GGP Italy SPA Brush Cutter TR 25J Instruction Manual

REFILLING THE FUEL TANK
Pressure may increase in
recipients containing petrol due to ambient
temperature.
Open the cap carefully to avoid it flying off.
Store the fuel in a cool place; never leave it in
the sun.
–Place the brush cutter in a stable position with
the tank aperture facing upwards (fig. 3).
–Clean the tank cap and the surrounding area
to prevent foreign bodies entering the tank.
–Fill the tank, using a suitable container that
prevents accidental fuel spillage.
–Highly flammable and in...

could cause the cord to become caught up or
wear or damage to the starter assembly.
–Never hold the brush cutter still by placing
your foot or knee on the drive tube; this could
deform the transmission shaft making it unus-
able.
When the engine is start-
ed, the cutting tool starts to rotate immedi-
ately. Take the brush cutter to minimum
speed by pressing and releasing the throttle
lever. Check that the cutting tool stops turn-
ing when the engine is running at minimum
speed.
If the engine does not...

–IF YOU ARE NOT FAMILIAR with use of the
brush cutter, practise the procedures with
the engine switched off and the switch in
the OFF “STOP” position.
–ALWAYS FREE THE WORK AREA of objects
such as cans, bottles, stones, etc.. Hitting
these objects can cause serious injury to
the operator or others present and damage
the brush cutter. If you accidentally knock
against an object, SWITCH OFF THE
ENGINE IMMEDIATELY and inspect the
cutter. Never work with a damaged or
faulty brush cutter.
–ALWAYS CUT OR MOW...

• Cutting around trees (fig. 13)
Cut by gradually approaching tree trunks to pre-
vent the line from knocking against the tree.
Walk around the tree from left to right. Move the
end of the line towards the grass to cut, keeping
the line head tilted slightly forwards.
The nylon line may CUT OR
DAMAGE SMALL BUSHES. The impact of the
nylon line against the trunk of bushes or trees
with soft bark MAY CAUSE SERIOUS DAMAGE
TO THE PLANT.
• Mowing (fig. 14)
In more severe mowing conditions tilt the head
with...

REPLACING THE EDGE-TRIMMING HEAD
LINE
To replace the nylon line, follow the instructions
enclosed with the head (supplementary page
separate from the guide).
Never replace the nylon
line with a line made of any other material
(e.g. metal wire). 
DISASSEMBLY (fig. 16)
To block the cutting unit and prevent shaft rota-
tion, fit the steel rod (A) (provided) into the hole
(B) on the upper left side of the head unit, slow-
ly turn the tool until the rod penetrates the hole
of the metal ring nut. Turn the head...

EXTRAORDINARY MAINTENANCE
Contact your local Authorised Service Centre for
any procedures not considered to be ordinary
maintenance.
Repairs carried out by unauthorised service cen-
tres and unqualified personnel will invalidate the
warranty.
ONLY USE AND REQUEST ORIGINAL SPARE
PARTS. 
STORAGE
If you do not follow these
instruction oily deposits may form in the carbu-
rettor, making starting difficult or causing perma-
nent damage due to disuse of the brush cutter.
1. Clean the outer part of the engine,...

ENTROUBLESHOOTING35
TROUBLESHOOTING
Incorrect start-up procedure
Incorrect carburation
Spark plug dirty
Fuel filter clogged
Dirty air filter
Incorrect carburetion
Incorrect carburetion
Incorrect spark plug gap
Incorrect carburetion
Mixture with incorrect petrol-oil ratio
The machine will not
start up or keeps
stopping
PROBLEMPROBABLE CAUSE CORRECTIVE MEASURE
Follow the instructions in the User
Manual.
Have the carburettor adjusted at an
Authorised Service Centre.
Clean, correct the gap or replace spark...

EN36TECHNICAL DATA
*Earthed in accordance with ISO 11806 (without fuel, cutting and protection equipment)
•  1left (or front) 
•   2right (or rear)                     
TECHNICAL DATA
2-stroke air-cooled
25.4 cm
3
0.8 kW
10300 1/min 2900 1/min
10300 rpm min
-1
Ø  25,4 mm
Centrifugal LD L8RTFElectronic WYJ 398
Petrol  – oil 50:1
600 cm
3
112 dB
99.5 dB
10.24 m/s
2
7.05 m/s2
6.23 m/s2
3.35 m/s2
4.3 kg Ok///
///
///
Motor type
Displacement
Power
Maximum revolution speed
Idle speed
Tool Maximum revolution...

FRPRESENTATION37
Cher Client,
Nous désirons avant tout vous remercier de la préférence que vous avez accordée à nos produits et
nous espérons que l’utilisation de cette machine vous réservera de grandes satisfactions et répondra
pleinement à votre attente. Ce manuel a été rédigé pour vous permettre de bien connaître votre machi-
ne et de l’utiliser dans les meilleures conditions de sécurité et d’efficacité; n’oubliez pas qu’il est par-
tie intégrante de la machine, gardez-le à portée de la main pour...

38IDENTIFICATION DE LA MACHINE ET DE SES PIÈCESFR
IDENTIFICATION DE LA MACHINE ET DE SES PIÈCES
1) Moteur
2) Bougie
3) Poignée de démarra-
ge
4) Levier du starter
5) Dispositif d’injection
(Primer)
6) Filtre air
7) Bouchon réservoir
mélange
8) Poignée arrière
9) Levier accélérateur
10) Levier de sécurité
11) Interrupteur
Marche/Arrêt
11a) Levier d’arrêt de
l’accélérateur
12) Entretoise de sécuri-
té
13) Poignée avant
14) Tube de transmission
15) Protection avant
16) Tête de coupe avec
fil nylon...