Honda Pilot Owners Manual

							570
uuMaintenance Under the Hood uAdding Engine Oil
Maintenance
Adding Engine Oil
1. Unscrew and remove the engine oil fill cap.
2. Add oil slowly.
3. Reinstall the engine oil fill cap, and tighten 
it securely.
4. Wait for three minutes and recheck the 
engine oil dipstick.1Adding Engine Oil
If any oil spills, wipe it up immediately. Spilled oil may 
damage the engine compartment components.
NOTICE
Do not fill the engine  oil above the upper mark. 
Overfilling the engine oil  can result in leaks and 
engine damage.
Engine Oil Fill Cap
16 PILOT-31TG76000.book  570 ページ  ２０１６年１０月１９日　水曜日　午後５時４分 
						

							571
uuMaintenance Under the Hood uChanging the Engine Oil and Oil Filter
Continued
Maintenance
Changing the Engine  Oil and Oil Filter
You must change the engine oil and oil fi lter regularly in order to maintain the 
engine’s lubrication. The engine may be  damaged if they are not changed regularly.
Change the oil and filter in accordance  with the maintenance message on the multi-
information display. 1.Run the engine until it reaches normal 
operating temperature, and then turn the 
engine off.
2. Open the hood and remove the engine oil 
fill cap.
3. Remove the drain bolt and washer from 
the bottom of the engine, and drain the 
oil into a suitable container.1Changing the Engine Oil and Oil Filter
NOTICE
You may damage the environment if you do not 
dispose of the oil in a suitable way. If you are 
changing the oil by yourself , appropriately dispose of 
the used oil. Put the oil in a sealed container and take 
it to a recycling center. Do not throw the oil away 
into a garbage can or onto the ground.
Drain Bolt
Washer
16 PILOT-31TG76000.book  571 ページ  ２０１６年１０月１９日　水曜日　午後５時４分 
						

							uuMaintenance Under the Hood uChanging the Engine Oil and Oil Filter
572
Maintenance
4. Remove the oil filter and dispose of the 
remaining oil.
5. Check that the filter ga sket is not stuck to 
the engine contact surface.
u If it is stuck, you must detach it.
6. Wipe away dirt and dust adhering to the 
contact surface of the oil filter base, and 
install a new oil filter.
u Apply a light coat of new engine oil to 
the oil filter rubber seal.
7. Put a new washer on the drain bolt, then 
reinstall the drain bolt.
u Tightening torque:
29 lbf∙ft (39 N∙m, 4.0 kgf∙m)
8. Pour the recommended engine oil into the 
engine.
u Engine oil change capacity (including 
filter):
5.7 US qt (5.4 ℓ)
9. Reinstall the engine oil fill cap securely and 
start the engine.
10. Run the engine for a few minutes, and   
then check that there is no leak from the   
drain bolt or oil filter.
11. Stop the engine, wait for three minutes,   
and then check the oil level on the   
dipstick.
u If necessary, add more engine oil.1Changing the Engine Oil and Oil Filter
You will need a special wrench to replace the oil 
filter. You can buy this wrench from a dealer.
When installing the new oil filter, follow the 
instructions supplied with the oil filter.
Reinstall the engine oil fill  cap. Start the engine. The 
low oil pressure indicator should go off within five 
seconds. If it does not, turn  off the engine, and check 
your work.
Oil Filter
16 PILOT-31TG76000.book  572 ページ  ２０１６年１０月１９日　水曜日　午後５時４分 
						

							573
uuMaintenance Under the Hood uEngine Coolant
Continued
Maintenance
Engine Coolant
This coolant is premixed with 50% an tifreeze and 50% water. Do not add any 
straight antifreeze or water.
We recommend you check the engine coolant  level every time you refuel. Check the 
reserve tank first. If it is completely  empty, also check the coolant level in the 
radiator. Add the engine coolant accordingly.
1.Check the amount of coolant in the reserve 
tank.
2. If the coolant level is below the  MIN mark, 
add the specified coolant until it reaches 
the  MAX  mark.
3. Inspect the cooling system for leaks.
Specified coolant: Ho nda Long Life Antifreeze/Coolant Type 2
■Reserve Tank
1Engine Coolant
NOTICE
If temperatures consistent ly below -22°F (-30°C) are 
expected, the coolant mixture should be changed to 
a higher concentration. Cons ult a dealer for more 
information.
If Honda antifreeze /coolant is not available, you may 
use another major brand non- silicate coolant as a 
temporary replacement. Check that it is a high quality 
coolant recommended for  aluminum engines. 
Continued use of any non-Honda coolant can result 
in corrosion, causing the cooling system to 
malfunction or fail. Have the cooling system flushed 
and refilled with Honda anti freeze/coolant as soon as 
possible.
Do not add rust inhibitors or other additives to your 
vehicle’s cooling system. They may not be compatible 
with the coolant or with the engine components.
MAX
MIN
16 PILOT-31TG76000.book  573 ページ  ２０１６年１０月１９日　水曜日　午後５時４分 
						

							uuMaintenance Under the Hood uEngine Coolant
574
Maintenance
1. Make sure the engine and radiator are 
cool.
2. Remove the engine compartment cover.
2 Engine Compartment Cover P. 567
3.Turn the radiator cap counterclockwise and 
relieve any pressure in  the coolant system. 
Do not push the cap down when turning.
4. Push down and turn the radiator cap 
counterclockwise to remove it.
5. The coolant level should be up to the base 
of the filler neck. Add coolant if it is low.
6. Put the radiator cap back on, and tighten it 
fully.
7. Pour coolant into the reserve tank until it 
reaches the  MAX mark. Put the cap back 
on the reserve tank.
■Radiator1 Radiator
NOTICE
Pour the fluid slowly and ca refully so you do not spill 
any. Clean up any spills immediately; they can 
damage components in the engine compartment.
3WARNING
Removing the radiator cap while the 
engine is hot can cause the coolant to spray 
out, seriously scalding you.
Always let the engine and radiator cool 
down before removing  the radiator cap.Radiator 
Cap
16 PILOT-31TG76000.book  574 ページ  ２０１６年１０月１９日　水曜日　午後５時４分 
						

							575
uuMaintenance Under the Hood uTransmission Fluid
Maintenance
Transmission Fluid
Have a dealer check the fluid level and replace if necessary.
■Automatic Transmission Fluid
Specified fluid: Honda ATF DW-1 (automatic transmission fluid)
Specified fluid: Honda  Automatic Transmission Fl uid ATF-TYPE 3.1 or 
higher
1 Automatic Transmission Fluid
NOTICE
Do not mix Honda ATF DW-1 (automatic 
transmission fluid) with  other transmission 
fluids.
Using a transmission flui d other than Honda ATF 
DW-1 (automatic transmissi on fluid)  may adversely 
affect the operation and dur ability of your vehicle's 
transmission, and da mage the transmission.
Any damage caused by usi ng a transmission fluid that 
is not equivalent to Honda ATF DW-1 (automatic 
transmission fluid) is not covered by Honda's new 
vehicle warranty.
Do not mix Honda ATF-TYPE 3.1 (or higher) with 
other transmission fluids.
Using a transmission flui d other than Honda ATF-
TYPE 3.1 (or higher) may adversely affect the 
operation and durability  of your vehicle’s 
transmission, and da mage the transmission.
Any damage caused by usi ng a transmission fluid that 
is not equivalent to Honda ATF-TYPE 3.1 (or higher) is 
not covered by Honda’s  new vehicle warranty.
Automatic transmission models with shift lever
Automatic transmission models with electronic gear 
selector
Automatic transmission models with shift lever
Automatic transmission models with electronic gear selector
16 PILOT-31TG76000.book  575 ページ  ２０１６年１０月１９日　水曜日　午後５時４分 
						

							576
uuMaintenance Under the Hood uBrake Fluid
Maintenance
Brake Fluid
The fluid level should be between the  MIN 
and  MAX  marks on the side of the reservoir.
Refilling Window  Washer Fluid
Check the amount of window washer  fluid by looking at the reservoir.
If the level is low, fi ll the washer reservoir.
If the washer fluid is low,  a message appears on the MID.
Pour the washer fluid carefully.  Do not overflow the reservoir.
Specified fluid: Honda Heavy Duty Brake Fluid DOT 3
■Checking the Brake Fluid
1Brake Fluid
NOTICE
Brake fluid marked DOT 5 is  not compatible with your 
vehicle’s braking system and can cause extensive 
damage.
If the specified brake fluid is not available, you should 
use only DOT 3 or DOT 4 fluid from a sealed 
container as a temporary replacement.
Using any non-Honda brake  fluid can cause corrosion 
and decrease the longevity of the system. Have the 
brake system flushed and re filled with Honda Heavy 
Duty Brake Fluid DOT 3 as soon as possible.
If the brake fluid level is at or below the  MIN mark, 
have a dealer inspect for l eaks or worn brake pads as 
soon as possible.
Brake Reservoir
MIN
MAX
1 Refilling Window Washer Fluid
NOTICE
Do not use engine antifreeze or a vinegar/water 
solution in the windshield washer reservoir.
Antifreeze can damage y our vehicle’s paint. A 
vinegar/water solution ca n damage the windshield 
washer pump.
Models without washer level sensor
Models with washer level sensor
16 PILOT-31TG76000.book  576 ページ  ２０１６年１０月１９日　水曜日　午後５時４分 
						

							577Continued
Maintenance
Replacing Light Bulbs
Headlight Bulbs
When replacing, use the following bulbs.1. Remove the clips.
2.  Remove the air intake duct.
High beam headlight: 60 W (HB3 for halogen bulb type)
Low beam headlight:
LED type
55 W (H11 for halogen bulb type)
■High Beam Headlight
1Headlight Bulbs
NOTICE
Halogen bulbs get very hot when lit.
Oil, perspiration,  or a scratch on the glass can cause 
the bulb to overhe at and shatter.
The headlight aim is set by  the factory, and does not 
need to be adjusted.
However, if you regularly carry heavy items in the 
cargo area, have the aiming readjusted at a dealer or 
by a qualified technician.
When replacing a halogen bu lb, handle it by its base, 
and protect the glass from c ontact with your skin or 
hard objects. If you touch  the glass, clean it with 
denatured alcohol and a clean cloth.
Models without automatic headlight adjusting system
Models with Auto high-beam system
Models without Auto high-beam system
ClipsDriver side
16 PILOT-31TG76000.book  577 ページ  ２０１６年１０月１９日　水曜日　午後５時４分 
						

							uuReplacing Light Bulbs uHeadlight Bulbs
578
Maintenance
3. Push the tab to remove the coupler.
4. Rotate the old bulb counterclockwise to 
remove.
5. Insert a new bulb into the headlight 
assembly and turn it clockwise.
6. Insert the coupler into the connector of the 
bulb.
1Headlight Bulbs
Remove clip using phillips head screwdriver.
Insert the clip with the  central pin raised, and push 
until it is flat.
Center pin
Push until the 
pin is flat.
TabCoupler
Bulb
Both sides
16 PILOT-31TG76000.book  578 ページ  ２０１６年１０月１９日　水曜日　午後５時４分 
						

							579
uuReplacing Light Bulbs uDaytime Running Lights and Parking Lights
Maintenance
1. Push the tab to remove the coupler.
2. Rotate the old bulb counterclockwise to 
remove.
3. Insert a new bulb into the headlight 
assembly and turn it clockwise.
4. Insert the coupler into  the connector of the 
bulb.
Daytime Running Lights  and Parking Lights
Daytime running lights and parking lights are LED type. Have an authorized Honda 
dealer inspect and replace the light assembly.
Daytime running light bulbs and high  beam headlight bulbs are the same.
2Headlight Bulbs  P. 577
Parking light bulbs and front turn signal bulbs are the same.
2Front Turn Signal/Parking* and Fog* Light Bulbs  P. 580
Front Side Marker Lights
Front side marker lights are LED type. Have an authorized Hond a dealer inspect and 
replace the light assembly.
■Low Beam Headlights1 Low Beam Headlights
Low beam headlights are LED type. Have an 
authorized Honda dealer in spect and replace the light 
assembly.
Models with Auto high-beam systemModels without Auto high-beam system
TabCoupler
Bulb
Models with fog light
Models without fog light
* Not available on all models
16 PILOT-31TG76000.book  579 ページ  ２０１６年１０月１９日　水曜日　午後５時４分