Eiki Projector Lc Hdt700 User Manual

31
ENGLISH
 
SNMP setting
Check and delete the trap address
Checking  the  registered  trap  address  and 
deleting the address.
To  delete  the  address,  tick  check  box  in  front 
of the IP address and click Delete button.
✐ Up to 10 trap addresses can be registered.
Trap check/delete
Trap option
Trap option setting
Tick check boxes in front of the condition item 
to send the trap. 
✐  Click Set button if you tick or un-tick the check 
box on a page.
✐		 "When PJ lamp is off " signifies the...

32
Chapter 3 Basic Setting and Operation 

ENGLISH
33
ENGLISH
Chapter 4 
 Controlling the Projector4
Describes controlling and setting of the projector by using the web 
browser. 

34
Chapter 4 Controlling the Projector
Power control and status check
 Click Power  &  Status  on  the  main  menu.  The  control  page  will  be  dis -
played.
By clicking  ON or Standby  button on the page, the power of the projector 
can be controlled. 
Item     Description
PJ status
  Power   .........................   Displays the status of the lamp. (ON, OFF, On starting up, On cooling down, 
Service in need)
  Status  ..........................   Displays the status of the projector's power....

35
ENGLISH
 
About projector condition
Status Description
Normal  ............................................................... Projector is operating normally.
Power management in operation ........... Power management is operating
Lamp failure  ................................................... Lamp failure is occurring
Abnormal temperature  .........................The temperature of the projector became too high
Standby after Abnormal Temp.  ........ 
Projector detects abnormal temp. and sets into...

36
Chapter 4 Controlling the Projector
Control
Click Control   on  the  main  menu.  The  setting  method  differs  depending 
on  the  contents  of  the  page.  Click  on  the  page  number  to  change  pages 
and select desired setting items.
✐   Please  see  the  owner's  manual  of  the  projector  to  have  the  further  information 
of each control item. 
 
✐   The control page displays valid control items depending on the selected input mode, signal 
or  functions of the projector you use,...

37
ENGLISH
 
System
This  function  is  to  select  the  system  of  signal 
input  to  the  projector.  The  available  system 
mode  are  listed  on  the  pull-down  menu  but-
ton  according  to  the  input  signal.  Selec t  a 
system and then click Set  button.
Control
✐  If the mode (Mode1 to Mode10) which is stored in the item "PC Adjustment" ( + p.39) is available, 
they are also listed together with the above mode.
Available selection at the RGB(PC analog) input
Item   Description
XGA1...

38
Chapter 4 Controlling the Projector
Item  Description
Contrast  ..............................  
Adjusts picture con-
trast. (0~ 63)
Brightness  .........................  Adjusts picture bright -
ness. (0~ 63)
Color  ......................................  
Adjusts picture color 
saturation. (0~ 63)
Tint  .........................................   Adjusts picture hue. 
(0~ 63)
Color temp.  .......................
  Sets a color temperature 
mode. (X Low, Low, Mid, 
High, Adj.)
White balance
 Red,...

39
ENGLISH
 
PC adjustment
PC adjustment
Click PC  Adj.   on  the  main  menu.  This  function  is  to  adjust  the  signal  from 
the  computer  connected  to  the  projector  to  obtain  the  proper  picture 
image on the screen. 
Item   Description
Current mode  ...... 
Displays a current mode like VGA, SVGA, XGA. SXGA, UXGA, WXGA, etc. or Mode1 - Mode10 
which are the customized mode created by using the "Mode Store" function described 
below.
Auto PC adj..........   Performs automatic...

40
Chapter 4 Controlling the Projector
Setting up the projector
Click Setting   on  the  main  menu.  This  function  is  to  set  up  the  projector. 
Select the sub menu [Screen setting] or [Setting] and then set up each set -
ting.
Item   Description
Screen  .....................  
Switches the screen mode. (Normal, Full, 
Wide(16:9), Zoom, True, Natural wide, 
Custom)
Ceiling  .....................   Sets the image top/bottom and left/
right reversed. (ON, OFF)
Rear  ..............................