GTE Omni Si Database Technical Practices Manual

 r52108187M-335 TL-130200-1001
Table 8.1Recent Change Sequences (Continued)
FUNCTIONTRANSACTION
NUMBERCOMMENTSShow CIP card location
and assigned ports.221,146Show CIP card location
ShowVCIP or DVCIPcard location and
assigned ports.221
146Show VCIP or DVCIP card
location.
Show lines on a 
VCIP or
DVCIP card.
Add a CAS 
Main- or
ACD agent.111
115
43
142Add instrument data.
Add line feature data.
Add agent group
Change supervisor
status association.
Delete a CAS Main
or ACD agent.115 (or 111) 
_Delete...

THIS PAGE IS INTENTIONALLY LEFT BLANK. 

-TL-130200-100-t
OFF-LINE9.0 The off-line maintenance disk contains the software for
DIAGNOSTICSconducting off-line diagnostic testing. Diagnostic tests are only
performed on off-line equipment because the generic and data
base software are voided when the maintenance disk is is loaded
into the system.
The following tests are conducted using the Off-Line
Diagnostics Testing Program:
* Line Cards and Direct-Inward-Dialing (DID) Trunk Cards
0 System Memory
o Channel Memory
0 Network
o Disk Drive
l Page,...

-TL-130200-1001
Table 9.1Menu of Test Options
Menu No.Test Option
0SYSTEM MEMORY TEST
1CHANNEL MEMORY TEST
2PAGING CARD TEST
3NETWORK TEST
4DISK DEVICE TEST
5SERIAL DEVICE CONTROLLER TEST
ITONE CARD TEST1 ATT12 CARD TEST
I
8ILINES/TRUNKS TEST1 TOUCH CALLING RECEIVER TEST1
Loading the Program9.3 The following steps load the Off-Line Maintenance
Program:
1. Place the program disk into the disk drive.
2. Connect the maintenance terminal to the NSDC card 
(FB-20992-A), port 0.
3. Press the reset button on...

:._TL-130200-1001
7. Answer the prompt by typing 
“Y.” or “N. “ The Menu of Test
Options appears on the terminal display screen. Choose the
test and type the menu number.
8. The test selected runs with the results shown on the terminal
screen
NOTES:
1. Type “CONTROL-C 
“ to abort a test. The Menu of Test
Options appears on the terminal screen.
52102. Type “CONTROL-X” to restart a System Memory or Channel
Memory test. This entry also aborts other diagnostic tests.
3. Except for the System Memory test, any...

TL-130200-1001Automatic Testing9.5 After all manual tests are completed, the program changes
over to automatic testing with test results displayed as before.
Automatic testing repeats tests one and two under CPU control
with a one-second delay between write and read. Test three
writes all possible data patterns into each address location with
data in the adjacent address location incremented by one.
Example:
. .If address A000 contained a data pattern of “01 “, successive
address locations in test three...

TL-130200-1001Fast Test Option
Retest Option
System
Memory Test9.6 Fast test option reduces the amount of time spent running
memory tests. This is done by using a shorter data pattern which
reduces the number of patterns written to memory in tests three
and four.
9.7 Automatic testing restarts the retest option if no failures have
occurred. If a failure does occur, testing stops and the results of
all ranges are displayed in circular order.
9.8 This test checks the ability of system memory to
store...

TL-130200-1001
Table 9.2 S‘stem Memar Test Card and Address Range Correlation
IO-17
Dl-D7
Range No. AddressRangeDo (2,3)
Range No.Card SlotFunction
I0200 to IFFF
0860 to 08BF1
 OAOO to OABF
/OCOOPad Memory
(both files)
1000 to 13FF
coY5Common Memory
Get Started File
ClY4Common Memory
Expansion Fife 1400 to 17FF
(  2050 to 
3FFF2Yl
Yl2
3
IYlI
4
5
6
7
COO0 to DFFF
EOOO to FFFF8
NOTES:
1. Range 1 does not exist for Il. I1 contains the Off-Line
Diagnostic Program at range 1 during the test.
2. Ranges A, B,...

:
TL-130200-1001
_’System Memory9.8.1
Testing ProceduresUse the following steps to conduct the System Memory
Test:
1. Select option “0“ from the Menu of Test Options. The system
responds:
Fujitsu GTE 
OMNI SI SYSTEM MEMORY TEST
TO DEFAULT ALL VALUES TYPE 0 OTHERWISE TYPE 1
2. If all values are to stay at their default values type 
“0” If not,
type “1.” If a “0” value was typed, the test begins. If a “1” was
typed, the system responds:
ALL PAGES TYPE 0; OTHERWISE TYPE 
43. If all data and instruction...

TL-130200-1001
8. If automatic delay (under system control) is used, type “0”.For manual time delay, type “1 
“. The system will respond:
TO DEFAULT INTER TEST TIME DELAY TYPE 0,
OTHERWISE TYPE 1
9. If default values are used, type 
“0” and tests begin. If other
time values are used, type 
” 1.” The system responds:
FOR EACH TEST’S DELAY TIME, TYPE TWO DIGITS:
XX 
- FOR # OF SECONDS DELAY IN TEST 1 & 2
10.Enter values from “00“ to “FF” for the time delay on tests 1
‘*and 2 (“00” means no time delay, “FF”...