Eiki Projector Lc Hdt1000 User Manual

1

Remote Control
POINT buttons
KEYSTONE button
Press the KEYSTONE button on the remote control to switch 
the Standard (for Vertical/Horizontal) /Corner correction 
adjustment. The Standard or Corner correction adjustment 
dialog box appears. Use the Point ed 7 8 buttons to 
correct the Standard or Corner distortion. The Standard or 
Corner correction adjustment can be stored (see pages 45, 
52).
✔Note:
• The white arrows indicate that there is no 
correction.
•  A red arrow indicates the...



The input source changes each time you press the INPUT button on the side control as follows:
 Input 1→Input 2→ ...
Before using the INPUT button on the side control or the remote control, you must select a correct input source 
by On-Screen Menu and the latest input source will be displayed.
Press the INPUT 1, INPUT 2, INPUT 3 or  INPUT 4 button on the remote control. The input source appears on 
the screen as you press each button. Select the connected input source.
INPUT 1 button
Input 1...



WHEN SELECTING INPUT  (5 BNC INPUT JACKS )
INPUT MENU
When your computer is connected to the INPUT 1 
(ANALOG) terminal, select RGB (PC analog).
RGB(PC analog)
✔Note:
• Input  source  changes  if  the  INPUT  1  button  on  the  remote 
control is pressed.
When connecting the computer output [5 BNC Type (Green, 
Blue, Red, Horiz. Sync, and Vert. Sync.)] from the computer 
to G, B, R, H/HV, and V jacks:
When your computer is connected to the INPUT 2 (5 
BNC INPUT JACKS) terminal, select...

4

Input Selection
When the video input signal is connected 
to the Y, Pb/Cb, Pr/Cr jacks, select Y, Pb/
Cb, Pr/Cr.
When the video input signal is connected 
to the VIDEO jack, select Video.
When connecting to video equipment, select the type of 
Video source in the Source Select Menu. 
Video
y, Pb/Cb, Pr/Cr
When connecting to video equipment, select the type of 
Video source in the Source Select Menu. 
INPUT 1 MENU
HDMI
RGB(Scart)
When scart video equipment is connected to the INPUT 1 
(ANALOG)...

5

Computer Input
PC System Menu
PC System Menu
1

PC system can also be selected manually.
Selected system is displayed.
Press the MENU button to display the on-screen menu. 
Use the Point ed buttons to select Input and then 
press the Point 8 or the SELECT button. 
Use the Point ed buttons to select System and then 
press the Point 8 or the SELECT button.
Use the Point ed buttons to select the desired system 
and then press the SELECT button.
Systems in this dialog box can be selected....

6

Computer Input
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Position H and Position V 
to conform to your computer. 
To store the adjusted parameters.The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting Mode in PC System Menu (p.35). See “Manual PC Adjustment” on pages 37, 38.
✔Note:
 •  Fine  sync, Total  dots,  Position  H  and  Position  V    of...

7

Computer Input
Some computers employ special signal formats which may not be tuned by Multi-Scan system of this projector. 
Manual PC Adjustment enables you to precisely adjust several parameters to match those special signal formats. 
The projector has 10 independent memory areas to store those parameters manually adjusted. It allows you to 
recall the setting for a specific computer. 
Use  the  Point 7 8 buttons  to  adjust  the  value,  eliminating  a 
flicker from the image displayed (from 0...



Computer Input
✔Note
• Display area (H/V) cannot be selected when 480i, 575i, 480p, 
575p,  720p,  1035i  ,  1080i  or  1080p  is  selected  in  the  PC 
System Menu (p.35).
•  When  input  computer  signal  to  the  projector,  PC  adjust 
function will become available.
No parameters stored
This mode has stored parameters.
Values of Total dots, Position H, Position V, Display area H and Display area V.
Press the SELECT button 
to store the data.
Press the MENU button 
to close this dialog...

9

1

Normal picture level preset on the projector.
Picture level with improved halftone for graphics.
User  preset  picture  adjustment  in  the  Image  adjust  Menu. 
(pp.40-42)
Image select 
Press the MENU button to display the On-Screen 
Menu. Use the Point ed buttons to select Image 
select and then press the Point 8 or the SELECT 
button.
Use the Point ed buttons to select the desired item 
and then press the SELECT button.
Image Selection
Menu Operation
For viewing pictures in a bright...

40

Image Adjust MenuPress the MENU button to display the On-Screen 
Menu. Use the Point ed buttons to select Image 
adjust and then press the Point 8 or the SELECT 
button.
1
Use the Point ed buttons to select the desired item 
and then press the SELECT button to display the 
adjustment dialog box. Use the Point 7 8 buttons to 
adjust the setting value.
Press the Point 7 button to decrease the contrast; press the 
Point 8 button to increase the contrast (from 0 to 63).
Press the Point 7  button to...