Honeywell 20205 Manual

6 - 11
Code 93
< Default All Code 93 Settings >
Code 93
Code 93 Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 0-80.  Minimum Default = 0, Maximum Default = 80.
Code 93 Code Page
Code pages define the mapping of character codes to characters.  If the data 
received does not display with the proper characters, it may be because the bar 
code being scanned was created using a  code page...

6 - 12
Straight 2 of 5 Industrial (three-bar start/stop)

Straight 2 of 5 Industrial
Straight 2 of 5 Industrial Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 1-48.  Minimum Default = 4, Maximum Default = 48.
Straight 2 of 5 IATA (two-bar start/stop)

On
*  Off
Minimum Message Length
Maximum Message Length 

6 - 13
Straight 2 of 5 IATA, continued
Straight 2 of 5 IATA Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 1-48.  Minimum Default = 4, Maximum Default = 48.
Matrix 2 of 5

Matrix 2 of 5
On
*  Off
Minimum Message Length
Maximum Message Length
On
*  Off 

6 - 14
Matrix 2 of 5 Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 1-80.  Minimum Default = 4, Maximum Default = 80.
Code 11

Code 11
Check Digits Required
This option sets whether 1 or 2 check digits are required with Code 11 bar 
codes.  
Default = Two Check Digits.
Minimum Message Length
Maximum Message Length
On
*  Off
One Check Digit
*  Two Check Digits 

6 - 15
Code 11, continued
Code 11 Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 1-80.   Minimum Default = 4, Maximum Default = 80.
Code 128

Code 128
Minimum Message Length
Maximum Message Length
* On
Off 

6 - 16
Code 128, continued
ISBT 128 Concatenation
In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard  
for communicating critical blood information in a uniform manner.  The use of 
ISBT formats requires a paid license. The ISBT 128 Application Specification 
describes 1) the critical data elements for labeling blood products, 2) the current 
recommendation to use Code 128 due to its high degree of security and its 
space-efficient design, 3) a variation of Code 128 that...

6 - 17
Code 128 Function Code Transmit
By default, Code 128 function codes are not transmitted with Code 128 bar 
code data.  However, if you wish to transmit Code 128 function codes with the 
bar code data, scan the Function Codes On bar code, below.
Te l e p e n

Te l e p e n
Telepen Output
Using AIM Telepen Output, the image scanner reads symbols with start/stop 
pattern 1 and decodes them as standard full ASCII (start/stop pattern 1).  When 
Original Telepen Output is selected, the image scanner...

6 - 18
Telepen Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 1-60.   Minimum Default = 1, Maximum Default = 60.
UPC A

UPC A
UPC A Check Digit
This selection allows you to specify whether the check digit should be transmit-
ted at the end of the scanned data or not.  Default = On.
Minimum Message Length
Maximum Message Length
*  On
Off
*  On
Off 

6 - 19
UPC A Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the 
beginning of the scanned data, but the unit can be programmed so it will not 
transmit it.
   Default = On.
UPC A Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC A data.Default = Off for both 2 Digit and 5 Digit Addenda.
UPC A Addenda Required
When Addenda Required is set to on, the image scanner will only read UPC A 
bar codes that have addenda.  Default = Not Required.
Off *...

6 - 20
UPC A Addenda Separator
When this feature is on, there is a space between the data from the bar code 
and the data from the addenda.  When turned off, there is no space.  
Default = On.
UPC-A/EAN-13 with Extended Coupon Code
Use the following codes to enable or disable UPC-A and EAN-13 with Extended 
Coupon Code.  
Default = On.
UPC E

Off *  On
* On
Off