Epson AcuLaser C1750N User Manual

10. Insert the PSI into the printer and then align the PSI to the marking on the MPF.
11. Open the output tray extension.
12. Select the paper type from the print driver if the loaded print media is not standard plain paper. If a
user-specified print media is loaded in the MPF, you must specify the paper size setting by using
the print driver.
Epson AcuLaser C1750 Series     User’s Guide
Printing Basics     101
 

Note:
For more information about setting the paper size and type on the print driver, refer to the online
Help provided for the print driver.
Note:
For standard-size paper, adjust the guides first and then set paper.
Loading Envelope in the Multipurpose Feeder (MPF)
Note:
When you print on envelopes, be sure to specify the envelope setting on the print driver. If not specified,
the print image will be rotated 180 degrees.
When Loading # 10, DL, or Monarch
Load envelopes with the side to be p r i n t e d...

Note:
When you load the envelopes in the long-edge feed (LEF) orientation, be sure to specify the landscape
orientation on the print driver.
When Loading C5
Load envelopes with the side to be printed on facing up, flap opened, and facing you.
Important:
Never use envelopes with windows, or coated linings. These lead to paper jams and can cause damage to
the printer.
Note:
❏If you do not load envelopes in the MPF right after they have been removed from the packaging, they
may bulge. To avoid jams, flatten...

❏If envelopes are still not fed correctly, add some bending to the flap of the envelopes as shown in the
following illustration.
The amount of the bending shall be 5 mm (0.20 inches) or less.
❏To confirm the correct orientation of each print media such as envelopes, see the instruction on the
Envelope/Paper Setup Navigator on the print driver.
Epson AcuLaser C1750 Series     User’s Guide
Printing Basics     104
 

Loading Letterhead in the Multipurpose Feeder (MPF)
Load the letterhead in the printer with the print side facing up. Ensure that the title on the letterhead
enters the printer first.
Loading Print Media in the Priority Sheet Inserter (PSI)
Note:
❏To avoid paper jams, do not remove the PSI while printing is in progress.
❏Use only laser print media. Do not use ink jet paper in this printer.
1. Open the front cover.
Epson AcuLaser C1750 Series     User’s Guide
Printing Basics     105
 

2. Slide the PSI forward, and then align the PSI to the marking on the MPF.
3. Adjust the paper width guides to their maximum width.
4. Before loading the print media, flex the sheets back and forth, and then fan them. Straighten the
edges of the stack on a level surface.
Epson AcuLaser C1750 Series     User’s Guide
Printing Basics     106
 

5. Load print media on the PSI with the top edge first and with the recommended print side facing
up.
6. Adjust the paper width guides until they rest lightly against the edges of the stack of print media.
7. Open the output tray extension.
Epson AcuLaser C1750 Series     User’s Guide
Printing Basics     107
 

8. Select the paper type from the print driver if the loaded print media is not standard plain paper. If a
user-specified print media is loaded in the PSI, you must specify the paper size setting by using the
print driver.
Note:
For more information about setting the paper size and type on the print driver, refer to the online Help
provided for the print driver.
Loading Envelope in the Priority Sheet Inserter (PSI)
Note:
❏Be sure to fully insert the envelope until it stops. Otherwise, print media that is...

When Loading C5
Load the envelope with the side to be printed on facing up, flap opened, and facing you.
Important:
Never use envelopes with windows, or coated linings. These lead to paper jams and can cause damage to
the printer.
Note:
❏If you do not load envelopes in the PSI right after they have been removed from the packaging, they
may bulge. To avoid jams, flatten them as shown below when loading them in the PSI.
Epson AcuLaser C1750 Series     User’s Guide
Printing Basics     109
 

❏If envelopes are still not fed correctly, add some bending to the flap of the envelopes as shown in the
following illustration.
The amount of the bending shall be 5 mm (0.20 inches) or less.
❏To confirm the correct orientation of each print media such as envelopes, see the instruction on the
Envelope/Paper Setup Navigator on the print driver.
Epson AcuLaser C1750 Series     User’s Guide
Printing Basics     110