Epson EPL N3000DT User Manual

298Troubleshooting
HDD Check
The printer is checking the Hard Disk Drive.
Image Cart ID Error
The wrong imaging cartridge has been installed. Replace it with 
the correct imaging cartridge for this printer. See “Replacing the 
imaging cartridge” on page 224 for instructions.
Image Optimum
There is insufficient memory to print the page at the specified 
print quality. The printer automatically lowers the print quality 
so that it can continue printing. If the quality of the printout is not 
acceptable,...

Troubleshooting299
9
9
9
9
9
9
9
9
9
9
9
9
Invalid AUX I/F Card
This message means that the printer cannot communicate with 
the installed optional interface card. Turn off the printer, remove 
the card, then reinstall it.
Invalid HDD
Either the optional Hard Disk Drive is damaged or it cannot be 
used with this printer. Turn off the printer and remove the Hard 
Disk Drive.
Invalid N/W Module
There is no network program, or the network program cannot be 
used with the EPL-N3000. Update the program....

300Troubleshooting
Manual Feed xxx
The manual feed mode is specified for the current print job. Make 
sure the paper size indicated by xxx is loaded, then press the N 
Start/Stop button.
For details on the manual feed mode, see “Manually feeding 
paper” on page 19.
Mem Overflow
The printer has insufficient memory to execute the current task. 
Press the N Start/Stop button on the control panel to resume 
printing. Or press the   Cancel Job button to cancel the print job.
Menus Locked
This message appears...

Troubleshooting301
9
9
9
9
9
9
9
9
9
9
9
9
To clear this error message, select Clear Warning from the control 
panel’s Reset menu. See “How to access the control panel menus” 
on page 339 for instructions.
To prevent this problem from happening again, add more 
memory to your printer as described in “Memory Module” on 
page 204 or reduce the resolution of the image to be printed.
NonGenuine Toner
The installed imaging cartridge is not a genuine EPSON product. 
Installing a genuine toner cartridge is...

302Troubleshooting
Outbin Select Error
The specified paper size or paper type cannot be output to the 
face-up tray. Change the paper size or paper type, or select the 
face-down tray as the output tray.
Paper Out XXX YYY
There is no paper in the specified paper source (XXX). Load paper 
of the indicated size (YYY) into the paper source.
Paper Set XXX YYY
The paper loaded in the specified paper source (XXX) does not 
match the required paper size (YYY). Replace the loaded paper 
with the correct size...

Troubleshooting303
9
9
9
9
9
9
9
9
9
9
9
9
PS3 Hard Disk full
The memory allocated for writing PostScript 3 commands on the 
optional Hard Disk Drive is full.
To clear this error, select Clear Warning from the control panel’s 
Reset menu. For instruction about accessing the control panel 
menus, see “How to access the control panel menus” on page 339.
RAM Check
The printer is checking the RAM.
Ready
The printer is ready to receive data and print. The level of 
remaining toner is also indicated on the...

304Troubleshooting
Reset
The printer’s current interface has been reset and the buffer has 
been cleared. However, other interfaces are still active and retain 
their settings and data.
Reset All
All printer settings have been reset to the default configuration, 
or to the last settings that were saved.
Reset to Save
A control panel menu setting was changed while the printer was 
printing. Press the N Start/Stop button to clear this message. The 
setting will become effective after printing has...

Troubleshooting305
9
9
9
9
9
9
9
9
9
9
9
9
Stacker Full
The output paper at the Stacker is full. Remove the paper that was 
output and press the N Start/Stop button. Printing resumes.
Status Sheet
The printer is printing the status sheet.
Sleep
The printer is currently in the power-save mode. This mode is 
canceled when the printer receives print data or the Reset button 
is pressed.
Toner Low
The imaging cartridge has less than 10% of toner remaining and 
need to be replaced.
See “Replacing the imaging...

306Troubleshooting
Unable Clear Error
The printer cannot clear an error message because the error status 
still remains. Try solving the problem again.
Warming Up
The printer is warming up the machine to be ready to print.
Worn Fuser
This message indicates that the fuser unit has reached the end of 
its service life. Prepare a new fuser unit.
See “Replacing the fuser unit” on page 228 for instructions.
Write Error ROM P
The printer is unable to write data into the ROM module correctly. 
You cannot remove...

Troubleshooting307
9
9
9
9
9
9
9
9
9
9
9
9
Using the Cancel Job button
The   Cancel Job button on your printer is the quickest and 
easiest way to cancel printing. Pressing this button cancels the 
currently printing job. Pressing the   Cancel Job button for more 
than two seconds deletes all jobs from the printer memory, 
including jobs the printer is currently receiving or printing.
Using the Reset menu
Selecting Reset from the control panel’s Reset menu stops 
printing, clears the print job being...