GTE Omni Si Database Technical Practices Manual

- .-TL-130200-1001
The system prints the following on the maintenance terminal:
r---------------------_____-----__-_--_-__---------------_---em-----1
j SYNTAX ERROR#N =an error was found in the input message
I
j COMMFND FAILED= the request was not processed successfully
I
i DEVICl%n aa.bb.cc
I
I
1
whereI
II
I#n= the following types:
1
I09 =
ADMPI
I. OA = DCP
I
IOE = SPM
I
IOF = APM
I
I12 =
DFPAPMI
I13 = NIC
I
I
I
I
and whereI
Iaa.bb.cc. =the version of the software loaded in the device
I
I
I
I
I
I
I
I
I...

-
TL-1~30200-1001
2. For the DVCIP card, circuit numbers are defined:
Voice
0
2
4
6
Line Cards with
Featurephopnes7.8.2 To force a CIP, VCIP, or DVCIP interface card in service or
out of service, enter the following:
. .
r’-------------‘-----------------------------------------------------I1I‘FORCE CIP CARD 
 IS> /
OS> ;
whereI
I
I
 = 0I = 0 to 15I
I
I
‘-----“-----------------------------------------------------------------~
Trunks7.8.3 To force a trunk circuit from active to maintenance busy
using the...

,! . .
5210
TL-130206-1001To force a Digital Featurephone connected to VPLC2 (type 
VP20)voice port out of service, enter the command given below
r------------------------------------------------------------------~III
i  FORCE DN 
< directory-no. >I
I
I
I
I
IS.I
I
OS.I
I
I
II
IIorIIIII
lFORCE DIFP    IS.I
II
IIOS.I
II
I
II  where .I
II
IIII  = three- or four-digit directory number of aII
I  Featurephone
III 
 = 0I
I
I = AtoDII
I  = 
oto11IIi  
= oto7I
I...

TL-130200-1001Load CommandsM-258To force a trunk circuit from active to maintenance busy using
the SID, enter the following:
r-------------------------------------------------------~I
1
II  FORCE TRUNK SID 
  OS>I
II
Ij  whereI
I
II
IIII  
 = 0II
I  
Csid >= Trunk circuit SID relative to the PEC; 0 to 63IIL-------------------------------------------------------~7.9 LOAD commands are used only in data applications
The purpose of the load commands are to permit reloading of
devices which may be...

5210TL-130200-1001
If LOAD DEVICE SPECIFIC is typed, the device indicated is reset
and reloaded. Any call up on the device is lost.r-------------------‘------------------------------------------------~;  LOAD DEVICE- TYPE PEC GROUP SLOT CIRCUIT OPI
I;  or
I
II  LOAD DEVICE- TYPE ALL
I
II  or
I
I)  LOAD DATA
I
II
IIII  whereII1I/DEVICE TYPE =ADMP, DCP, SPM, APM, OR DATA (Option ADMP
I
II
I_ reloads ADMP only. Option Data reinitializes the entire network.) 
IIIIPEC = 
PECnumberI
IGROUP = file group
SLOT =...

TL-130200-1001
IM-2608h37
Table 7.2 shows the responses for the various load data
commands seen at the maintenance terminal.
Table 7.2Responses for Load Data Commands at Terminal
INPUTRESPONSE
Type in LOAD DATA when the
A message prints:
data switch cannot be loaded.COMMAND FAILED,
.~.followed by an explanation given by
the ADMP.
Type in LOAD DATA when the
data switch can be loaded.The data switch will be loaded and
a message will print: IN PROGRESS
When the load is complete, a message
indicating the...

TL-l30200-1001
Load Conlmand9.9.1 Table 7.3 shows the responses for the various load
Responsescommands at the maintenance terminal.
Table 7.3Responses for Load Commands at Terminal
,f the device input is VPLC2, and the
device is VPLC2 with both voice and
data circuits equipped,
If the PEC is not able to do a download
3n the voice device,
If-everything is all right in the PEC, and
ihe voice circuits start downloading,
If the ADMP is not able to do an
operational load on the data 
device,If everything is...

TL-130200-1001
THIS PAGE IS INTENTIONALLY LEFT BLANK.
5210 

278-922-300PD-200 Maintenance7.10 This section contains information related to maintenance
Tools and Fault Isolationtools and fault isolation.
Maintenance Tools7.10.1 This paragraph covers information on visual fault/lamp
indicators and peripheral devices, maintenance commands, and
on-line diagnostics. Maintenance personnel will be able to do
the following:
. .l Identify and interpret data terminal tests and parameters
l Identify and interpret ADMP terminal commands and menus
l Classify fault code...

278-922-300Figure 7.2 Visual Fault Indicator -ADMP-A (INSlOOS LED and RESET BUTTON)
7e+
-
-1*4i-
El--
00
00l e00
eooel o
l e
- Red indicator lamp
_ Reset button
_ ADMP terminal cable connection
50-pin male ribbon connector
3m/part no. 3433
LAMP
Red indicatorON STEADYThis ADMP is in
service.FLASHING (60 IPM)This ADMP is out of
service while
attempting to load
(requestsloading). Passed ROM
memory self-test.FLASHING (120 IPM)
Failed ROM
memory self-tests.
81875210