Epson AcuLaser C1750N User Manual

When IPv4 is selected:
❏Configure the following:
a
Select Type.
b Enter the following items:
❏IP Address of your printer
❏Network Mask
❏Gateway Address
When IPv6 is selected:
❏Configure the following:
a
Select Use Manual Address.
b Enter IP address of your printer.
c Enter the gateway address of your network.
When Dual Stack is selected:
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     51
 

Configure the IPv4 Settings and IPv6 Settings.
8. Click Next.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     52
 

9. Ensure that the wireless settings are displayed, and then click Apply.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     53
 

The Complete configuration screen appears.
10. Wait a few minutes until the printer restarts to establish the wireless network.
11. Print a Printer Settings page from the operator panel.
See “Printing a Printer Settings Page” on page 125.
12. Confirm that “Wireless Status” is shown as “Good”, “Acceptable” or “Low” on the report.
Note:
When “Wireless Status” is “No Reception”, check if the wireless settings are correctly configured. To
reconfigure the wireless settings, click Next on the Complete...

If you see any errors, click Trouble Shooting Guide and follow the instruction.
16. Check if the printer to be installed is listed in the Select Printer screen, and then click Next.
Note:
If the printer to be installed is not listed in the Select Printer screen, try the following steps:
❏Click Refresh to update the information.
❏Click Manually add using IP address, and then enter the details of the printer manually.
17. Configure the required items on the Enter Printer Settings screen, and then click...

The wireless configuration is complete.
WPS-PIN
Note:
WPS-PIN (Wi-Fi Protected Setup-Personal Identification Number) is a method to authenticate and
register devices required for wireless configuration, by entering PIN assignments to a printer and
computer. This setting, performed through access point, is available only when the access points of your
wireless router supports WPS.
1. Select WPS-PIN, and then click Next.
2. Follow the instructions until the Check Setup screen appears.
3. Confirm there are...

4. Check if the printer to be installed is listed in the Select Printer screen, and then click Next.
Note:
If the printer to be installed is not listed in the Select Printer screen, try the following steps:
❏Click Refresh to update the information.
❏Click Manually add using IP address, and then enter the details of the printer manually.
5. Configure the required items on the Enter Printer Settings screen, and then click Next.
6. Select the software to be installed, and then click Install.
The...

If you see any errors, click Trouble Shooting Guide and follow the instruction.
4. Check if the printer to be installed is listed in the Select Printer screen, and then click Next.
Note:
If the printer to be installed is not listed in the Select Printer screen, try the following steps:
❏Click Refresh to update the information.
❏Click Manually add using IP address, and then enter the details of the printer manually.
5. Configure the required items on the Enter Printer Settings screen, and then click...

The wireless configuration is complete.
Note:
For WPS-PBC operation on the wireless LAN access point, refer to the manual supplied with the wireless
LAN access point.
When the WPS-PBC operation is successful and the printer is rebooted, wireless LAN connection is
completed.
Operator Panel
1. Select Operator Panel, and then click Next.
2. Follow the instructions until the Check Setup screen appears.
3. Confirm there are no errors displayed on the LCD panel, and then click Start Installation.
If you see...

4. Check if the printer to be installed is listed in the Select Printer screen, and then click Next.
Note:
If the printer to be installed is not listed in the Select Printer screen, try the following steps:
❏Click Refresh to update the information.
❏Click Manually add using IP address, and then enter the details of the printer manually.
5. Configure the required items on the Enter Printer Settings screen, and then click Next.
6. Select the software to be installed, and then click Install.
The...