Honeywell 1250g2 Manual

6 - 21
Check Digit Validation
When Check Character is set to Validate and Transmit, the scanner will 
only read Code 11 bar codes printed with the specified type check charac-
ter(s), and will transmit the character(s) at the end of the scanned data.
Code 11 Redundancy
If you are encountering errors when reading Code 11 bar codes, you may 
want to adjust the redundancy count.  Redundancy adjusts the number of 
times a bar code is decoded before transmission, which may reduce the 
number of errors.  Note...

6 - 22
Code 11 Message Length
Scan the bar codes below to change the message length.  Refer to 
Message Length Description (page 6-2) for additional information.  Mini-
mum and Maximum lengths = 1-80.   Minimum Default = 3, Maximum 
Default = 80.
Minimum Message Length
Maximum Message Length 

6 - 23
Code 128

Code 128 On/Off
128 Group Separator Output
If you wish to transmit the group separator characters “GS” (0x1D hex) with 
your Code 128 bar code output, scan the On bar code.  When Off is 
scanned, the group separator is not output.  Default =Off.
Code 128 Redundancy
If you are encountering errors when reading Code 128 bar codes, you may 
want to adjust the redundancy count.  Redundancy adjusts the number of 
times a bar code is decoded before transmission, which may reduce the 
number of...

6 - 24
128 Redundancy bar code below, then scan a redundancy count between 
0 and 10 on the Programming Chart inside the back cover of this manual.  
Then scan the Save bar code.  Default = 0.
Code 128 Message Length
Scan the bar codes below to change the message length.  Refer to 
Message Length Description (page 6-2) for additional information.  Mini-
mum and Maximum lengths = 1-80.   Minimum Default = 1, Maximum 
Default = 80.
ISBT 128
ISBT is a variation of Code 128 that supports concatenation of...

6 - 25
Concatenation Timeout
When searching for bar codes during concatenation, you may wish to set a 
delay used to find the next bar code.  Set the length (in milliseconds) for this 
delay by scanning the bar code below, then setting the timeout (from 1-
65535 milliseconds) by scanning digits from the Programming Chart, then 
scanning Save.  Default = 750.
ISBT 128 Predefined Concatenation Sequences
Note: You must enable Code 128 and ISBT 128 to use this feature.
The following bar codes are used to...

6 - 26
ISBT 128 Predefined Concatenation Sequences On/
Off
The following selections allow you to enable or require the Predefined ISBT 
128 Concatenation Sequences.  
If you scan Off, the predefined concatenation sequences are disabled.
If you scan the Allow Predefined Sequence code, then the scanner will 
output only the data combination specified in the predefined concatenation 
sequence you selected.  
If you scan the Require Predefined Sequence code, the data combination 
specified in the predefined...

6 - 27
Step 1.Scan the 1st Left Identifier bar code, below.
Step 2.Use the Programming Chart to scan 3, D (hex for “=”).
Step 3.Scan Save.
Step 4.Scan the 2nd Left Identifier bar code, below.
Step 5.Use the Programming Chart to scan 4, 7 (hex for “G”).
Step 6.Scan Save.
Step 7.Scan the 1st Right Identifier bar code, below.
Step 8.Use the Programming Chart to scan 3, D (hex for “=”).
Step 9.Scan Save.
Step 10.Scan the 2nd Right Identifier bar code, below.
Step 11.Use the Programming Chart to scan 3, C...

6 - 28
If you scan the Require User-Defined Sequence code, the data combina-
tion specified in the User-Defined concatenation sequence is required to 
transmit the data.  No data is output unless the sequence is read. 
Default = Off.
Content Verification
When the On bar code is scanned, the check character values are output 
along with the bar code data, thus allowing you to verify that the check 
character is in agreement with that calculated for the data stream.  Default 
= Off.
Transmit Identifiers...

6 - 29
tion Identification Number identifiers, only the first ID character is removed 
from the Donation Identification Number.  The second character is transmit-
ted as normal data.  Default = On.
Flag Digit Conversion
Type 3 flag digits are a part of the Donation Identification Number in an 
ISBT 128 bar code.  If you select On, the flag data is converted into a single 
MOD (37, 2) character and transmitted with the bar code data.  Scan Off if 
you do not want the flag digits transmitted.  Default =...

6 - 30
GS1-128

GS1-128 On/Off
GS1-128 Application Identifier Parsing
This allows a single GS1-128 bar code to be broken into multiple transmis-
sions based on the presence of application identifiers (AI) embedded in the 
bar code.  Scan Transmit Without Identifiers if you want the bar code 
broken into packets and stripped of the AI.  If you want the AI included, 
scan Transmit With Identifiers.  Default = Off.
GS1-128 Redundancy
If you are encountering errors when reading GS1-128 bar codes, you may...