Home > Epson > Printer > Epson AcuLaser C2900DN User Manual

Epson AcuLaser C2900DN User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson AcuLaser C2900DN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Font Pitch
    Purpose:
    To specify the font pitch for scalable mono spaced fonts, within the range of 6.00 to 24.00. The default
    is 10.00.
    Font pitch refers to the number of fixed-space characters in a horizontal inch of type. For
    nonscheduled mono spaced fonts, the pitch is displayed, but cannot be changed.
    Note:
    The Font Pitch menu is only displayed for fixed or mono spaced fonts.
    Form Line
    Purpose:
    To set the number of lines in a page.
    Values:
    64*1 (mm series)/60*1 (inch series)Sets the value in increments of 1.
    5–128
    *1Denotes country-specific factory default values.
    The printer sets the amount of space between each line (vertical line spacing) based on the Form Line
    and Orientation menu items. Select the correct Form Line and Orientation before changing
    Form Line.
    Quantity
    Purpose:
    To set the default print quantity, within the range of 1 to 999. The default is 1. (Set the number of copies
    required for a specific job from the print driver. Values selected from the print driver always override
    values selected from the operator panel.)
    Image Enhance
    Purpose:
    To specify whether to enable the Image Enhance feature, which makes the boundary line between
    black and white smoother to decrease jagged edges and enhance the visual appearance.
    Epson AcuLaser C2900 Series     User’s Guide
    Using the Operator Panel Menus     111
     
    						
    							Values:
    On*Enables the Image Enhance feature.
    OffDisables the Image Enhance feature.
    Hex Dump
    Purpose:
    To help isolate the source of a print job problem. With Hex Dump selected, all data sent to the printer is
    printed in hexadecimal and character representation. Control codes are not executed.
    Values:
    Disable*Disables the Hex Dump feature.
    EnableEnables the Hex Dump feature.
    Draft Mode
    Purpose:
    To save toner by printing in the draft mode. The print quality is reduced when you print in the draft
    mode.
    Values:
    Disable*Does not print in the draft mode.
    EnablePrints in the draft mode.
    LineTermination
    Purpose:
    To add the line termination commands.
    Values:
    Off*The line termination command is not added.
    CR=CR, LF=LF, FF=FF
    Add-LFThe LF command is added.
    CR=CR-LF, LF=LF, FF=FF
    Epson AcuLaser C2900 Series     User’s Guide
    Using the Operator Panel Menus     112
     
    						
    							Add-CRThe CR command is added.
    CR=CR, LF=CR-LF, FF=CR-FF
    CR-XXThe CR and LF commands are added.
    CR=CR-LF, LF=CR-LF, FF=CR-FF
    Output Color
    Purpose:
    To specify the color mode to Color or Black and White. This setting is used for a print job that does
    not specify a print mode.
    Values:
    Black and White*Prints in the black and white mode.
    ColorPrints in the color mode.
    PS Settings
    Use the PS Settings menu to change printer settings that only affect jobs using the PostScript
    emulation printer language.
    Note:
    Values marked by an asterisk (*) are the factory default menu settings.
    PS Error Report
    Purpose:
    To specify whether to print the contents of PostScript errors.
    Values:
    OffDose not print the PS error report.
    On*Prints the PS error report.
    PS Job Time-out
    Purpose:
    To specify the runtime of one PostScript job.
    Epson AcuLaser C2900 Series     User’s Guide
    Using the Operator Panel Menus     113
     
    						
    							Values:
    Off*Does not set the runtime of a PostScript job.
    On 1 min.Sets the runtime of a PostScript job.
    1-900 min.
    Paper Select Mode
    Purpose:
    To set the way to select the paper tray for PostScript mode.
    Values:
    Auto*Automatically selects the paper tray for PostScript mode.
    Select FromTrayManually selects the paper tray for PostScript mode.
    Output Color
    Purpose:
    To set the default color for PostScript.
    Values:
    Color*Prints in color mode.
    Black and WhitePrints in black and white mode.
    Wired Network
    Use the Wired Network menu to change the printer settings affecting jobs sent to the printer through
    the wired network.
    Note:
    Values marked by an asterisk (*) are the factory default menu settings.
    Ethernet
    Purpose:
    To specify the communication speed and the duplex settings of Ethernet. The change becomes
    effective after the printer is turned off and then on again.
    Epson AcuLaser C2900 Series     User’s Guide
    Using the Operator Panel Menus     114
     
    						
    							Values:
    Auto*Detects the Ethernet settings automatically.
    10BASE-T HalfUses 10BASE-T Half-duplex.
    10BASE- T FullUses 10BASE-T Full-duplex.
    100BASE- TX HalfUses 100BASE-TX Half-duplex.
    100BASE- TX FullUses 100BASE-TX Full-duplex.
    1000BASE- T FullUses 1000BASE-T Full-duplex.
    TCP/IP
    Purpose:
    To configure TCP/IP settings.
    Values:
    IP
    ModeDual Stack*Uses both IPv4 and IPv6 to set the IP address.
    IPv4Uses IPv4 to set the IP address.
    IPv6Uses IPv6 to set the IP address.
    Epson AcuLaser C2900 Series     User’s Guide
    Using the Operator Panel Menus     115
     
    						
    							IPv4 Get IP Address DHCP /
    Autonet*Sets the IP address automatically. A random value in the range of
    169.254.1.0 to 169.254.254.255 that is not currently in use on the
    network is set as the IP address. The subnet mask is set as 255.255.0.0.
    BOOTPSets the IP address using BOOTP.
    RARPSets the IP address using RARP.
    DHCPSets the IP address using DHCP.
    PanelUse this option when you want to set the IP address manually on the
    operator panel.
    IP AddressWhen an IP address is being set manually, the IP is allocated to the
    printer using the format nnn.nnn.nnn.nnn. Each octet that makes up
    nnn.nnn.nnn.nnn is a value in the range of 0 to 254. 127 and any value in
    the range of 224 to 254 cannot be specified for the first octet of a
    gateway address.
    Subnet MaskWhen an IP address is being set manually, the subnet mask is specified
    using the format nnn.nnn.nnn.nnn. Each octet that makes up
    nnn.nnn.nnn.nnn is a value in the range of 0 to 255. 255.255.255.255
    cannot be specified as the subnet mask.
    Gateway AddressWhen an IP address is being set manually, the gateway address is
    specified using the format nnn.nnn.nnn.nnn. Each octet that makes up
    nnn.nnn.nnn.nnn is a value in the range of 0 to 254. 127 and any value in
    the range of 224 to 254 cannot be specified for the first octet of a
    gateway address.
    IPsec Disable*Disables IPsec.
    Note:
    To enable IPsec, use “EpsonNet Config” on page 35. For details, refer to the Help on the Software Disc.
    Protocol
    Purpose:
    To enable or disable each protocol. The change becomes effective after the printer is turned off and
    then on again.
    Values:
    LPD DisableDisables the Line Printer Daemon (LPD) port.
    Enable*Enables the LPD port.
    Epson AcuLaser C2900 Series     User’s Guide
    Using the Operator Panel Menus     116
     
    						
    							Port9100 DisableDisables the Port9100 port.
    Enable*Enables the Port9100 port.
    IPP DisableDisables IPP port.
    Enable*Enables IPP port.
    SMB (TCP/IP) Disable*Disables SMB TCP/IP port.
    EnableEnables SMB TCP/IP port.
    WSD DisableDisables WSD port.
    Enable*Enables WSD port.
    SNMP (UDP/IP) DisableDisables the Simple Network Management Protocol (SNMP) UDP port.
    Enable*Enables the SNMP UDP port.
    StatusMessenger DisableDisables the E-Mail Alert feature.
    Enable*Enables the E-Mail Alert feature.
    InternetServices DisableDisables an access to EpsonNet Config embedded in the printer.
    Enable* Enables an access to EpsonNet Config embedded in the printer.
    Bonjour(mDNS) DisableDisables Bonjour (mDNS).
    Enable*Enables Bonjour (mDNS).
    HTTP-SSL/TLS DisableDisables HTTP-SSL/TLS.
    Enable*Enables HTTP-SSL/TLS.
    IP Filter
    Note:
    IP Filter feature is available only when Protocol is set to LPD or Port9100.
    Purpose:
    To block data received from certain IP addresses through the wired network. You can set up to five IP
    addresses. The change becomes effective after the printer is turned off and then on again.
    Values:
    No. n / Address (n is 1–5.)Sets the IP address for Filter n.
    Epson AcuLaser C2900 Series     User’s Guide
    Using the Operator Panel Menus     117
     
    						
    							No. n / Mask (n is 1–5.)Sets the address mask for Filter n.
    No. n / Mode (n is 1–
    5.)Off*Disables the IP Filter feature for Filter n.
    AcceptAccepts an access from the specified IP address.
    RejectRejects an access from the specified IP address.
    IEEE 802.1x
    Note:
    ❏IEEE 802.1x feature is available only when the printer is connected using LAN cable and it is
    available only when the IEEE 802.1 authentication is enabled.
    ❏To enable IEEE 802.1x, use “EpsonNet Config” on page 35. For details, refer to the Help on the
    Software Disc.
    Purpose:
    To disable IEEE 802.1x authentication. The change becomes effective after the printer is turned off
    and then on again.
    Value:
    DisableDisables IEEE 802.1x.
    Initialize NVM
    Purpose:
    To initialize wired network data stored in non-volatile memory (NVM). After executing this function
    and rebooting the printer, all wired network settings are reset to their default values.
    Adobe Protocol
    Purpose:
    To set the PostScript communications protocol.
    Values:
    Auto*Sets the PostScript communications protocol automatically.
    StandardSets the PostScript communications protocol to Standard.
    BCPSets the PostScript communications protocol to BCP.
    Epson AcuLaser C2900 Series     User’s Guide
    Using the Operator Panel Menus     118
     
    						
    							TBCPSets the PostScript communications protocol to TBCP.
    BinarySets the PostScript communications protocol to Binary.
    USB Settings
    Use the USB Settings menu to change printer settings affecting a USB port.
    Note:
    Values marked by an asterisk (*) are the factory default menu settings.
    Port Status
    Purpose:
    To specify whether to enable the USB port. The change becomes effective after the printer is turned off
    and then on again.
    Values:
    DisableDisables the USB interface.
    Enable*Enables the USB interface.
    Adobe Protocol
    Purpose:
    To set the PostScript communications protocol.
    Values:
    AutoSets the PostScript communications protocol automatically.
    StandardSets the PostScript communications protocol to Standard.
    BCPSets the PostScript communications protocol to BCP.
    TBCP*Sets the PostScript communications protocol to TBCP.
    BinarySets the PostScript communications protocol to Binary.
    System Settings
    Use System Settings to configure a variety of printer features.
    Epson AcuLaser C2900 Series     User’s Guide
    Using the Operator Panel Menus     119
     
    						
    							Note:
    Values marked by an asterisk (*) are the factory default menu settings.
    Power Saver Time
    Purpose:
    To specify the time for transition to power saver mode.
    Values:
    Low Power
    Timer3min*Specifies the time taken by the printer to enter Low Power mode after it finishes
    a job.
    3–60 min.
    Sleep Timer 6min*Specifies the time taken by the printer to enter Sleep mode after it has entered
    Low Power mode.
    1–6 min.
    Enter 5 to put the printer in power saver mode five minutes after it f in ishes  a job. This uses much less
    energy, but requires more warm-up time for the printer. Enter 5 if your printer shares an electrical
    circuit with room lighting and you notice lights flickering.
    S e l e c t  a  h i g h  v a l u e  i f  y o u r  p r i n t e r  i s  i n  c o n s t a n t  u s e .  I n  m o s t  c i r c u m s t a n c e s ,  t h i s  k e e p s  t h e  p r i n t e r  r e a d y
    to operate with minimum warm-up time. Select a value between 5 and 30 minutes for power saver
    mode if you want a balance between energy consumption and a shorter warm-up period.
    The printer automatically returns to the standby mode from the power saver mode when it receives
    data from the computer. You can also change the status of the printer to the standby mode by pressing
    the 
     (Energy Saver) button on the operator panel.
    Auto Reset
    Purpose:
    To automatically reset the settings to the default settings and return to the standby mode after you do
    not specify any settings for the specified time.
    Values:
    45sec*
    1min
    2min
    3min
    Epson AcuLaser C2900 Series     User’s Guide
    Using the Operator Panel Menus     120
     
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson AcuLaser C2900DN User Manual