GTE Omni Si Database Technical Practices Manual

5210l-L-1 30200-l 001
INST PAGE 0 RANGE 01 TEST #3MEMORY FAILURE LOCATION IS: 5FE0
DATA: WRITTEN FO READ 
Fl3. A pass count occurs after all ranges selected for testing are
*completed and a retest requested. The count appears in
decimal, runs from 
“00” to “99”, and repeats beginning at
” 00.”
4. Testing stops on the range for that pass only when a failure
occurs. At the start of each pass, all ranges selected for
testing are retested if the retest option was selected.
5. If a failure occurs on ranges CO...

2. Enter a “0” if the Get Started File is tested and/or a “1” if the
Expansion File is tested, followed by a (CR). If both files’
channel memories are tested, type “01”. If all files are
selected, then a (CR) is not needed. The system responds:
FOR RETEST TYPE 0; OTHERWISE TYPE 1
3. Now refer to step five of the System Memory Test procedures
and continue (paragraph 96.1)..: Test Results9.9.2 All of the test results described may not appear since they
depend on how the Channel Memory Test was set up.
1...

TL-130200-1001Test Results9.192 After completion of the Paging Card Test, the system
responds with the following :
1. With successful completion of the test the system responds:
PAGING CARD PASSES TEST
2. Memory read-after-write error on instruction page 0,
memory address 1100. The system responds:
MEMORY WRITE FAILURE ON PAGING TEST
PAGE 00
MEMORY FAILURE LOCATION IS: 1100
3. Paging failure in which page write went to Instruction Page 1
instead of instruction page 0 writing to range 
#l. The system...

TL-130200-1001
2. If the channel memory was not initialized, the system responds:
NETWORK FAILURE: CAN’T WRITE TO CHANNEL
MEMORY
TESTING STOPPED DUE TO THE ABOVE ERRORS
3. If control memories A or B were not initialized, the system
responds:
NETWORK FAILURE: CAN’T WRITE TO CONTROL TESTING STOPPED DUE TO THE ABOVE ERRORS
4.. If pad memory was not initialized, the system responds:
NETWORK FAILURE: CAN’T WRITE TO PAD MEMORY
TESTING STOPPED DUE TO ABOVE ERRORS
5. If channel, control, or pad memory was not...

TL-130200-1001Fault Correction9.11.3 The following steps correct faults detected by the Network
Test:
1. If the problem was found to be initializing or writing to channel,
control, or pad memory, replace the Channel Memory 8085
card (FB-17218-A). Reinstall the original card if the problem
continues after replacement.
2. Repeat the Network Test.
3. If the failure continues, check all cabinet cables for short
circuits. If an open is found, replace the faulty cable and rerun
the Network Test.
NOTE: Steps 4,...

TL-130200-1001
3. Verification of the FMS/disk communications link generates the
following menu:
I-------------------------------------------------,II/  DISK DEVICE TEST SELECTION MENUI
I
I)  0) REPEAT FMS TEST
I
II  1) TEST DEVICE 
#O (10 MBYTE FIXED)I
I
I2) TEST DEVICE #2 (800 KBYTE)II  X) RETURN TO MAIN OFF LINE DIAGNOSTICS MENU 
i)  ENTER SELECTION 
- > >II
I
!IIL---___------__-----------------------------------,
- Selection of option “0” repeats the FMS test (on-line)
- Selection of option “1”...

TL-130200-100152103. Examples of FMS Test error messages include:
. FMS COMMUNICATIONS ERROR
PERFORMING 
FMS COMMUNICATION TEST
ERROR DETECTED WHILE PERFORMING FMS
COMMUNICATION TEST
FMS TEST ENDED
l FMS RAM ERROR
PERFORMING FMS RAM TEST
ERROR DETECTED WHILE PERFORMING FMS RAM TEST
FMS TEST ENDED
o FMS CONFIGURATION ERROR
POLLING FMS FOR DISK CONFIGURATION
ERROR DETECTED WHILE POLLING FMS FOR DISK
CONFIGURATION
FMS TEST ENDED
l DISK TEST MENU WHEN FMS TEST FAILS
DISK DEVICE TEST SELECTION MENU
0) REPEAT...

The above steps generate the following messages as the system
completes each operation:~-------------------------------------------------------------~!  FIXED DISK DEVICE TEST IN PROGRESS....I1  PERFORMING DISK CONTROLLER DIAGNOSTICS
I
II
- STILL PERFORMING DISK CONTROLLER DIAGNOSTICS:I  DELETE TEST FILE
j  
DETERMINING DISK FREE SPACE
ICREATING TEST FILE
/  WRITING TO TEST FILE
I
STILLWRiTiNG TO TEST FILE
I
ISTILLWRITING TO TEST FILE
II
I
STiLLWRiTiNG TO TEST FILE
I
ISTILLWRITING TO TEST FILE
I
I...

TL-130200-1001r-------------------------------------------------~
; FIXED DEVICE TEST SUCCESSFULLY COMPLETED fIIL-------------------------------------------------~The system displays the “DISK DEVICE TEST SELECTION
MENU” on completion of this test.
Test Device #29.12.4 Test Device #l (option 2) instructs the system to perform
a read/write verification for the FMS and a floppy disk in the disk
drive. The following prompts appear:
INSERT A SPARE FLOPPY DISK IN DISK DRIVE
NOTE: ANY DATA ON DISK WILL BE...

. .TL-130200-1001
STILL FORMATTING FLOPPY DISK
MOUNTING FLOPPY DISK
DETERMINING DISK FREE SPACE
CREATING TEST FILE
WRITING TO TEST FILE
STILL WRITING TO TEST FILE
STILL WRITING TO TEST FILE
CLOSING TEST FILE
OPENING TEST FILE
READING TEST FILE
STILL READING TEST FILE
STILL READING TEST FILE
CLOSING TEST FILE
DELETING TEST FILE
FLOPPY DISK DEVICE TEST
SUCCESSFULLY COMPLETED
The system displays the “DISK DEVICE TEST SELECTION
MENU” on completion of this test.
Return to Main Menu9.12.5 Return to Main Menu...