Epson AcuLaser C2900DN User Manual

Font Pitch
Purpose:
To specify the font pitch for scalable mono spaced fonts, within the range of 6.00 to 24.00. The default
is 10.00.
Font pitch refers to the number of fixed-space characters in a horizontal inch of type. For
nonscheduled mono spaced fonts, the pitch is displayed, but cannot be changed.
Note:
The Font Pitch menu is only displayed for fixed or mono spaced fonts.
Form Line
Purpose:
To set the number of lines in a page.
Values:
64*1 (mm series)/60*1 (inch series)Sets the value in...

Values:
On*Enables the Image Enhance feature.
OffDisables the Image Enhance feature.
Hex Dump
Purpose:
To help isolate the source of a print job problem. With Hex Dump selected, all data sent to the printer is
printed in hexadecimal and character representation. Control codes are not executed.
Values:
Disable*Disables the Hex Dump feature.
EnableEnables the Hex Dump feature.
Draft Mode
Purpose:
To save toner by printing in the draft mode. The print quality is reduced when you print in the draft
mode....

Add-CRThe CR command is added.
CR=CR, LF=CR-LF, FF=CR-FF
CR-XXThe CR and LF commands are added.
CR=CR-LF, LF=CR-LF, FF=CR-FF
Output Color
Purpose:
To specify the color mode to Color or Black and White. This setting is used for a print job that does
not specify a print mode.
Values:
Black and White*Prints in the black and white mode.
ColorPrints in the color mode.
PS Settings
Use the PS Settings menu to change printer settings that only affect jobs using the PostScript
emulation printer language.
Note:...

Values:
Off*Does not set the runtime of a PostScript job.
On 1 min.Sets the runtime of a PostScript job.
1-900 min.
Paper Select Mode
Purpose:
To set the way to select the paper tray for PostScript mode.
Values:
Auto*Automatically selects the paper tray for PostScript mode.
Select FromTrayManually selects the paper tray for PostScript mode.
Output Color
Purpose:
To set the default color for PostScript.
Values:
Color*Prints in color mode.
Black and WhitePrints in black and white mode.
Wired Network
Use...

Values:
Auto*Detects the Ethernet settings automatically.
10BASE-T HalfUses 10BASE-T Half-duplex.
10BASE- T FullUses 10BASE-T Full-duplex.
100BASE- TX HalfUses 100BASE-TX Half-duplex.
100BASE- TX FullUses 100BASE-TX Full-duplex.
1000BASE- T FullUses 1000BASE-T Full-duplex.
TCP/IP
Purpose:
To configure TCP/IP settings.
Values:
IP
ModeDual Stack*Uses both IPv4 and IPv6 to set the IP address.
IPv4Uses IPv4 to set the IP address.
IPv6Uses IPv6 to set the IP address.
Epson AcuLaser C2900 Series     User’s...

IPv4 Get IP Address DHCP /
Autonet*Sets the IP address automatically. A random value in the range of
169.254.1.0 to 169.254.254.255 that is not currently in use on the
network is set as the IP address. The subnet mask is set as 255.255.0.0.
BOOTPSets the IP address using BOOTP.
RARPSets the IP address using RARP.
DHCPSets the IP address using DHCP.
PanelUse this option when you want to set the IP address manually on the
operator panel.
IP AddressWhen an IP address is being set manually, the IP is...

Port9100 DisableDisables the Port9100 port.
Enable*Enables the Port9100 port.
IPP DisableDisables IPP port.
Enable*Enables IPP port.
SMB (TCP/IP) Disable*Disables SMB TCP/IP port.
EnableEnables SMB TCP/IP port.
WSD DisableDisables WSD port.
Enable*Enables WSD port.
SNMP (UDP/IP) DisableDisables the Simple Network Management Protocol (SNMP) UDP port.
Enable*Enables the SNMP UDP port.
StatusMessenger DisableDisables the E-Mail Alert feature.
Enable*Enables the E-Mail Alert feature.
InternetServices...

No. n / Mask (n is 1–5.)Sets the address mask for Filter n.
No. n / Mode (n is 1–
5.)Off*Disables the IP Filter feature for Filter n.
AcceptAccepts an access from the specified IP address.
RejectRejects an access from the specified IP address.
IEEE 802.1x
Note:
❏IEEE 802.1x feature is available only when the printer is connected using LAN cable and it is
available only when the IEEE 802.1 authentication is enabled.
❏To enable IEEE 802.1x, use “EpsonNet Config” on page 35. For details, refer to the Help...

TBCPSets the PostScript communications protocol to TBCP.
BinarySets the PostScript communications protocol to Binary.
USB Settings
Use the USB Settings menu to change printer settings affecting a USB port.
Note:
Values marked by an asterisk (*) are the factory default menu settings.
Port Status
Purpose:
To specify whether to enable the USB port. The change becomes effective after the printer is turned off
and then on again.
Values:
DisableDisables the USB interface.
Enable*Enables the USB interface....

Note:
Values marked by an asterisk (*) are the factory default menu settings.
Power Saver Time
Purpose:
To specify the time for transition to power saver mode.
Values:
Low Power
Timer3min*Specifies the time taken by the printer to enter Low Power mode after it finishes
a job.
3–60 min.
Sleep Timer 6min*Specifies the time taken by the printer to enter Sleep mode after it has entered
Low Power mode.
1–6 min.
Enter 5 to put the printer in power saver mode five minutes after it f in ishes  a job. This uses...