GTE Omni Si Database Technical Practices Manual

5210Active 
DCPs 0600
1 l/21/86 13:32:34(Uptime 1 
21:01:14)
8187 

TL-130200-10012. ENTER PASSWORDSYSTEM LEVEL: 
@
ADMIN OPTIONS
Select the 
ADMIN option you choose to work
with
1. Data Base Editor2. Maintenance and Administration
3. Run ADMP A-side test code4. Reload the ADMP
NOTES:ENTER the number of your choice: 1
Press RETURN
Enter 1 to 51. The system will allow three chances for correct password and
then return to NETPKG.
2. User Guide is written for level 5 passwords.
81875210 

TL-130200-1001Fault Resolution7.10.2 This paragraph focuses on the use of maintenance tools
to resolve faults, and, in addition, on the interpretation and
application of feedback from the ADPM maintenance terminal .
PCB RemovalNOTE: The following cards cannot be removed and replaced
and Replacementwithout placing them 00s.
MNEMONICFB NUMBERDESCFWI-ION.
VPLCFB-17226-AVoice Packet Line Card (8 circuits)
PBE/T
PRFB-17227-A
FB-17228-APacket Bus Extender/Terminator Card (See
Note)
Packet Router (See Note)...

TL-I 30200-l 001
Fault Code 39Description:
ADMP InitializationThis fault indicates errors in the ADMP-PEC interface. The
Related ErrorsPEC, which has the ADMP in it, has some problems (e. g., PEC
OOS, PEC has lost communication with the ADMP). This fault
may also indicate inconsistency in data switch related data base.
Register Data As System Prints:, CECX ,
OnlineCEC A!gi 7
006 = Noresponseon
contlguratlon data
01 = Undetlned Status
08 = No associated voice
call 
processing (VW)
09 = Device type
not...

TL-130200-1001Fault Code 41
Disk 
I/O ErrorsFAULT CODE 
- 41
NO
q YESC=FF
POWER DOWN
SYSTEM
PSUPY FOR
NO
+ YES
R&R FLOPPY
DISK DRIVE-q-e-)5210M-279 

TL-130200-1001
THIS PAGE IS INTENTIONALLY LEFT BLANK.
M-28081875210 

TL-130200-1001RECENT CHANGE8.0 The Recent Change feature is part of the primary system
software. Plain language entries are used to display, or change
data base information. The SHOW, 
LlST, or DISPLAY functions
display data base information, while ADD, CHANGE, or DELETE
functions are used to change data base information.
-..Recent Change allows the user to modify the data base in order
to satisfy voice communications and data processing
requirements. Recent Change is also used to keep up with
hardware...

TL-130200-1001
Detailed descriptions and applications of System Recent
Change transactions are covered in the OMNI SI Recent
Change Manual S.V.R. 
5.2.1.0. The Recent Change Manual
includes the following information:
List of Recent Change Transactions
Recent Change Menu Options
Manual Recent Change
Recent Change Transaction Sequences
On-Line Maintenance appears in part three of this section,
while CAS 
Main/ACD Supervisor Options coverage follows
here in paragraph 4.2
The Recent Change transaction, Save...

5210TL-130200-1001
With this prompt the user ends the exercise (type E period),
repeats the same transaction (type 
R period), or proceeds to
another transaction (type another transaction number from zero
to 224 period).
If the user enters E, the Recent Change Options Menu appears:
r-------------------------------------------------~
IRECENT CHANGE OPTIONSI
II
I
IA) BEGIN
I
I
II
I
6) SAME ONEI
IIC) BACK ONEI
I
IID) HELP
IIIIE) ERROR EXPLANATION
I
I
IF) SYSTEM OPTIONS MENU
I
IX) END RECENT CHANGE
I
II
I...

TL-130200-1001CAS Main/ACD Help8.2.1 HELP (Option D) and ERROR EXPLANATION (Option E)
assist the user in selecting additional transactions.
When working in CAS 
Main/ACD, or FADS, Help Menus for most
transactions are accessed by entering CONTROL H (press the
CNTRL and H keys at the same time). The System will respond :
r----------------------------------------------------------------------------------~IIIHOW TO USE THE HELP MENUS
II.=.I
II
I.._ MOST OF THE SUPERVISORY RECENT CHANGE AND FAD...