Epson AcuLaser C1750N User Manual

Auto Log Print
Purpose: 
To automatically print a job history report after every 10 jobs.
Values:
Off*Does not automatically print a job history report.
OnAutomatically prints a job history report.
Note:
The Job History report can also be printed using the Information Pgs menu.
mm/inch
Purpose: 
To specify the measurement unit displayed after the numeric value on the operator panel.
Values:
millimeter(mm)*Specifies the default measurement unit.
inch(")
Def. Paper Size
Purpose: 
To specify the default...

Values:
OffDoes not show the alert message when the toner is low.
On*Shows the alert message when the toner is low.
Maintenance Mode
Use the Maintenance Mode menu to initialize Non-Volatile Memory (NVM), configure the plain
paper quality adjustment settings, and configure the security settings.
Note:
Values marked by an asterisk (*) are the factory default menu settings.
F/W Version
Purpose: 
To display the version of the controller.
Adjust PaperType
Purpose: 
To adjust the paper type.
Values:
Plain...

Note:
The print quality changes depending on the values you select for this item.
Values:
Plain 0*
-3 – +3
Bond 0*
-3 – +3
Light Card 0*
-3 – +3
Labels 0*
-3 – +3
LW Gloss Card 0*
-3 – +3
Envelope 0*
-3 – +3
Recycled 0*
-3 – +3
Adj. Fusing Unit
Purpose: 
To specify the optimum temperature settings for printing for the fusing unit. To lower the
temperature, set negative values. To increase, set positive values.
The default settings may not give the best output on all paper types. When the printed paper...

Values:
Plain 0*
-3 – +3
Bond 0*
-3 – +3
Light Card 0*
-3 – +3
Labels 0*
-3 – +3
LW Gloss Card 0*
-3 – +3
Envelope 0*
-3 – +3
Recycled 0*
-3 – +3
Auto Regi Adj
Purpose: 
To specify whether to automatically adjust color registration.
Values:
OffDoes not automatically adjust color registration.
On*Automatically adjusts color registration.
Adjust ColorRegi
Purpose: 
To specify whether to manually adjust color registration.
Color registration adjustments need to be made during the initial setup of the...

Values:
Auto AdjustAutomatically corrects color registration.
Color Regi ChartPrints a color registration chart. The color registration chart prints a lattice pattern of yellow,
magenta, and cyan lines. On the chart, find the values on the right side that are next to the line
that is perfectly straight for each of the three colors. If the value for this line is 0, color registration
is not needed. If the value for this line is any value other than 0, specify the adjustment values
under Enter Number....

Values:
Off*Does not automatically execute counter measures for curling/separating
discharge of the paper.
OnAutomatically executes counter measures for curling/separating discharge of
the paper.
Chart
Purpose: 
To print various charts that can be used for diagnosing your printer.
Values:
GhostPrints a chart to check for ghost printing.
4ColorsPrints bands of yellow, magenta, cyan, and black with varying density.
AlignmentPrints a chart, and then check for proper alignment of the print image on the...

Values:
Off*Does not use toner cartridge of another manufacturer.
OnUses toner cartridge of another manufacturer.
Adjust Altitude
Purpose: 
To specify the altitude of the location where the printer is installed.
The discharge phenomenon for charging the photo conductor varies with barometric pressure.
Adjustments are performed by specifying the altitude of the location where the printer is being used.
Note:
An incorrect altitude adjustment setting leads to poor printing quality, incorrect indication of...

See Also:
“Panel Lock Function” on page 149
Values:
Disable*Does not restrict access to the operator panel menus.
EnableRestricts access to the operator panel menus with a password.
New
PasswordSets a password required to access the operator panel menus.
Re-enterEnters the new password again to confirm.
Change Password
Purpose: 
To change a password to limit access to the operator panel menus.
Values:
Current PasswordEnter the current password to change the password.
New PasswordEnter the new password....

 Panel Language
Note:
Values marked by an asterisk (*) are the factory default menu settings.
Purpose: 
To specify the language to be used on the operator panel.
See Also:
“Adjusting the Language” on page 128
Values:
English*
Français
Italiano
Deutsch
Español
Nederlands
Português
Türkçe
Panel Lock Function
This feature prevents unauthorized users from changing settings made by the administrator.
However, you can select settings for individual print jobs using the print driver.
Enabling the Panel Lock
1....

3. Select Secure Settings, and then press the  button.
4. Select Panel Lock, and then press the 
 button.
5. Select Panel Lock Set, and then press the 
 button.
6. Select Enable, and then press the 
 button.
7. Enter the new password, and then press the 
 button.
8. Re-enter the password to confirm the password that you entered, and then press the 
 button.
Note:
❏If you forget your password, turn off the printer. Then, while holding the 
 (Menu) button, turn on
the printer. Continue to hold the 
 (Menu)...