Eiki Projector Lc Hdt1000 User Manual

61

Settings
You can replace the filter with this function. Press the SELECT 
button at Filter control to display a confirmation box. To replace, 
press the SELECT button at Yes and the electrically operated filter 
starts to scroll.
✔Note
• Filter replacement icon and Please wait... message appear on 
the screen when the filter is being scrolled.
• The filter cannot be rewound.
• When the filter is replaced, the total accumulated time of the 
filter use is automatically set to 0.
A confirmation box...

6

Settings
No  signal
4 : 50
Timer left before Lamp is off.
For reducing power consumption as well as maintaining 
the lamp life, the Power management function turns off the 
projection lamp when the projector is not operated for a 
certain period.
Select one of the following options:
 Ready  .................  When the lamp has been fully cooled 
down, the POWER indicator changes 
to green blinking. In this condition, the 
projection lamp will be turned on if the 
input signal is reconnected or...

6

Settings
Key lock
PIN code lock
This function locks the side control and remote control 
buttons to prevent operation by unauthorized persons.
  . . . . .Unlocked.
  . . . . .Locks the operation of the side control.
To unlock, use the remote control
    . . . . .Locks the operation of the remote 
control. To unlock, use the side control.
If the side control accidentally becomes locked and you do 
not have the remote control nearby or there is something 
wrong with your remote control, contact...

64

When the projector is locked with a PIN code, the 
PIN code lock symbol appears in the Guide.
To change the PIN code lock setting
To enter a PIN code
When using side control
Use the Point ed buttons on the side control to select a number. 
Press the Point 8 button to fix the number and move the red 
frame pointer to the next box. The number changes to “✳.” 
Repeat this step to complete entering a four-digit number. After 
entering the four-digit number, move the pointer to “Set.” Press 
the SELECT...

65

Use the Point ed buttons to adjust the Projector ID.
Projector ID ... 1 - 999. (Factory default setting : Projector ID 1)
This feature allows users to set serial communication 
configuration (Projector ID) when several projectors are 
connected via the RS-232C terminal (serial port) of the 
projector.
Shutter function is available to block out light to the screen, 
so that the screen can be used for the other presenters.
Prohibits the shutter operation from the remote control and 
the...

66

When you want to make a digital processing of a projected 
image faster, set this function.
Use the Point ed buttons, select an item of Off/Low/Mid/
High.
Digital processing speed becomes fast by order of Low → 
Mid → High. High is the fastest.Fig.1
✔Note:
• The following functions are not available respectively when 
Video delay control is set to Low/Mid/High.
Low .....Keystone can not be selected.
Mid  ......Progressive and Noise reduction can not be selected.
High  .....  
Keystone, Progressive...

67

Filter replacement icon appears on the screen at a set time.
✔Note: 
• Do not reset the counter when the filter or the filter cartridge is not replaced.
• Timer setting notifies that the filter needs replacement. To replace the filter, use the filter control function (p.61).
Fig.1   Filter replacement icon
Filter cartridge replacement icon appears on the screen when the filter scroll is counted down to 0 scroll.　　
Fig.4   Filter cartridge replacement icon
✔Note:
• Fig.1,  Fig.  2,  Fig.  3  and...

6

This function allows you to change the presentation of the P-
timer and execute it.
Select one of the following options:
 Count up ............  The P-timer display 000:00 appears on 
the screen and the count starts (000:00–
180:00) 
 Count down  ....... The time set in the Timer setting appears 
on the screen and the countdown starts.
 Timer  ................. Use the Point ed buttons to set the 
Timer (1–180 Min). Only set to Count 
down, Timer is active. Factory default 
value is 10 Min....

69

How to Overlap the Projection Images on a Screen 
You can obtain a seamless image by using the Edge Blending function which blends the images projected from multiple 
projectors and digitally dims the edges of the images and the Color Matching function which eliminates color unevenness. 
Follow the steps from 1 to 5 (or 8 if necessary) below to adjust multiple projector images.  
Configure the settings for screen size, image level, and lamp mode. These settings must match those for the rest 
of the...

70

✔Note:
•  
The  overlapping  area  might  become  uneven  depending  on  the  images.  In  such  a  case,  it  is  recommended  to 
decrease the contrast of the images in the Image Adjust Menu.
If the colors of the left and right images do not match, then follow the next step.
Select Color matching in the setting menu and display the Color matching dialog box.
Then, set Color matching to On and adjust the color settings (Red/Green/Blue/White). 
(Refer to pages 57, 58 for operation procedure.)
6...