GE Logiq P5 User Manual

Introduction
LOGIQ 5 Basic User Manual 7-11
Direction 2300002-100 Rev. 2
Specifying measurement and display options (continued)
Displaying the
Results and
Summary
WindowsTypically, the Results Window and Summary Window are shown 
on the monitor display. If you want, you can remove them from 
the display. To remove them, select the Options tab, and then 
select Display Off. To re-display them, select Display Off.
NOTE:  Display Off removes both the Results Window and Summary 
Window from the monitor...

General Measurements and Calculations
7-12 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
General Instructions (continued)
The following are actions you can take while performing 
measurements.
Calculation formulas are available in the Advanced Reference 
Manual.
HINTS•  Before making measurements, to stop the acquisition of 
image data, press Freeze.
•  For measurements such as distance, to make fine 
adjustments before completing the measurements, press 
Measure to toggle between active...

Introduction
LOGIQ 5 Basic User Manual 7-13
Direction 2300002-100 Rev. 2
Erasing measurements
The following actions erase measurements from the systems 
memory: 
HINTS•  If you adjust the Trackball, unfreeze the image, or press 
Clear, the system erases all completed measurements and 
calculations on the display. Measurements and 
calculations, however, remain on the worksheets.
•  If you select New Patient, the system erases all 
measurements and calculations on the display and clears 
the worksheets.
•...

General Measurements and Calculations
7-14 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Measurement and Calculation Setup
When you receive your LOGIQ 5 system, the studies and 
measurements are organized for typical work flows. If you want, 
you can change this set up. You can specify which studies are in 
each exam category, and which measurements and calculations 
are in each study. You can change the measurements that are 
available on the Touch Panel. The LOGIQ 5 allows you to 
quickly and...

Measurement and Calculation Setup
LOGIQ 5 Basic User Manual 7-15
Direction 2300002-100 Rev. 2
Starting Study and Measurement SetUp 
You make changes to studies and measurements in the 
Measurement & Analysis screen. To open the screen:
1.  On the Touch Panel, select Utility.
2.  On the Touch Panel, select Measure.
3.  On the monitor display, select the M & A tab.
The system displays the Measurement & Analysis screen 
on the monitor display.
 Figure 7-4. Measurement & Analysis screen
1. Selection menu:...

General Measurements and Calculations
7-16 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Selecting an exam category
When you open the Measurement & Analysis screen, it displays 
the exam category that was last used on the system. To select 
the exam category you want to work with:
1. Move the Trackball to highlight the exam category at the 
top of the Selection menu. 
2. Press Set.
The system displays a list of exam categories.
3. Move the Trackball to highlight the exam category you 
want.
4....

Measurement and Calculation Setup
LOGIQ 5 Basic User Manual 7-17
Direction 2300002-100 Rev. 2
Selecting the measurement mode
In the Measurement menu section of the Measurement & 
Analysis screen, select one of the following:
• 2D (B-Mode)
• MM (M-Mode)
•  Dop (Doppler Mode)
The Selection menu lists studies and measurements for the 
selected mode.
 Figure 7-6. Select Mode 

General Measurements and Calculations
7-18 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Selecting a study or measurement
To work with a folder or measurement, you must first select it in 
the Selection menu. The Selection menu lists the studies and 
measurements for an exam category. The studies and 
measurements are organized in a hierarchy, in the same order 
that they are organized on the Touch Panel. The illustration 
below shows the highest level of the Obstetrics exam category, 
with the...

Measurement and Calculation Setup
LOGIQ 5 Basic User Manual 7-19
Direction 2300002-100 Rev. 2
Selecting a study or measurement (continued)
After you select a study, the Selection menu shows all folders 
and measurements in the study. The Folder section of the 
Measurement & Analysis screen changes, and lists the 
measurements. The Selection menu shows all measurements 
for the OB-1 exam category. 
 Figure 7-8. Selection Menu: OB-1 Exam Category 

General Measurements and Calculations
7-20 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Selecting a study or measurement (continued)
The illustration below shows the Selection menu after the BPD 
measurement is selected. The Measurement section is now 
displayed, with information about the BPD measurement. 
 Figure 7-9. Selection Menu: BPD Measurement