GTE Omni Si Database Technical Practices Manual

Figure 7.3Visual Fault Indicator - UCB (DCP) (INSIOOS LED and RESET BUTTON)
Red Indicator Lamp
Reset button
Reset Button: Initializes DCP by accessing hard disk files via ADPM for loading DCP memory
Red indicator
5210
ON STEADY
This ADMP is in
service.
FLASHING (60 IPM)
This ADMP is out of
service while
attempting to load
(requests
loading). Passed ROM
memory self-test.
FLASHING (120 IPM)
Failed ROM
memory self-tests
DCP cannot
communicate with
PR.
8/87M-265 

278-922-300Figure 7.4Visual Lamp Indicators and Switches - Asynchronous Packet Manager (APM)
KTEST BUTTON
TESTLAMP
LAMPON STEADYFLASHING (60 IPM)FLASHING (120IPM)
Link
LAMPCallThis APM is inThis APM is out ofFailed ROM
service (loaded).service whilememory 
self-attempting to loadtests.
(Requests down loading). APM DTE/DCE
Passed ROM memoryswitch is in the
self-test.wrong position.
ON STEADYOFFTerminal busyTerminal idle (no
(connected toconnection).
another terminal).
M-266
81875210 

278-922-300Figure 7.4Visual Lamp Indicators and Switches - Asynchronous Packet Manager (APM)
(Continued1
VIEW SHOWING LAMPSCALL
LINK
5210
LAMPON STEADYFLASHING (60 IPM)FLASHING (120 IPM)Red indicatorThis APM is inThis APM is out of
Failed ROM
lit
service (loaded).service while
memory self-tests.
attempting to loadAPM DTEIDCE
(Requests down loading).switch is in the
Passed ROM memory
wrong position.
self-test.
LAMPON STEADYOFFCall
Terminal busyTerminal idle (no
(connected toconnection).
another terminal...

278-922-300Figure 7.4Visual Lamp Indicators and Switches - Asynchronous Packet Manaaer (APMI(Continued 
-- .
VIEW SHOWING BUTTONS
TEST
_
FRONT
--
REAR
LINEDATA
r-lRESETOUT IN
/DCE DTE
BUTTON FUNCTIONS
BUTTONTest
ResetFUNCTIONCauses test message to appear on ADMP terminal
screen 
- ERMA CH(2).
Interrupts any data call and resets APM; requests
reload from ADMP.
DTE/DCESelects DTE or DCE mode of operation.
$1875210 

278-922-300Figure 7.5Visual Lamp indicators and Switches - Synchronous Packet Manager (SPM)
FRONT
. .
X.25SWITCHX.25
TE
ST
REARI
LAMPION STEADYOFFX.25 Test
ActiveDuring a link X.25 test
(X.25 test button
pressed)During an idle state
(no link connection)
I
LAMPION STEADY
lx.25During a link X.25 hostDuring an idle state (no
link connection)
LAMPON STEADYFLASHING (60 IPM)FLASHING
(120 PM)Switch LinkThis SPM is inThis SPM is out of serviceFailed ROM
servicewhile attemptingmemory 
self-(loaded).to load...

278-922-300THIS PAGE IS INTENTIONALLY LEFT BLANK.
81875210 

TL-130200-1001Maintenance TerminalTable 7.4 is a listing of the maintenance terminal fault codes and
Fault Code Listingstheir functions.
CODE
I--00
_- 01,...
-- I-
02
5210I03
I04I05
j 06
I
07I
08I
I09
10
11
F
12I
I13
Table a.4Fault Code Listings
FUNCTIONSCEC BLOCK PARITY
CEC DYNAMIC RAM MEMORY FAILURE
CEC-PEC CONTROL MEMORY READ-AFTER-WRITE
FAILURE
CEC-PEC COMMON MEMORY READ-AFTER-WRITE
FAILURE
CEC-TO-CEC TOTAL COMMUNICATION LINK FAILURE
CEC-CEC SINGLE COMMUNICATION LINK FAILURE
CEC SYSTEM NETWORK TEST...

Table 7.4Fault Code Listings (Continued)I
CODEIFUNCTIONSI
221 MDR OUTPUT CONTROL FAULT
I
23IFUTURE
24FUTURE_.
25REAL- TIME CLOCK FAILURE
I
26IPOWER FAILURE
I.27 .1 HOTEUHEALTH CARE DISK BACK-UP FAlLUREI
281 CAS MAIN/ACD AGENT INSTRUMENT DATA LINK ERROR 1
29CAS MAIN/ACD MESSAGE QUEUE ERROR
30ATTENDANT CONSOLE DATA CHECK ERROR
I
311 PEC ODDB BACK-UP FAILURE
I
321 CIPNCIP CARD FAILURE
I
331 CIPNCIP PORT FAILURE
34REMOTE FADS REPORTING ERROR
35REMOTE FADS REPORTING ERROR
I
361 SYSTEM RESET
37FUTURE
38CEC-PEC...

TL-130200-10015210
ADMP Terminal andl Terminal Prerequisites
User Prerequisites
-Must be a DEC VT-l 00, VT-l 01, or equivalent type video
terminal
- Baud rate set to 1200
- Secondary keypad requires key function overlay as shown in
VT-l 01 Secondary Keypad Overlay
NOTE: Must have full cursor flow control.
VT-1 01 Secondary Keypad OverlayGETPUT
MEMMEMSEARCH
MEM
GET
PRODPUT
PROD
GET
OTHERPUT
OTHER
FIELDRECORD
DEFAULTDEFAULTSEARCH
PRODEXIT
HELPREFRESH
SCREEN
I
0 User Prerequisites
- Level 0 password...

o Enter Key: The (ENTER) key is the large key at the bottom
right corner of the numerical keypad to the right of the
keyboard.
ADMP Terminal Cursoro During the first screen display, the cursor is positioned at the
Positioningfirst changeable field.
o To move forward to the next field, depress (tab), (return), or
(right arrow) keys.
l To move backward to the previous field, depress (left arrow)
key
NOTES:1. Forward means a field to the right or below the current
cursor position.
2. Backward means a field...