmit the input data to the host device.
Alternate Data Formats
Alternate formats allow you “single shot” capability to scan one bar code using a 
different data format than your primary format.  When data formats are pro-
grammed (see page 5-1), you must input whether you are programming the pri-
mary format, or an alternate format numbered 1, 2, or 3.
An alternate format is...

5 - 6