Epson AcuLaser C1750N User Manual

Chapter 5
Printing Basics
About Print Media
Using paper that is not appropriate for the printer can cause paper jams, image quality problems, or
printer failure. To achieve the best performance from your printer, we recommend you to use only the
paper described in this section.
When using paper other than that recommended, contact the Epson local representative office or an
authorised dealer.
Print Media Usage Guidelines
The printer tray accommodates various sizes and types of paper and other specialty...

See Also:
❏“Loading Print Media in the Multipurpose Feeder (MPF)” on page 96
❏“Loading Print Media in the Priority Sheet Inserter (PSI)” on page 105
❏“Loading Envelope in the Multipurpose Feeder (MPF)” on page 102
❏“Loading Envelope in the Priority Sheet Inserter (PSI)” on page 108
❏“Printing on Custom Size Paper” on page 123
Print Media That Can Damage Your Printer
Your printer is designed to use a variety of media types for print jobs. However, some media can cause
poor output quality, increased paper...

Important:
The toner may come off the print media, if it gets wet by water, rain, steam and so on. For details, contact
the Epson local representative office or an authorized dealer.
Usable Print Media
The types of print media that can be used on this printer are as follows:
Note:
❏SEF and LEF indicate the paper feed direction; SEF stands for short-edge feed. LEF stands for
long-edge feed.
❏Use only laser print media. Do not use ink jet paper in this printer.
❏Printing on print media that differs from...

Paper Type (Weight) Plain
Bond
Lightweight Cardstock
Lightweight Glossy Cardstock
Labels
Envelope
Recycled
Letterhead
Pre-Printed
Hole Punched
Colored
Special
Custom Type
Loading Capacity 150 sheets of standard paper
*1 Monarch and DL envelopes can be supported by LEF with their flap open.
*2 The maximum width is 220 mm for DL LEF.
*3 The minimum length is 3.875 inches for Monarch LEF and 110 mm for DL LEF.
Priority Sheet Inserter (PSI)
Paper Size
A4 SEF (210 × 297 mm)
B5 SEF (182 × 257 mm)
A5 SEF (148 ×...

Paper Type (Weight) Plain
Bond
Lightweight Cardstock
Lightweight Glossy Cardstock
Labels
Envelope
Recycled
Letterhead
Pre-Printed
Hole Punched
Colored
Special
Custom Type
Loading Capacity 10 sheets of standard paper
Loading Print Media
Loading print media properly helps prevent jams and ensures trouble-free printing.
Before loading print media, identify the recommended print side of the print media. This information
is usually on the print media package.
Note:
After loading paper in the feeder, specify...

❏16.2 mm (0.64 inches) of labels
Priority sheet inserter (PSI) can hold:
❏10 sheets of standard paper or one sheet of other paper
Print Media Dimensions
The MPF accepts print media within the following dimensions:
❏Width: 76.2 – 215.9 mm (3.00 – 8.50 inches)
❏Length: 127 – 355.6 mm (5.00 – 14.00 inches)
Note:
❏The maximum width is 220 mm for DL LEF.
❏The minimum length is 3.875 inches for Monarch LEF and 110 mm for DL LEF.
The PSI accepts print media within the following dimensions:
❏Width: 76.2 – 215.9...

1. Open the front cover.
Note:
When you use the MPF for the first time, open the front cover by pulling out the instruction sheet.
2. Pull the PSI out.
Epson AcuLaser C1750 Series     User’s Guide
Printing Basics     97
 

Note:
❏When you use the MPF for the first time, remove the instruction sheet attached to the PSI with
adhesive tape.
❏Read the instruction sheet before you use the PSI.
3. Pull the slide bar forward until it stops.
4. Pull the length guide forward until it stops.
Epson AcuLaser C1750 Series     User’s Guide
Printing Basics     98
 

5. Adjust the paper width guides to their maximum width.
6. Before loading the print media, flex the sheets back and forth, and then fan them. Straighten the
edges of the stack on a level surface.
7. Load print media on the MPF with the top edge first and with the recommended print side facing
up.
Epson AcuLaser C1750 Series     User’s Guide
Printing Basics     99
 

8. Adjust the paper width guides until they rest lightly against the edges of the stack of print media.
9. Slide the length guide towards the printer until it touches the print media.
Note:
Depending on the size of print media, first slide the slide bar backward until it stops, and then pinch
the length guide and slide it backward until it touches print media.
Epson AcuLaser C1750 Series     User’s Guide
Printing Basics     100