Honeywell 1250g2 Manual

6 - 41
UPC-E0 Number System and Check Digit
UPC-E0 Check Digit
Check Digit specifies whether the check digit should be transmitted at 
the end of the scanned data or not.  Default = Off.
UPC-E0 Leading Zero
This feature allows the transmission of a leading zero (0) at the beginning 
of scanned data.  To prevent transmission, scan Off.  Default = Off.
Check 
Digit Number
System
UPC-E0 sample showing the number system and check digit:
* Off  On
* Off On 

6 - 42
UPC-E0 Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC-E data.
Default = Off for both 2 Digit and 5 Digit Addenda.
UPC-E0 Addenda Required
When Required is scanned, the scanner will only read UPC-E bar codes 
that have addenda.  Default = Not Required.
Addenda Timeout
You can set a time during which the scanner looks for an addenda.  If an 
addenda is not found within this time period, the data can be either trans-
mitted or discarded, based on the setting you are using for...

6 - 43
timeout by scanning the bar code below, then setting the timeout (from 0-
65535 milliseconds) by scanning digits from the Programming Chart, then 
scanning Save.  Default = 100.
Note: The Addenda Timeout setting is applied to all addenda and coupon 
code searches.
UPC-E0 Addenda Separator
When this feature is On, there is a space between the data from the bar 
code and the data from the addenda.  When turned Off, there is no space.  
Default = Off.
UPC-E0 Redundancy
If you are encountering errors...

6 - 44
EAN/JAN-13

EAN/JAN-13 On/Off
Convert UPC-A to EAN-13
When UPC-A Converted to EAN-13 is selected, UPC-A bar codes are 
converted to 13 digit EAN-13 codes by adding a zero to the front.  When 
Do not Convert UPC-A is selected, UPC-A codes are read as UPC-A.
*  On
Off
* Do Not Convert  UPC-A UPC-A Converted to EAN-13 

6 - 45
EAN/JAN-13 Check Digit
This selection allows you to specify whether the check digit should be 
transmitted at the end of the scanned data or not.  Default = On.
EAN/JAN-13 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 
data.  Default = Off for both 2 Digit and 5 Digit Addenda.
EAN/JAN-13 Addenda Required
When Required is scanned, the scanner will only read EAN/JAN-13 bar 
codes that have addenda.  Default = Not Required.
Off *  On
* 5 Digit Addenda Off 5 Digit...

6 - 46
EAN-13 Beginning with 2 Addenda Required
This setting programs the scanner to require a 2 digit addenda only on 
EAN-13 bar codes that begin with a “2.”  The following settings can be pro-
grammed:
Require 2 Digit Addenda:  All EAN-13 bar codes that begin with a “2” 
must have a 2 digit addendum.  The EAN-13 bar code with the 2 digit 
addendum is then transmitted as a single, concatenated bar code.  If a 2 
digit addendum is not found within the Addenda Timeout period, the EAN-
13 bar code is...

6 - 47
Default = Don’t Require 5 Digit Addenda.
EAN-13 Beginning with 378/379 
Addenda Required 
This setting programs the scanner to require any combination of a 2 digit 
addenda or a 5 digit addenda on EAN-13 bar codes that begin with a “378” 
or “379.”  The following settings can be programmed:
Require Addenda:  All EAN-13 bar codes that begin with a “378” or “379” 
must have a 2 digit addenda, a 5 digit addenda, or a combination of these 
addenda.  The EAN-13 bar code with the addenda is then...

6 - 48
EAN-13 Beginning with 414/419 
Addenda Required 
This setting programs the scanner to require any combination of a 2 digit 
addenda or a 5 digit addenda on EAN-13 bar codes that begin with a “414” 
or “419.”  The following settings can be programmed:
Require Addenda:  All EAN-13 bar codes that begin with a “414” or “419” 
must have a 2 digit addenda, a 5 digit addenda, or a combination of these 
addenda.  The EAN-13 bar code with the addenda is then transmitted as a 
single, concatenated bar code....

6 - 49
Default = Don’t Require Addenda.
EAN-13 Beginning with 977 Addenda Required
This setting programs the scanner to require a 2 digit addenda only on 
EAN-13 bar codes that begin with “977.”  The following settings can be pro-
grammed:
Require 2 Digit Addenda:  All EAN-13 bar codes that begin with “977” 
must have a 2 digit addendum.  The EAN-13 bar code with the 2 digit 
addendum is then transmitted as a single, concatenated bar code.  If a 2 
digit addendum is not found within the Addenda Timeout...

6 - 50
Require 5 Digit Addenda:  All EAN-13 bar codes that begin with “978” 
must have a 5 digit addendum.  The EAN-13 bar code with the 5 digit 
addendum is then transmitted as a single, concatenated bar code.  If a 5 
digit addendum is not found within the Addenda Timeout period, the EAN-
13 bar code is discarded.
Don’t Require 5 Digit Addenda:  If you have selected Require 5 Digit 
Addenda, and you want to disable this feature, scan Don’t Require 5 Digit 
Addenda.  EAN-13 bar codes are transmitted,...