Honda Bmw 5 Service Manual

- 
... ---- - Fenders, -- Engine ~oodl 
4 Remove bolts (arrows) along top edge  of fender. 
- Carefully remove fender  from body. 
Detent screw  on left and right  hood  hinge 
(1) must be set at 
25 i- 1 mm (1 k .04 in). 
- Installation is reverse  of removal, noting the following: 
Before installing new  fender, clean old sealant  and protec- 
tive  coating  from mounting  surfaces. 
Position new  fender and loosely  install all mounting bolts. 
Align fender with door  pillar  and inner  fender,  then...

Hood, raising to service position 
CAUTION- 
Do not  switch  on the  windshield  wipers  with  the  engine 
hood  raised.  As a precaution,  remove  the wiper 
motor 
fuse.  See 610 Electrical  Component  Locations. 
The 
hoodis heavy Before removing  the hoodsupports, 
be  sure  to have  an assistant  help support  the hood. 
< Open hood fully.  With the help  of a partner,  support hood  and 
remove  retaining clips  (arrow) on upper  end of  pressurized 
lifting struts. Pull struts  off hood. 
<...

Fenders, Engine ~ood/ 
Hood, removing and installing 
With hood  open: 
Remove  hood wiring harness mounting clip 
(A) 
Disconnect electrical harness connector (B). 
Unplug windshield  washer hose (C). 
WARNING- 
The hood is  heavy Before removing the hoodsupports,  be 
sure  to have  an assistant help 
support the hood. 
Mark position of hinge plates. 
With the  help of a assistant, support hood and  remove retain- 
ing clips 
(A) on upper end  of pressurized lifting  struts. Pull 
struts  off hood....

41 0-8 
(Fenders, Engine Hood 
Hood, aligning 
When installing  the hood, align the hinges as  close to the orig- 
inal painted  surface as possible. Movement  of the  hood  on its 
attaching  hardware  may require touch-up paint. 
The  hood  should be aligned  so that  gap 
(arrows) to fender is 
as  even as possible. 
4 If height  adjustment  at rear  of hood  is off, adjust  height using 
adjusting screw  in lower hinge 
(arrow). Loosen  and reposi- 
tion as necessary. 
If height  adjustment  at 
ing...

Fenders, Engine ~oodl 
Adjusting detent buffers for hood: 
Raise  hood. 
* Shape pieces  of rubber (butyl) tape into  two IOmm col- 
umns and place on buffers 
(A). 
* Close hood. 
Measure dimension  of the  compressed rubber  tape. 
Using  measurement  dimension, adjust  detent buffer 
(A) 
Hood should be under a slight preload. (+0.5 mm). 
Fellow  the same  procedure on the front  buffers 
(B). 
- After adjustment have been  made, check that hood  lid is flush 
against  detent buffers  and 
if...

41 0-1 0 
I Fenders, Engine Hood 
Hood latch components 
1. Hood 
2.  Gas pressurized 
Strut 
3.  Spacer 
4.  Hinge 
5.  Ground stud 
6.  Torx 
bolt 
7.  Torx bolt 
8.  Hex bolt 
9. Bowden cable bracket 
10.  Ball  pin 
11.  Torx bolt 
12.  Spring pin 
13.  Stop  buffer 
14. 
Bowden cable 
15.  Lower  hood lock 
16. 
Bowden cable 
17.  Torx 
bolt 
18. Stop buffer 
19.  Hex nut 
20. Torx bolt 
21.  Hood latch   

Fenders, Ensine HOO~I 
Hood release cable and spring pins, 
adjusting 
Before  adjusting  hood pins,  be sure  the hood  is aligned even- 
ly to fenders  and front panel. 
- Malte sure bowden cable, which connects  both hood  loclts 
together, is  seated in lock guide  on both left and right  loclts. 
4 Loosen hood spring  pin bolts (A) and  retaining hoolt bolts (B) 
at hood on left  and right sides only enough  to allow move- 
ment. 
- Lower (but  do not fully  latch)  hood several times  so pins  on...

General ........................... .41 1.2  Door hinge adjustment ................ 41 1-5 
Door hinge assembly 
.................. 41  1-6 Doors ............................. 411-2 
Front or rear door. removing 
Door  Panels ....................... 41 1-7 
and installing ....................... .41 1.2  Door trim panel. removing  and installing ... 41 1-7 
Door  check.  replacing 
................. .41 1.4  Sill trim panels ...................... 41 1-1 0   

Doors 
This repair group  covers front and  rear  door repair  informa- 
tion.  It includes  removal  and  installation of front  and rear 
doors  and trim  panels. 
For  information  on 
airbag removal  and installation,  see 721 
airbag. 
For information on the power  door windows  and door glass 
replacement, see 
512 Door  Windows. 
For  information  on  the power  door 
loclting system,  see 515 
Central  Locking  and Anti-Theft. 
WARNING- 
E39 cars are fitted  with side-impact airbags in the front...