Home > Epson > Printer > Epson AcuLaser C2800DN User Manual

Epson AcuLaser C2800DN User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson AcuLaser C2800DN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							AcuLaser C2800 Series Users Guide
    Installing Options191
    Note for Macintosh users:
    When you have attached or removed printer options, you need to delete the printer using Print Setup 
    Utility (for Mac OS X 10.3 and 10.4) or Print Center (for Mac OS X 10.2), and then re-register the printer.
    Removing the optional paper cassette unit
    Perform the installation procedure in reverse.
    Duplex Unit
    For specifications or details about the paper types and sizes that you can use with the Duplex Unit, 
    see “Duplex Unit” on page 269.
    Installing the Duplex Unit
    Follow the steps below to install the optional Duplex Unit.
    1. Turn off the printer.
    *OFF
    *
     
    						
    							AcuLaser C2800 Series Users Guide
    Installing Options192
    2. Press the latch on the front cover and open the cover.
    c
    Caution:
    ❏Do not leave the front cover open for more than five minutes to avoid exposing the imaging 
    cartridges to light.
    ❏Do not expose the imaging cartridges to sunlight at all.
    3. Remove the cap from the connector.
     
    						
    							AcuLaser C2800 Series Users Guide
    Installing Options193
    4. Pull up the blue tabs on both sides of the transfer unit.
    c
    Caution:
    Do not touch the transfer belt on the transfer unit to avoid damaging it.
    5. Raise the transfer unit.
    6. Take the Duplex Unit out of its package.
     
    						
    							AcuLaser C2800 Series Users Guide
    Installing Options194
    7. Insert the tabs on the Duplex Unit into the printer, align the arrow marks and push it down to 
    connect the connector.
    8. Pull down the transfer unit.
    9. Close the front cover.
    10. Turn on the printer.
    To confirm that the option is installed correctly, print a Status Sheet. See “Printing a Status Sheet” 
    on page 237.
    Note:
    The printer cannot recognize the Duplex Unit if its cover has not been removed. Make sure that the cover was 
    removed as explained in step 3.
     
    						
    							AcuLaser C2800 Series Users Guide
    Installing Options195
    Note for Windows users:
    If EPSON Status Monitor is not installed, you have to make settings manually in the printer driver. See 
    “Making Optional Settings” on page 71.
    Note for Macintosh users:
    When you have attached or removed printer options, you need to delete the printer using Print Setup 
    Utility (for Mac OS X 10.3 and 10.4) or Print Center (for Mac OS X 10.2), and then re-register the printer. 
    For Windows, see “Printing with the Duplex Unit (models with Duplex Unit only)” on page 55, For 
    Macintosh, see “Printing with the Duplex Unit (models with Duplex Unit only)” on page 118 for 
    information about duplex printing.
    Removing the Duplex Unit
    Follow the steps below to remove the optional Duplex Unit.
    1. Turn off the printer.
    2. Press the latch on the front cover and open the cover.
    3. Pull up the blue tabs on both sides of the transfer unit.
    4. Raise the transfer unit.
    5. Grasp the handle to unlock the Duplex Unit and remove it from the printer.
    6. Pull down the transfer unit.
    7. Turn on the printer.
     
    						
    							AcuLaser C2800 Series Users Guide
    Installing Options196
    Memory Module
    By installing a Dual In-line Memory Module (DIMM), you can increase printer memory up to 
    640 MB. You may want to add additional memory if you are having difficulty printing complex 
    graphics.
    Installing a memory module
    Follow the steps below to install an optional memory module.
    c
    Caution:
    Before you install a memory module, be sure to discharge any static electricity by touching a grounded 
    piece of metal. Otherwise, you may damage static-sensitive components.
    w
    Warning:
    Be careful when working inside the printer as some components are sharp and may cause injury.
    1. Remove the interface cover on the back of the printer.
     
    						
    							AcuLaser C2800 Series Users Guide
    Installing Options197
    2. Turn the printer off and unplug the power cord and all the interface cables.
    *OFF
    c
    Caution:
    Make sure to unplug the power cord from the printer to prevent getting an electrical shock.
    3. Loosen the two screws on the back of the printer.
    *
     
    						
    							AcuLaser C2800 Series Users Guide
    Installing Options198
    4. Remove the controller option expanded aperture plate.
    5. Identify the memory slots. These positions are shown below.
    S1. Optional memory slot
    S0. Standard memory slot
    Note:
    Do not remove the memory module from the S0 slot.
    S1S0
     
    						
    							AcuLaser C2800 Series Users Guide
    Installing Options199
    6. Hold the memory module and insert it into the optional memory slot in the orientation shown 
    below until it stops. Then press both sides of the memory module down. Confirm that the notch 
    on the memory module matches that of the memory slot.
    *notch
    c
    Caution:
    ❏Do not apply too much force.
    ❏Be sure to insert the memory facing the correct way.
    ❏Do not remove any modules from the circuit board. Otherwise, the printer will not work.
    7. Reattach the controller option expanded aperture plate.
    *
     
    						
    							AcuLaser C2800 Series Users Guide
    Installing Options200
    8. Fasten the cover with the two screws.
    9. Reconnect all the interface cables and the power cord.
    10. Reattach the interface cover.
    11. Plug the printer’s power cord into an electrical outlet.
    12. Turn on the printer.
    To confirm that the option is installed correctly, print a Status Sheet. See “Printing a Status Sheet” 
    on page 237.
    Note for Windows users:
    If EPSON Status Monitor is not installed, you have to make settings manually in the printer driver. See 
    “Making Optional Settings” on page 71.
    Note for Macintosh users:
    When you have attached or removed printer options, you need to delete the printer using Print Setup 
    Utility (for Mac OS X 10.3 and 10.4) or Print Center (for Mac OS X 10.2), and then re-register the printer.
     
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson AcuLaser C2800DN User Manual