Epson Aculaser M4000N User Manual

AcuLaser M4000 Series Users Guide
Using the Control Panel61
Setup Menu
*1Available only when the corresponding option is installed.
*2Available only when you use A4, A5, B5, LT, HLT, LGL, EXE, GLG, GLT, or F4 size paper.
*3Available only for ESC/Page, ESC/P2, FX, or I239X mode.
*4Not available in PS 3 mode.
*5After this setting is changed, the printer will automatically reboot and the new setting takes effect.
*6After this item is changed, the setting value takes effect after a warm boot or after the...

AcuLaser M4000 Series Users Guide
Using the Control Panel62
Time to Sleep
Specifies the length of time until the printer enters the sleep mode if there are no button operations.
Time Out
Specifies the length of the time, in seconds, before a time out when interfaces are being switched 
automatically. The time before a time out occurs is the length of time from the point when no data 
is being received from an interface until the point of switching the interface. If the printer has a 
print job when...

AcuLaser M4000 Series Users Guide
Using the Control Panel63
Duplex
Turns duplex printing on or off. This allows you to print on both sides of a page. 
Binding
Specifies the binding direction of the printout.
Start Page
Specifies whether printing starts from the front or back of the page.
Offset Stacking
Specifies whether or not to separate print jobs by shifting the output to the left and then to the right.
Paper Type
Specifies the type of paper to be used for printing. The printer adjusts the printing...

AcuLaser M4000 Series Users Guide
Using the Control Panel64
Page Protect
Allocates additional printer memory for printing data, as opposed to receiving it. You may need to 
turn this setting on if you are printing a very complex page. If a Print Overrun error message 
appears on the LCD panel during printing, turn this setting on and reprint your data. This reduces 
the amount of memory reserved for processing data so your computer may take longer to send the 
print job, but it will allow you to print...

AcuLaser M4000 Series Users Guide
Using the Control Panel65
Reset Menu
Clear Warning
Clears warning messages that show errors except for these that occur from consumable products 
or mandatory-replacement parts.
Clear All Warnings
Clears all warning messages that appear on the LCD panel.
Reset
Stops printing and clears the current job received from the active interface. You may want to reset 
the printer when there is a problem with the print job itself and the printer cannot print 
successfully.
Reset...

AcuLaser M4000 Series Users Guide
Using the Control Panel66
Confidential Job Menu
This menu allows you to print or delete print jobs stored in the printer’s memory using the 
Confidential Job feature of the printer driver’s Reserve Job function. You need to enter the correct 
password to access this data. For instructions on using this menu, see “Using the Confidential Job 
Menu” on page 92.
Parallel Menu
These settings control communication between the printer and the computer when using the 
parallel...

AcuLaser M4000 Series Users Guide
Using the Control Panel67
Note:
❏To activate Buffer Size settings, you must turn off the printer for more than five seconds then turn it back 
on. Or, you can perform a Reset All operation, as explained in “Reset Menu” on page 65. 
❏Resetting the printer erases all print jobs. Make sure the Ready light is not flashing when you reset the 
printer.
USB Menu
*1After this item is changed, the setting value takes effect after a warm boot or after the power is turned on again....

AcuLaser M4000 Series Users Guide
Using the Control Panel68
USB I/F
Allows you to activate or deactivate the USB interface.
USB Speed
Allows you to select the operation mode of USB interface. Selecting HS is recommended. Select FS 
if HS does not work on your computer system. 
Buffer Size
Determines the amount of memory to be used for receiving data and printing data. If Maximum is 
selected, more memory is allocated for receiving data. If Minimum is selected, more memory is 
allocated for printing...

AcuLaser M4000 Series Users Guide
Using the Control Panel69
PCL Menu
These settings are available in the PCL mode.
*1Available only when downloaded fonts are available.
*2Depending on the font that has been selected.
FontSource
Sets the default font source.
Font Number
Sets the default font number for the default font source. The available number depends on the 
settings you made.
Pitch
Specifies the default font pitch if the font is scalable and of fixed-pitch. You can select from 0.44 to 
99.99 cpi...

AcuLaser M4000 Series Users Guide
Using the Control Panel70
Height
Specifies the default font height if the font is scalable and proportional. You can select from 4.00 to 
999.75 points, in 0.25-point increments. This item may not appear depending on the Font Source 
or Font Number settings.
SymSet
Selects the default symbol set. If the font you selected in Font Source and Font Number is not 
available in the new SymSet setting, the Font Source and the Font Number settings are 
automatically replaced...