Epson Stylus Pro 4400 User Manual

Maintenance and Transportation291
7
7
7
7
7
7
7
7
7
7
7
7
English
4. Carefully pull the empty cartridge straight out of the printer.
w
Warning:
If ink gets on your hands, wash them thoroughly with soap 
and water. If ink gets into your eyes, flush them immediately 
with water.
c
Caution:
Do not shake cartridges (that have been installed previously) 
with too much force. 
5. Make sure the replacement ink cartridge is the correct color, 
and remove it from the package. Shake the ink cartridge well 
before...

292Maintenance and TransportationNote:
A protection system is provided to prevent improper cartridge 
insertion. If you cannot insert the ink cartridge smoothly, the type 
of cartridge may be incorrect. Check the package and product code.
6. Hold the ink cartridge with the arrow mark facing up and 
pointing to the rear of the printer, and then insert it into the 
slot. Do not force the cartridge in further by hand.
Note:
If the Ink check light remains on, this indicates the ink cartridge may 
not be...

Maintenance and Transportation293
7
7
7
7
7
7
7
7
7
7
7
7
English
Note:
If you install an ink cartridge in the wrong slot, NO INK CRTG 
appears on the LCD. Make sure that the correct ink cartridge is 
installed in the correct slot.
8. Close the ink compartment cover. The printer returns to the 
previous status.
Note:
If you have installed 220 ml ink cartridge, do not close the ink 
compartment cover.
 

294Maintenance and Transportation
Converting the Black Ink Cartridges
You can change the black ink according to your purpose. You can 
choose either Matte Black or Photo Black. 
c
Caution:
To avoid interrupting a black ink change, observe the following 
conditions:
❏Do not turn off the printer.
❏Do not open the top cover.
❏Do not remove the rear cover.
❏Do not move the paper lever to the released position.
❏Do not remove the ink cartridges.
❏Do not remove the maintenance tank.
❏Do not unplug the power...

Maintenance and Transportation295
7
7
7
7
7
7
7
7
7
7
7
7
English
1. Make sure that READY appears on the LCD panel.
2. Press the Menu 
 button to enter the SelecType mode.
3. Press the Paper Feed  or Paper Feed  button to display 
MAINTENANCE on the LCD, and then press the Menu 
 button.
4. Press the Paper Feed  or Paper Feed  button to display 
BK INK CHANGE, and then press the Menu  button.
5. Press the Menu 
 button again to execute.
6. Make sure RAISE THE RIGHT INK LEVER appears on the LCD, 
and then...

296Maintenance and Transportation 7. Make sure RAISE THE LEFT INK LEVER appears on the LCD, 
and then raise the ink lever on the left ink compartment.
8. Make sure REMOVE INK CRTG appears on the LCD, and then 
remove all four ink cartridges from the left ink compartment.
9. Make sure INSTALL CNVRSION CRTG appears on the LCD, and 
then insert three conversion cartridges in the slots on the left 
ink compartment.
 

Maintenance and Transportation297
7
7
7
7
7
7
7
7
7
7
7
7
English
Note:
If REPLACE CNVRSION CRTG appears on the LCD, press the Pause 
 button. Remove the old conversion cartridge(s) from the left ink 
compartment, and then insert the new conversion cartridge(s). 
Finally, go to step 4 to start again.
10. Make sure LOWER THE LEFT INK LEVER appears on the LCD, 
and then lower the ink lever on the left ink compartment.
11. The printer starts draining ink, and DRAINING XX% appears on 
the LCD. Wait until...

298Maintenance and Transportation 12. When draining is complete, RAISE THE LEFT INK LEVER 
appears on the LCD. Raise the ink lever on the left ink 
compartment.
13. Make sure REMOVE CNVRSION CRTG appears on the LCD, and 
then remove the conversion cartridges from the slots on the 
left ink compartment.
 

Maintenance and Transportation299
7
7
7
7
7
7
7
7
7
7
7
7
English
14. Make sure INSERT INK CRTG appears on the LCD, and then 
insert the cartridges in their specified slots.
15. Make sure LOWER BOTH INK LEVERS appears on the LCD, and 
then lower the ink levers on the right and left ink 
compartments.
 

300Maintenance and Transportation 16. Make sure RAISE THE BOTH INK LEVERS appears on the LCD, 
and then raise the ink lever on the right and left ink 
compartments.
17. The printer starts charging ink. After a while, ink lever 
messages appear on the LCD. When a message appears on the 
LCD, raise or lower the ink levers accordingly until READY 
appears on the LCD. 
Note:
Because ink charging after black ink conversion consumes a large 
quantity of ink, you may need to replace the ink cartridges soon.
18....