Eiki Projector Lc Hdt700 User Manual

21
ENGLISH
 
How to use the setting page
Radio button setting
Select an item by selecting a radio 
button.
Check box setting
Select items by ticking on check 
boxes. 

22
Chapter 3 Basic Setting and Operation
Initial setting
After installing the projector, perform the following basic initial setting.
Click Initial Setting on the main menu to display the initial setting page.
Item  Description
Language  .............. 
Switches display language on the setting page. (Japanese, English)
Model name  ....... 
Indicates the model name of the projector
SERIAL NO.   ..........Indicates the serial number of the projector
Network PIN code  ......
 
Sets the Network PIN code to...

23
ENGLISH
 
Initial setting
Network PIN code setting
This  is  to  set  the  Network  PIN  code  to  restrict 
the  access  from  an  unauthorized  person 
through the network. 
Enter  a  4- digit  number  as  the  Net work  PIN 
code onto the text box and click Set button. 
   The  projector  begins  restar ting  and  it  takes 
about  10  seconds.  Close  (Quit)  the  web  browser  and  access  to  the  login  page  again  in  10 
seconds. This is to perform the login authentication firmly.
The...

24
Chapter 3 Basic Setting and Operation
Network configuration
Click Network  on the main menu. The following setting page is displayed. 
The IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server) 
and projector name are set up on this menu.
The  IP  address  and  Subnet  Mask  have  been  configured  already  in  chapter 
"Installation".  If  you  want  to  change  them  or  configure  default  gateway  or  DNS,  perform 
them in this page. If you change them, the projector begins...

25
ENGLISH
 
Item  Description
IP address  ................ 
Control System IP Address 
as a string. The default 
value is blank.
IP ID  ..............................   Control System IP ID as a 
string. The default value is 
blank.  
(from 3 to 254)
Port  ...............................   The default value is 41794.  
(from 1 to 65535)
Network configuration
You can use Crestron RoomView® to monitor 
and control the projector through the net -
work.
For more information, visit http://www.
crestron.com &...

26
Chapter 3 Basic Setting and Operation
E-mail setting
This  projector  has  an  E-mail  function  which  can  send  an  alert  message 
to  users  or  an  administrator  if  it  detects  an  abnormality  on  the  projector 
or  run  out  of  the  life  span  of  the  lamp.  Click E-mail  Setting  on  the  main 
menu and follow the below steps.
Item   Description
SMTP server  ........................... 
Enter server name or IP address of the SMTP server. (up to 60 characters)SMTP server port...

27
ENGLISH
 
E-mail setting
✐  If the projector sends an alert message due to the abnormality on the projector but the SMTP 
server is down in some other reason, the message will not be sent. In this case, the message 
"Unable to connect to server." will be displayed on the setting page. To clear this message, set up 
SMTP server address again.
✐  To use the E-Mail function, it must be set the DNS address on the Network setting page correctly.
✐   You cannot use this E-mail function if the DNS...

28
Chapter 3 Basic Setting and Operation
✐		"When PJ lamp is off " signifies the lamp goes out without user operation. "When PJ is turned into 
Standby  in proper user operation" signifies that the projector is turned on by using the web browser 
and then it is turned into standby with ON/STANDBY button on the side control or the remote control.
✐	Up to 99,999 hours can be set for use time.
Option5  Option selection for sending alert mail
Click  Option  sub menu tab. Check the con -...

29
ENGLISH
 
E-mail setting
● When PJ lamp replacement time is reached:
✐  Replace it with a new lamp immediately and reset the lamp counter. If the projector is 
used without resetting the lamp counter, the alert mail is sent to users in every power-
on of the projector. This alert mail will not be sent when unchecking the mail sending 
condition "When PJ lamp replacement time is reached".
TITLE: Message from projector
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector Name:...

30
Chapter 3 Basic Setting and Operation
SNMP setting
This  projector  provides  a  SNMP  (Simple  Network  Management  Protocol) 
agent  function.  The  SNMP  consists  of  a  manager  and  agents.  The  group 
which  communicates  information  each  other  with  SNMP  is  called 
"Community".  There  are  two  access  modes  in  a  community,  Refer  (read  only)  and  Set  (read- 
write). This projector allows to use Refer (read only) only. The SNMP message informs the pro -
jector  status...