GGP Italy SPA Brush Cutter TR 25J Instruction Manual

ITLOCALIZZAZIONE GUASTI19
LOCALIZZAZIONE GUASTI
Procedura di avvio non corretta
Carburazione non corretta
Candela imbrattata
Filtro carburante otturato
Filtro aria sporco
Carburazione non corretta
Carburazione non corretta
Candela con gap
(distanza tra elettrodi) errato
Carburazione non corretta
Miscela con errato rapporto benzina - olio
Macchina non si
avvia oppure non si
mantiene in moto 
PROBLEMAPROBABILE CAUSA AZIONE CORRETTIVA
Seguire istruzioni del Manuale utente.
Far regolare il carburatore presso...

IT20DATI TECNICI
DATI TECNICI
* Massa secondo norma ISO 11806 (senza carburante, dispositivi di tagli\
o e protezione) 
•  1sinistra (o anteriore) 
•  2destra (o posteriore)                              2 tempi raffreddato ad aria
25.4 cm
3
0.8 kW
10300 1/min 2900 1/min
10300 rpm min
-1
Ø 25,4 mm CentrifugaLD L8RTF
Elettronica WYJ 398
Benzina – olio 50:1 600 cm
3
112 dB
99.5 dB
10.24 m/s
2
7.05 m/s2
6.23 m/s2
3.35 m/s2
4.3 kg Ok///
///
///
Tipo di motore
Cilindrata
Potenza
Velocità massima di rotazione...

ENPRESENTATION21
Dear Customer,
Firstly, we wish to thank you for having chosen our products and hope that the use of this machine will
be extremely satisfying for you and fully meet your expectations.
This manual has been drawn up to allow your to get to know your machine well and use it in safe and
efficient conditions; please do not forget that it is an integral part of the machine and keep it to hand
to be consulted at all times and consign it with the machine if you should sell or lend it to...

22IDENTIFICATION OF THE MACHINE AND PARTSEN
IDENTIFICATION OF THE MACHINE AND PARTS
1) Motor
2) Spark plug
3) Starter handle
4) Starter lever
5) Primer
6) Air filter
7) Fuel tank cap
8) Rear handgrip
9) Throttle lever
10) Safety lever
11) Start/Stop switch
11a) Accelerator stop
lever
12) Safety spacer
13) Front handgrip
14) Drive shaft 
15) Front guard 
16) Cutting head with
nylon line
17) Ratings plate
The brush cutter you
have purchased is sup-
plied with the following
accessories:
1) user and mainte-...

1)Warning! Danger
2)Read the instruction booklet before using this
machine.
3)Your hearing is at risk of irreparable damage.
Anyone operating this machine under normal
conditions during continuous daily use may be
exposed to a noise level equal to or exceeding
85 dB (A). 
The operator must wear Personal Protective
Equipment (PPE). Whenever the machine is in
use, safety goggles must be worn to safeguard
against flying objects, as must ear protectors,
such as a soundproof helmet, in order to protect
the...

Each element of this machine is a potential safe-
ty hazard if used improperly or poorly main-
tained.
We recommend that special attention is paid to
the sections starting with the following headings:
or 
These give details or further
information on what has already been said, and
are aimed at preventing damage to the machine
or causing damage.
Non-observance will
result in the risk of injury to oneself or others.
Non-observance will
result in the risk of serious injury or death to
oneself or others.
A)...

4.Replace the exhaust silencers if they are
faulty.
5.Each time the brush cutter is used, a general
check must be carried out on the condition of
the equipment, cutting unit, guards and fasten-
ing elements before switching it on, to ensure
that the parts are not worn, damaged or loose.
Always check that the throttle lever and “STOP”
button work correctly. 
Check that the lever that blocks the throttle
(safety lever) works correctly; the throttle should
only work when the safety lever on the upper
side...

speed. Spare parts that are not the same quality
may damage the machine and jeopardise safety.
3.Wear thick gloves to remove and refit the cut-
ting tools.
4.Never store the trimmer with fuel in the tank
in an environment where petrol fumes could
come into contact with a flame, spark or sources
of extreme heat.
5.Store the trimmer in a clean and dry environ-
ment, out of the reach of children.
6.Let the motor cool down before it is stored in
any environment.
7.To reduce the risk of fire, clean any...

In order to ensure correct
and safe use of the edge trimmer, the assem-
bly instructions for protection and safety
components must be followed meticulously.
The manufacturer shall not be held liable if
the edge trimmer is used without the afore-
mentioned protection and safety devices.
FRONT HANDGRIP (fig. 1)
Edge trimmers are normally supplied with the
front handgrip disassembled inside the packag-
ing. 
Therefore, it must be attached following the pro-
cedure indicated below. 
The front handgrip must...

In order to use the edge trimmer, clothes must
be worn that protect against objects thrown up
by the tool (e.g. stones). Wear safety shoes with
a slip-proof sole, gloves, safety goggles (the
visor used on its own does not protect the eyes
sufficiently), tight-fitting clothes. Do not wear
loose-fitting clothes, scarves, ties, jewellery or
other dangling objects that could get caught on
branches. Long hair must be tied up and pro-
tected. Equipment to protect hearing such as ear
defenders must be worn....