Honda Pilot Owners Manual
Have a look at the manual Honda Pilot Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 328 Honda manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
uuIf a Tire Goes Flat uChanging a Flat Tire 610 Handling the Unexpected 1. Push the rear edge of the handle on the floor lid and open the lid. 2. Pull and remove the cover. Take the wheel nut wrench and jack-handle bar out of the rear side compartment. 3. Loosen the strap, th en take the jack out. ■Getting Ready to Replace the Flat Tire1Changing a Flat Tire NOTICE Do not use the jack if it doesn’t work properly. Call your dealer or a prof essional towing service. Handle CoverWheel Nut Wrench Jack Handle Bar Strap Jack 16 PILOT-31TG76000.book 610 ページ ２０１６年１０月１９日 水曜日 午後５時４分
611 uuIf a Tire Goes Flat uChanging a Flat Tire Continued Handling the Unexpected 4. Remove the cover and the rubber plug on the cargo area lining to access the shaft for the spare tire hoist. 5. Put the wheel nut wrench with the jack handle bar on the hoist shaft. Turn the wrench to the left to lower the spare tire to the ground. 6. Keep turning the wh eel nut wrench to create slack in the cable. 7. Remove the bracket from the spare tire.Cover Rubber Plug Jack Handle Bar Wheel Nut Wrench Bracket 16 PILOT-31TG76000.book 611 ページ ２０１６年１０月１９日 水曜日 午後５時４分
612 uuIf a Tire Goes Flat uChanging a Flat Tire Handling the Unexpected 8. Place a wheel block or rock in front and rear of the wheel diagonal to the flat tire. 9. Place the compact spare tire wheel side up under the vehicle body, near the tire that needs to be replaced. 10. Loosen each wheel nut about one turn using the wheel nut wrench. Wheel Blocks The tire to be replaced. 16 PILOT-31TG76000.book 612 ページ ２０１６年１０月１９日 水曜日 午後５時４分
Continued613 uuIf a Tire Goes Flat uChanging a Flat Tire Handling the Unexpected 1. Place the jack under the jacking point closest to the tire to be changed. 2. Turn the end bracket cl ockwise as shown in the image until the top of the jack contacts the jacking point. u Make sure that the jacking point tab is resting in the jack notch. 3. Raise the vehicle, using the jack handle bar and the jack handle, until the tire is off the ground. ■How to Set Up the Jack1How to Set Up the Jack Do not use the jack with people or luggage in the vehicle. Use the jack provided in your vehicle. Other jacks may not support the weight (“load”) or may not fit the jacking point. The following instructions must be followed to use the jack safely: •Do not use while the engine is running. •Use only where the ground is firm and level. •Use only at the jacking points.•Do not get in the vehicl e while using the jack. •Do not put anything on top of or underneath the jack. 3WARNING The vehicle can easily roll off the jack, seriously injuring anyone underneath. Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack. Jack Handle Bar Wheel Nut Wrench as Jack Handle 16 PILOT-31TG76000.book 613 ページ ２０１６年１０月１９日 水曜日 午後５時４分
uuIf a Tire Goes Flat uChanging a Flat Tire 614 Handling the Unexpected 1. Remove the wheel nuts and flat tire. 2. Wipe the mounting surfaces of the wheel with a clean cloth. 3. Mount the compact spare tire. 4. Screw the wheel nuts until they touch the lips around the mounting holes, then stop rotating. 5. Lower the vehicle and remove the jack. Tighten the wheel nuts in the order indicated in the image. Go around, tightening the nuts, two to three times in this order. Wheel nut torque: 94 lbf∙ft (127 N∙m, 13 kgf∙m) ■Replacing the Flat Tire1Replacing the Flat Tire Do not over tighten the wheel nuts by applying extra torque using your foot or a pipe. 16 PILOT-31TG76000.book 614 ページ ２０１６年１０月１９日 水曜日 午後５時４分
Continued615 uuIf a Tire Goes Flat uChanging a Flat Tire Handling the Unexpected 1. Remove the center cap and place the flat tire face up under the hoist. 2. Insert the hoist bracke t into the center hole of the flat tire. 3. Turn the wheel nut wrench with the jack handle bar clockwise until the flat tire rests against the underbody of the vehicle and you hear the hoist click. 4. Securely put the jack and wheel nut wrench back in the tool case. Store the case in the cargo area. ■Storing the Flat Tire1Storing the Flat Tire 3WARNING Loose items can fly around the interior in a crash and can seriously injure the occupants. Store the jack and tools securely before driving. Center Cap Wheel Nut Wrench Jack Handle Bar 16 PILOT-31TG76000.book 615 ページ ２０１６年１０月１９日 水曜日 午後５時４分
uuIf a Tire Goes Flat uChanging a Flat Tire 616 Handling the Unexpected If you replace a flat tire with the spare tire, the low tire pressure/TPMS indicator comes on while you are driving. After driving for a few miles (kilometers), the indicator will start blinking for a short time and then stay on. Tire Pressure Monitor Problem appears on the multi-informat ion display (MID), but this is normal. If you replace the tire with a specified regular tire, the warning message on the MID and the low tire pressure/TPMS indicator will go off after a few miles (kilometers). ■TPMS with Tire Fill Assist and the Spare Tire1 TPMS with Tire Fill Assist and the Spare Tire The system cannot monitor th e pressure of the spare tire. Manually check the spare tire pressure to be sure that it is correct. Use the TPMS specific whee ls. Each is equipped with a tire pressure sensor mount ed inside the tire behind the valve stem. 16 PILOT-31TG76000.book 616 ページ ２０１６年１０月１９日 水曜日 午後５時４分
617 Handling the Unexpected Engine Does Not Start Checking the Engine If the engine does not start, check the starter. Starter conditionChecklist Starter doesn’t turn or turns over slowly. The battery may be dead. Check each of the items on the right and respond accordingly.Check for a message on the MID. ●If the To Start, Hold Remote Near Start Button message appears 2If the Smart Entry Remote Battery is Weak P. 618 uMake sure the smart entry remote is in its operating range. 2 ENGINE START/STOP Button Operating Range P. 151 Check the brightness of the interior lights. Turn on the interior lights and check the brightness. ●If the interior lights are dim or do not come on at all 2 Battery P. 596●If the interior lights come on normally 2 Fuses P. 630 The starter turns over normally but the engine doesn’t start. There may be a problem with the fuse. Check each of the items on the right and respond accordingly. Review the engine start procedure. Follow its instructions, and try to start the engine again. 2 Starting the Engine P. 463 Check the immobilizer system indicator. When the immobilizer system indicator is blinking, the engine cannot be started. 2Immobilizer System P. 144 Check the fuel level. There should be enough fuel in the tank. 2 Fuel Gauge P. 113 Check the fuse. Check all fuses, or have the vehicle checked by a dealer. 2Inspecting and Changing Fuses P. 634 If the problem continues: 2Emergency Towing P. 635 1Checking the Engine If you must start the vehi cle immediately, use an assisting vehicle to jump start it. 2 Jump Starting P. 621 16 PILOT-31TG76000.book 617 ページ ２０１６年１０月１９日 水曜日 午後５時４分
618 uuEngine Does Not Start uIf the Smart Entry Remote Battery is Weak Handling the Unexpected If the Smart Entry Remote Battery is Weak If the beeper sounds, the To Start, Hold Remote Near Start Button message appears on the MID, the ENGINE START/STOP button flashes, and the engine won’t start, start the engine as follows. 1.Touch the center of the ENGINE START/ STOP button with the H logo on the smart entry remote while the ENGINE START/ STOP button is flashing. The buttons on the smart entry remote should be facing you. u The ENGINE START/STOP button flashes for about 30 seconds. 2. Depress the brake pedal and press the ENGINE START/STOP button within 10 seconds after the beeper sounds and the ENGINE START/STOP button changes from flashing to on. u If you don’t depress the pedal, the mode will change to ACCESSORY. 16 PILOT-31TG76000.book 618 ページ ２０１６年１０月１９日 水曜日 午後５時４分
619 uuEngine Does Not Start uEmergency Engine Stop Handling the Unexpected Emergency Engine Stop The ENGINE START/STOP button may be used to stop the engine due to an emergency situation even while driving. If you must stop the engine, do either of the following operations: • Press and hold the ENGINE START/STOP button for about two seconds. • Firmly press the ENGINE START/STOP button twice. The steering wheel will not lock. However, because turning off the engine disables the power assist the engine provides to the steering and braking systems, it will require significantly more physical effort an d time to steer and slow the vehicle. Use both feet on the brake pedal to slow down the vehicle and stop immediately in a safe place. The gear position auto matically changes to (P after the vehicle comes to a complete stop. Then, the power mode changes to VEHICLE OFF. The gear position auto matically changes to (P after the vehicle comes to a complete stop. Then press the ENGINE START/STOP button twice without depressing the brake pedal to change the mode VEHICLE OFF. The power mode is in ACCESSORY when the engine is stopped. To change the mode to VEHICLE OF F, change the gear position to (P after the vehicle comes to a complete stop. Then press the ENGINE START/STOP button twice without depressing the brake pedal. 1 Emergency Engine Stop Do not press the button while driving unless it is absolutely necessary for th e engine to be switched off. Automatic transmission models with electronic gear selector for U.S. models Automatic transmission models with elec tronic gear selector for Canadian models Automatic transmission models with shift lever Automatic transmission models with shift lever for Canadian models 16 PILOT-31TG76000.book 619 ページ ２０１６年１０月１９日 水曜日 午後５時４分