Epson AcuLaser C2900DN User Manual

4min
Fault Time-out
Purpose:
To specify the amount of time the printer waits before canceling a job that stops abnormally. The print
job is cancelled if the time-out time is exceeded.
Values:
OffDisables the fault time-out.
On*60sec*Sets the amount of time the printer waits before canceling a job that stops
abnormally.
3–300 sec.
Job Time-out
Purpose:
To specify the amount of time the printer waits for data to arrive from the computer. The print job is
cancelled if the time-out time is exceeded.
Values:...

Date Format yy/mm/ddSets the date format.
mm/dd/yy
dd/mm/yy*
Time Format 12HSets the time in 12-hour format.
24H*Sets the time in 24-hour format.
*1The default for Date Format varies depending on country-specific factory default.
Audio Tones
Purpose:
To configure settings for tones emitted by the printer during operation or when a warning message
appears.
Values:
Control Panel Off*Does not emit a tone when the operator panel input is correct.
OnEmits a tone when the operator panel input is correct....

AutoClear Alert Off*Does not emit a tone 5 seconds before the printer performs auto clear.
OnEmits a tone 5 seconds before the printer performs auto clear.
All Tones OffDisables all the alert tones.
On*Sets the volume of all the alert tones at once.
mm / inch
Purpose:
To specify the default measurement unit displayed after the numeric value on the operator panel.
Values:
Millimeters (mm)*Selects millimeter as the default measurement unit.
Inches (")Selects inch as the default measurement unit.
Note:...

Values:
Off*Does not automatically print a job history report.
OnAutomatically prints a job history report.
The Job History report can also be printed using the Report/List menu.
Print ID
Purpose:
To specify a location where the user ID is printed.
Values:
Off*Does not print the user ID.
Top LeftPrints the user ID on the top left of the page.
Top RightPrints the user ID on the top right of the page.
Bottom LeftPrints the user ID on the bottom left of the page.
Bottom RightPrints the user ID on the bottom...

Banner Sheet
Note:
Banner Sheet feature is available only when the optional 250-sheet paper cassette unit is installed on the
printer.
Purpose:
To specify the position of banner sheet, and also specify the tray in which the banner sheet is loaded.
Values:
Insert Position Off*Does not print the banner sheet.
Start SheetInserted before the first page of every job.
End SheetInserted after the last page of every job.
Start&End
SheetInserted before the first page of every job and after the last page of every...

Substitute Tray
Purpose:
Specifies whether to use paper of a different size when the paper that is loaded in the specified tray does
not match the paper size settings for the current job.
Values:
Off*No tray size substitute accepted.
Larger SizeSubstitutes paper of next largest size. When there is no larger paper size, the
printer substitutes paper of nearest size.
Closest SizeSubstitutes paper of nearest size.
Auditron Mode
Purpose:
To specify whether to limit the functions that can be used per user by...

Values:
Disable*Does not print on both sides of letterhead.
EnablePrints on both sides of letterhead.
Low Toner Msg
Purpose:
To specify whether to show the alert message when the toner is low.
Values:
OffDoes not show the alert message when the toner is low.
On*Shows the alert message when the toner is low.
Maintenance Mode
Use the Maintenance Mode menu to initialize the NV (non-volatile) memory, configure the plain
paper quality adjustment settings, and configure the security settings.
Note:
Values...

Adjust BTR
Purpose:
To specify the transfer roller voltage adjustment for each paper type.
The default settings may not give the best output on all paper types. If you see mottles on the print
output, try to increase the voltage. If you see white spots on the print output, try to decrease the
voltage.
Note:
The print quality changes depending on the setting values you select for this item.
Values:
Plain 0*
-6 to +6
Light Card 0*
-6 to +6
Heavy Card 0*
-6 to +6
Envelope 0*
-6 to +6
Labels 0*
-6 to +6
LW...

The default settings may not give the best output on all paper types. When the printed paper has
curled, try to lower the temperature. When the toner does not fuse on the paper properly, try to
increase the temperature.
Note:
The print quality changes depending on the setting values you select for this item.
Values:
Plain 0*
-6 to +6
Light Card 0*
-6 to +6
Heavy Card 0*
-6 to +6
Envelope 0*
-6 to +6
Labels 0*
-6 to +6
LW Gloss Card 0*
-6 to +6
HW Gloss Card 0*
-6 to +6
Auto Adjust Regi
Purpose:
To...

Adjust ColorRegi
Purpose:
To manually perform color registration adjustment.
Manual Color Registration Adjustments are required when the printer is initially installed and after
the printer is moved.
Note:
The Adjust ColorRegi feature can be configured when Auto Adjust Regi is set to Off.
Values:
Auto AdjustAutomatically performs color registration correction.
ColorRegi ChartPrints a color registration chart. The color registration chart prints a
lattice pattern of yellow, magenta, and cyan lines. On the...